Model No: T8000 Product Name: 3D Perception Laser SLAM Robot Vacuum Cleaner Please read this instruction carefully before use and keep it properly
Welcome to use Thanks for choosing this smart robot vacuum cleaner.it is an intelligent planning robot vacuum cleaner based on solid linear laser and a variety of sensors, through SLAM algorithm easily and quickly building the real-time map of whole room, and smart planning cleaning paths, starting autocratic cleaning, automatic map partition, 3D obstacle avoidance, automatic charging, etc.
Product Introduction Host Machine 4 start/pause recharging, Partial cleaning short press to start/pause recharging | (3 start/pause cleaning, turn on/off press and hold for 3s to turn on/off machine short press to start/pause cleaning .
Product Introduction Spare parts list charging station X 1 2-in-1 E-water tank (optional) adapter X 1 wiping module {optional) & left side brush X 2 right side brush X 2 individual dust bin X 1
Product Introduction Spare parts list remote control (optional) C5 cleaning brush (optional) remote control (optional) cleaning brush X 1 AAA battery X2 (optional) wiping cloth (optional) (HEAP filter+sponge filter) X1
Product Introduction Host Machine filter screen cover Linear laser wall sensor dust bin push button charging contact Laser ranging sensor universal wheel anti-collision sensor right side brush left side brush battery cover i] = left driving wheel i od rolling brush right driving wheel Lo linear laser sensor left recharge sensor rolling brush / cover buckle
Instructions graphic machine state network state Recharging key power button remarks robe The orange light flashes|The orange indicator blinks Machine boot No distribution network | ou’ until it goes out [slowly until steady on chine Boo Has distribute | The bite light blinks | The blue indicator blinks as distribution network | lowly until it goes out | slowly until steady on No distribution network lights cut Orange light on Machine cleaning electricity » 20% Has distribution network lights out Blue light
Installation 1.Connect adapter and feed the excess power cord into the slot es 2.Place charging station against the wall and connect the power supply | Note: ensure a space of above 0.5m on both sides of the charging station and & space of above 1.5m in the frond. if the power line is vertical to the ground, it may be dragged by the robot and consequently th charging station may be powered off. the charging indicator light is always on when the power is on. 3.
Special Tips 1.Please clear the scattered wire and debris on the ground 2.If the product is used in suspended environments, be sure to before starting, and remove the easy, fragile, valuable and use a strong physical barrier to prevent personal or property potentially dangerous items.Avoid personal or property damage caused by an accidental fall of the host machine. damage caused by winding, getting stuck, dragging or falling down by the main engine.
Installations-Water tank 4.Remove the water tank:When the host completes the work, 1. install the rag: smoothly stick the wiping 3. Install the water tank:Put the dust box press and hold the buttons on both sides in the middle of the cloth to the bottom of the mapping bracket. int the water tank, and put the hand fiat.
Instructions On/Off button 1. long press the button C3 for 3s until the indicator lights is steady on, robot voice prompt "Power On". Robot is muted on successfully. 2. while the machine is in standby state, long press the button (for 3s until the indicator light turn off, robot voice prompt * Power off”. Note: Robot cannot be shut down when it is in charging. Start/Pause cleaning After turn on tha robot, short pass the button yon the host machine or use mobile APP {o start pause cleaning.
Cleaning mode Automatic total cleaning You can use mobile APP, remote controller or the button Gon the robot to enter this mode. The machine will automatically scan the room and generate a map, and divide ths map into several zones. In each zone, robot will start edge cleaning firstly and then planning clean the whole area in a zing-zag path. The machine will complete the cleaning in each partition one by one, orderly and efficiently, full coverage and without omission.
Cleaning mode Local cleaning You can use mobile APP or remote controller or long press the button on the robot for 3s to enter this mode. The robot will take the point of its placement as the center, start an auto cleaning in a square area of 1.5mx1.5m: it will clean along the edge firstly, after the edge path is closed robot will start a zing-zag cleaning in this area for two times, and finally complete a # shape path.
Instructions-Remote controller start automatic cleaning / pause moving forward turning left settling the suction power Mute on / pause UVC Light on / off start/pause recharging turning right adj clean mode Water regulation © Cong Planning moving forward Designated cleaning fuming left /pause Partial cleaning start/pause recharging 12 teems sifting start automatic cleaning / pause turning right edge clean mode selling the suction power
Instructions-Mobile Phone APP APP connection Firmware upgrade please refer to WiFi connection guideline then connect mobile phone APP. Check the firmware upgrade function in the mobile phone APP new firmware is deleted, you can upgrade it as prompted.
