version:1.0 User Manual Blood Pressure Monitor TMB-995-BS Arm Type START STOP Thank you very much for selecting TRANSTEK Blood Pressure Monitor TMB-995-BS. Guangdong Transtek Medical Electronics Co., Ltd. Zone A, No.105 ,Dongli Road, Torch Development District, 528437 Zhongshan,Guangdong,China To use the monitor correctly and safely, please read the manual thoroughly. Please keep well this manual in order to reference in future.
CATALOGUE Table of Contents INTRODUCTION...................................................................................................................2 General Description Indications for Use Contraindications Measurement Principle Safety Information LCD Display Signal Monitor Components List BEFORE YOU START...........................................................................................................
INTRODUCTION General Description Thank you for selecting TRANSTEK arm type blood pressure Monitor (TMB-995-BS). The monitor features blood pressure measurement, pulse rate measurement and the result storage. The design provides you with two years of reliable service. Readings taken by the TMB-995-BS are equivalent to those obtained by a trained observer using the cuff and stethoscope auscultation method.
INTRODUCTION CAUTION * This device is intended for indoor, home use. * This device is not intended for public use. * This device is portable, but it is not intended for use during patient transport. * This device is not suitable for continuous monitoring during medical emergencies or operations. * This device is intended for no-invasive measuring and monitoring of arterial blood pressure.
INTRODUCTION INTRODUCTION LCD Display Signal Monitor Components CUFF AIR HOSE AIR CONNECTOR PLUG START STOP LCD DISPLAY SYMBOL PUL. /min. DESCRIPTION High pressure result Diastolic blood pressure Low pressure result Pulse Pulse/minute Deflating CUFF air is exhausting of deflating Current Time Time(year:month:day:hour:minute) Memory If “MEM” shows, the displayed measurement values is from the memory.
BEFORE YOU START The Choice of Power Supply 1.Battery powered mode: 6VDC 4*AA batteries 2.AC adaptor powered mode: 6V 1A (Please use the AC adaptor which authorized by the manufacturer!) Right picture is the hole in for power adaptor. CAUTION In order to get the best effect and protect your monitor,please use the the right batteries and special power adapter which complies with CE safety standard. Installing and Replacing the Batteries 1.Slide off the battery cover. 2.
BEFORE YOU START BEFORE YOU START 3.When you get the right year, press “ SET ” button to set down and turn to next step. 5.Repeat step 2 and 3 to set the [HOUR] and [MINUTE]. START STOP START STOP 4.Repeat step 2 and 3 to set the [MONTH] and [DAY]. START STOP 10 START STOP START STOP 6.After the [UNIT] is set, the LCD will display “donE”, and then turn off.
BEFORE YOU START Select the User 1.When the monitor is off , press the “ SET ” button to enter user setting mode. MEASUREMENT Tie the Cuff 1. Remove all jewelry, such as watches and bracelets from your left arm. Note: If your doctor has diagnosed you with poor circulation in your left arm, use your right arm. 2. Roll or push up your sleeve to expose the skin. Make sure your sleeve is not too tight. START STOP 2.Then press “ SET ” button again, select the user ID between user 1 and user 2 . 3.
MEASUREMENT MEASUREMENT Start the Measurement 1.When the monitor is off,press the START/STOP button to turn on the monitor, and it will finish the whole measurement, save and transmit the measurement data for the desired user. (Take User 1 for example.) LCD display Inflating and measuring. START STOP 3.If the data is successfully transmitted, the Bluetooth symbol doesn’t blink any more, and the will disappear. If the data transmission fails, the will proceed. Adjust the zero .
DATA MANAGEMENT DATA MANAGEMENT Delete the Records Recall the Records 1.When the monitor is off, please press “ MEM ” button to show the average value of the latest three records.If the records are less than 3 groups, it will display the latest record instead. Displays different colors at different levels when the monitor is under the memory enquiry mode. (Take user 1 for example.) 2. Press the “ MEM ” or “ SET ” button again to rotate the records.
INFORMATION FOR USER DATA MANAGEMENT 3.Hold pressing “ SET ” button for 3 seconds when the monitor is under the memory enquiry mode (excluding the LCD displays AVG). The LCD will display the blinking “ Use ID + dEL ONE”. Tips for Measurement Measurements may be inaccurate if taken in the following circumstances. 4.Press “ MEM ” button to confirm deleting the last record, the LCD will display “Use ID + dEL dOnE” and the monitor will turn off. 5.
INFORMATION FOR USER ABOUT BLOOD PRESSURE Maintenance What are systolic pressure and diastolic pressure? In order to get the best performance, please follow the instructions below. When ventricles contract and pump blood out of the heart, the blood pressure reaches its maximum value in the cycle, which is called systolic pressure. When the ventricles relax, the blood pressure reaches its minimum value in the cycle, which is called diastolic pressure.
ABOUT BLOOD PRESSURE TROUBLESHOOTING This section includes a list of error messages and frequently asked questions for problems you may encounter with your blood pressure monitor. If the product is not operating as you think it should, check here before arranging for servicing. Why does my blood pressure fluctuate throughout the day? PROBLEM SYMPTOM 1. Individual blood pressure varies multiple times everyday.
SPECIFICATIONS Power supply Display mode Measurement mode Measurement range Accuracy AUTHORIZED COMPONENT Battery powered mode: 6VDC 4×AA batteries AC adaptor powered mode: 6V 1A (Please only use the recommended AC adaptor model). Digital LCD V.A.60mm*80mm A temperature range of :+5°C to +40°C Measurement perimeter of the upper arm Weight External dimensions Attachment Mode of operation Degree of protection Protection against ingress of water Device Classification Software Version 1.
FCC STATEMENT FCC Statement FCC ID:OU9TMB995BS2 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Caution: The user is cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
EMC GUIDANCE EMC GUIDANCE Table 2 Table 3 Guidance and manufacturer’s declaration – electromagnetic Immunity Immunity Test IEC 60601-1-2 Test level Electrostatic discharge (ESD) IEC 61000-4-2 ±8 kV contact ±2 kV, ±4 kV, ±8 kV, ±15 kV air ±8 kV contact ±2 kV, ±4 kV, ±8 kV, ±15 kV air Electrical fast transient/burst IEC 61000-4-4 ±2 kV for power supply lines ±1 kV signal input/output 100 kHz repetition frequency ±2 kV for power supply lines Not Applicable 100 kHz repetition frequency Surge IEC6100
