version:1.0 User Manual Blood Pressure Monitor TMB-1583-BT Arm Type MEM START STOP Guangdong Transtek Medical Electronics Co., Ltd. Zone A, No.105 ,Dongli Road, Torch Development District, Zhongshan,528437,Guangdong,China SET Thank you very much for selecting TRANSTEK Blood Pressure Monitor TMB-1583-BT. Please do read the user manual carefully and thoroughtly so as to ensure the safe usage of this product, and keep the manual well for further reference in case you have problems.
CATALOGUE CATALOGUE Table of Contents INTRODUCTION...................................................................................................................2 General Description Indications for Use Safety Information LCD Display Signal Monitor Components BEFORE YOU START...........................................................................................................
INTRODUCTION INTRODUCTION General Description Thank you for selecting TRANSTEK arm type blood pressure Monitor (TMB-1583-BT). The monitor features blood pressure measurement, pulse rate measurement and the result storage. The design provides you with two years of reliable service. Readings taken by the TMB-1583-BT are equivalent to those obtained by a trained observer using the cuff and stethoscope auscultation method.
INTRODUCTION INTRODUCTION CAUTION This device is intended only for adult use in homes. This device is intended for non-invasive measuring and monitoring of arterial blood pressure. It is not intended for use on extremities other than arm or for functions other than obtaining a blood pressure measurement. If you experience discomfort during a measurement, such as pain in the arm or other complaints, press the START/STOP button to release the air immediately from the cuff.
INTRODUCTION INTRODUCTION Monitor Components SYMBOL DESCRIPTION EXPLANATION Error Error Hour The hour in the clock mode Minute The minute in the clock mode Second The second in the clock mode Heartbeat Heartbeat detection during the measurement User 1 Start measurement,save and transmit the measuring results for User 1 User 2 Start measurement,save and transmit the measuring results for User 2 Bluetooth icon The bluetooth icon blinks when the bluetooth is working LCD DISPLAY AIR HOSE C
BEFORE YOU START BEFORE YOU START The Choice of Power Supply Measurement Principle 1.Battery powered mode: 6VDC 4×AAA alkaline batteries 2.AC adaptor powered mode: 6V 1A (Please only use the recommended AC adaptor model). MEM START STOP SET Please unplug the adaptor to depart from the using utility power. AC adaptor CAUTION In order to get the best effect and protect your monitor,please use the right battery and special power adaptor which complies with U.S. safety standard.
BEFORE YOU START BEFORE YOU START 3.When you get the right year, press “SET” button to set down and turn to next step to set the date format between “M/D” or “D/M”. 6.Repeat steps 2 and 3 to set the [UNIT]. 4.Repeat steps 2 and 3 to set the [DATE FORMAT], then set the [MONTH] and [DAY]. 7.Repeat steps 2 and 3 to set the clock mode. 5 .Repeat steps 2 and 3 to set the [TIME FORMAT] between 12H or 24H, then set the [HOUR] and [MINUTE]. 8.
BEFORE YOU START Select the User 1.When the monitor is off , press and hold the MEM button to enter user setting mode. The user ID will blink. BEFORE YOU START Pair-up the Blood Pressure Monitor with Your Device 1.Turn on Bluetooth and the app. Make sure both are ON when pair-up is proceeding. 2.When the monitor is OFF, press and hold the START/STOP button to start pair-up. The bluetooth symbol will blink, indicating pair-up is proceeding. 2.
MEASUREMENT MEASUREMENT Tie the cuff Start the Measurement 1.When the monitor is off, press the “START/STOP” button to turn on the monitor, and it will finish the whole measurement. (Take User 1 for example.) 1.Tie the cuff on your upper arm, then position the tube off-center toward the inner side of arm in line with the little finger. LCD display 2.The cuff should be snug but not too tight. You should be able to insert one finger between the cuff and your arm. Adjust to zero. 2~3cm 3.
MEASUREMENT DATA MEASUREMENT 2.This device will proceed Recall the Records to data transmission after measurement. The Bluetooth symbol blinks on the LCD indicates data is transmitting. 1. When the monitor is off, please press “MEM” button to show the average value of the latest three records. (Take User 1 for example.) 2. Press “MEM” button or “SET” button to get the record you want. If the data transmission fails, the LCD will display . If the data transmission succeeds, the LCD will display .
DATA MANAGEMENT SPECIAL FUNCTION About the Clock mode Delete the Records If you did not get the correct measurement, you can delete all results by following steps below.(Take User 1 for example) 1.Hold pressing “MEM” button for 3 seconds when the monitor is in the memory recall mode ,the flash display “ User ID+ dEL ALL” will show. 2.Press “SET” button to confirm deleting and the monitor will display “dEL dOnE” and then turn off.
INFORMATION FOR USER INFORMATION FOR USER Tips for Measurement Measurements may be inaccurate if taken in the following circumstances. Maintenance In order to get the best performance, please follow the instructions below. ME M STA RT STO P SET MEM START STOP SET Put in a dry place and avoid the sunshine Within 1 hour after dinner or drinking Avoid touching water, clean it with a dry cloth in case.
ABOUT BLOOD PRESSURE ABOUT BLOOD PRESSURE What are systolic pressure and diastolic pressure? When ventricles contract and pump blood out of the heart, the blood pressure reaches its maximum value in the cycle, which is called systolic pressure. When the ventricles relax, the blood pressure reaches its minimum value in the cycle, which is called diastolic pressure.
TROUBLESHOOTING SPECIFICATIONS This section includes a list of error messages and frequently asked questions for problems you may encounter with your blood pressure monitor. If the products not operating as you think it should, check here before arranging for servicing. PROBLEM SYMPTOM No power Low batteries Display will not light up. Display is dim or show Err shows E 1 shows E 2 shows Error massage E 3 shows E10 or E11 shows E20 shows 24 CHECK THIS REMEDY Batteries are exhausted.
AUTHORIZED COMPONENT Authorized Component COMPLIED STANDARDS LIST Complied Standards List 1.please use the TRANSTEK authorized adapter. Adapter Type：KH0601000UW Input：100~240V~ 50/60Hz, 0.4A Max Output：6V Risk management Labeling ISO/EN 15223-1:2012 Medical devices. Symbols to be used with medical device labels, labelling and information to be supplied.
FCC STATEMENT FCC Statement EMC GUIDANCE EMC Guidance FCC ID: OU9TMB1583-B This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
