Guangdong Transtek Medical Electronics Co., Ltd. Zone A, No.105 ,Dongli Road, Torch Development District, Zhongshan,528437,Guangdong,China Arm Type TMB-1491-BT Please do read the user manual carefully and thoroughtly so as to ensure the safe usage of this product, and keep the manual well for further reference in case you have problems. Thank you very much for selecting TRANSTEK Blood Pressure Monitor TMB-1491-BT. Blood Pressure Monitor User Manual version:1.
CATALOGUE TROUBLESHOOTING........................................................................................................22 SPECIFICATIONS..............................................................................................................23 AUTHORIZED COMPONENT ...........................................................................................24 CONTACT INFORMATION.................................................................................................
F1 SN For indoor use only Symbol for “Class II Equipment” 7 $ 9 ĭ &&& Symbol for “Including RF transmitter” Symbol for “ENVIRONMENT PROTECTION - Electrical waste products should not be disposed of with household waste. Please recycle where facilities exist.
SYMBOL Beats per minute, BPM CUFF air is exhausting of deflating The displayed measurement values is from the memory.
AC adaptor shows Remove the old batteries from the device and follow your local recycling guidelines. Do not dispose of batteries in fire. Batteries may explode or leak. The old batteries are harmful to the environment, do not dispose with other daily trash. Remove batteries if the device is not likely to be used for some time. CAUTION The display does not light up The display dims The Replace the batteries whenever the below happen Open the battery cover.
2.Press the “MEM” button to change the [YEAR]. 1.When the monitor is off, hold pressing “SET” button for 3 seconds to enter the mode for year setting. Or when the monitor is off, press “SET” button shortly, it will display the time. Then hold pressing “SET” button to enter the mode for year setting. It is important to set the clock before using your blood pressure monitor, so that a time stamp can be assigned to each record that is stored in the memory.
8.After the unit is set,the LCD will display “done” and then turn off. 7.Repeat steps 2 and 3 to set the [UNIT]. 6.Repeat steps 2 and 3 to set the [HOUR] and [MINUTE]. BEFORE YOU START 3. After selecting the suitable user ID, press SET button to confirm. Then the LCD will turn off. 2.Then press MEM button again, select the user ID between user 1 and user 2. 1.When the monitor is off , press and hold the MEM button to enter user setting mode. The user ID will blink.
will be shown on the LCD. If FAIL, only bluetooth symbol Bluetooth Module No.: AW8001 RF Frequency Range: 2402 MHz to 2480 MHz Output Power Range: 0 dBm Supply Voltage: 1.8-3.6 V Transmitting Distance: 10 meters 4.The monitor will shut off after Pair-up process is complete. If SUCCEED, symbol will be shown on the LCD. 3.Then please select the user ID you want to connect with your smartphone on the app to continute the pair-up. 2.
Inflating and measuring. LCD display Adjust to zero. START STOP Display and save the results. The device will proceed to data transmission after measurement. The Bluetooth symbol blinks on the LCD indicates data is transmitting. 1.When the monitor is off, press the “START/STOP” button to turn on the monitor, and it will finish the whole measurement . Start the Measurement MEASUREMENT 2.Press the “START/STOP” button to power off, otherwise it will turn off within 1 minute.
UP The current No. is No. 4. The corresponding date is March 20th. The corresponding time is P.M. 10:00. DOWN The most recent record (1) is shown first. Each new measurement is assigned to the first (1) record. All other records are pushed back one digit (e.g., 2 becomes 3, and so on), and the last record (60) is dropped from the list. CAUTION The date and time of the record will be shown alternately. 2. Press “MEM” button or “SET” button to get the record you want. 1.
Immediate measurement after tea, coffee, smoking When talking or moving your fingers When you want to discharge urine Within 1 hour after dinner or drinking Within 20 minutes after taking a bath In a very cold environment Measurements may be inaccurate if taken in the following circumstances. Tips for Measurement INFORMATION FOR USER Do not attempt to clean the reusable cuff with water and never immerse the cuff in water.
Diastolic blood entering vein relax Systolic blood discharging artery press 140-159 160 or higher Higher than 180 High Blood Pressure (Hypertension) Stage 1 High Blood Pressure (Hypertension) Stage 2 Hypertensive Crisis (Emergency care needed) or or Higher than 110 100 or higher 90-99 80-89 or 120-139 Prehypertension or less than 80 Diastolic mmHg (lower#) and Systolic mmHg (upper#) less than 120 Normal Blood Pressure Category This chart reflects blood pressure categories defined b
Error massage Low batteries No power REMEDY The monitor detected motion,talking or the pluse is too poor while measuring. E10 or E11 shows The treatment of the measurement failed. A calibration error occurred. EExx,shows on the display. Retake the measurement. If the problem persists, contact the retailer or our customer service department for further assistance.Refer to the warranty for contact information and return instructions. Relax for a moment and then measure again.
1000mA Manufactured by: Guangdong Transtek Medical Electronics Co., Ltd. Company: Guangdong Transtek Medical Electronics Co., Ltd. Address: Zone A, No.105 ,Dongli Road, Torch Development District, Zhongshan,528437,Guangdong,China For more information about our products, please visit www.transtek.cn.you can get customer service, usual problems and customer download, transtek will serve you anytime. Contact Information 2XWSXW˖6V $GDSWHU 7\SH˖KH0601000UW ,QSXW˖100~240V~ 50/60Hz, 0.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on,the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
