Version:1.0 User Manual Blood Pressure Monitor TMB-1014-BT Wrist Type Zhongshan Transtek Electronics Co., Ltd Jin’an Road, Minzhong, Zhongshan 528441, Guangdong, China Thank you very much for selecting TRANSTEK Blood Pressure Monitor TMB-1014-BT. To use the monitor correctly and safely, please read the manual thoroughly. Please well keep this manual in order to reference in future.
CATALOGUE INTRODUCTION 1 Safety information LCD display signal Monitor components BEFORE YOU START 4 The Choice of power supply Installing and replacing the batteries Setting Date, time and measurement unit MEASUREMENT 7 Tie the cuff Strat a measurement THE OPERATION OF RECALLING RECORDS
INTRODUCTION INTRODUCTION LCD display signal Monitor components SYSTOLIC MEM/UP BUTTON DIASTOLIC GRADE PULSE RATE LCD DISPLAY 6 < 0 % 2 / ' ( 6 & 5 ,3 7 ,2 1 START/OFF BUTTON TIME SET/DOWN BUTTON ( ; 3 /$ 1 $ 7 ,2 1 Systolic blood pressure High pressure result Diastolic blood pressure Low pressure result Pulse Pulse/minute Low battery Batteries are low and need to be replaced mmHg Measurement unit the blood pressure Grade The grade of the blood pressure For instructions,refer to Pa
BEFORE YOU START BEFORE YOU START The installment and replacement of battery Setting Date, time and measurement unit Slide off the battery cover. Install the batteries by matching the correct polarity, as shown below. Always use the correct battery type (2 alkaline LR03AAA-size). Replace the cover. It is important to set the clock before using your blood pressure monitor, so that a time stamp can be assigned to each record that is stored in the memory.
BEFORE YOU START BEFORE YOU START Bluetooth phones’ test software 4.Repeat the 2 and 3 to set the [Minute]. 1.Open the Bluetooth 4.0 special test MEM mobile phones after electrify blood pressure monitor. 2.After operating Bluetooth Test program (It is about 8 m from mobile to blood pressure monitor), the “discovered device” column will remind “searching for device”... SET 5.Repeat the 2 and 3 to set the [YEAR], [MONTH] and [DAY]. MEM MEM 3 .
BEFORE YOU START 6.When the blood pressure monitor show “[ ]”, it means matching successfully; When it display”E1”, it indicates matching unsuccessfully. 7.If matching successfully, it will show the lately measuring record on the “receive data” column. 8.Choose “Bloodpressure Record” to view the history record. MEASUREMENT Positioning the wrist cuff 1 .Remove all accessories (watch, bracelet, etc) from your left wrist.
MEASUREMENT MEASUREMENT Start the Measurement Please press the SET to choose the user 1 or user 2 when the blood pressure monitor turn off 1.Press the START/STOP, it will finish the whole measurement automatically. Adjust the zero automatically. Inflating and measuring automatically. Display and save the results automatically. START STOP 2.A f te r me as u rin g， i t’ ll d is pl ay t he mo v in g “o” a nd s en d dat a at th e s ame t ime. 3.
THE OPERATION OF RECALLING RECORDS THE OPERATION OF RECALLING RECORDS Recalling the records 1.Press the “MEM” to show the last 3 average of the record. Deleting a measurement record from memory MEM If you did not get the correct measurement, you can delete all results by following below steps. 1.Hold pressing “MEM” for 3 MEM seconds, when the memory is SET shown. SET 2. Press the “MEM” or “SET” to get the record you want. MEM UP 2.When flash “Delete all”, press the “SET” to delete the memory.
INFORMATION INFORMATION FOR USER Tips for measurement Maintenance It can cause incorrectness if the measurement are taken in the following circumstances. Wait at least 1 hour after dinner or drinking Wait at least 20 minutes after taking a bath In a very cold enviroment Immediate measurement after tea, coffee, smoking In order to get the best performance, please follow the below instructions. Put in a dry place and avoid the sunshine Avoid touching water, clean it with a dry cloth in case.
ABOUT BLOOD PRESSURE ABOUT BLOOD PRESSURE What are systolic pressure and diastolic pressure? When ventricles contract and pump blood out of the heart, blood pressure reaches its maximum value, the highest pressure in the cycle is known as systolic pressure. When the heart relaxes between heartbeats, the lowest blood pressure is diastolic pressure.
SPECIFICATIONS TROUBLESHOOTING This section includes a list of error messages and frequently asked questions for problems you may encounter with your blood pressure monitor. If the products not operating as you think it should, check here before arranging for servicing. PROBLEM SYMPTOM No power Low batteries Error massage Display is dim or will not light up. REMEDY Batteries are exhausted. Replace with new batteries Batteries are inserted incorrectly. Show on Batteries are low.
CONTACT INFORMATION & R Q WDFW ,Q IR UP DWLR Q For more information about our products, please visit www.transtek.cn.you can get customer service, usual problems and customer download, transtek will serve you anytime. Manufactured by: ZHONGSHAN TRANSTEK ELECTRONICES CO.,LTD Conpany: ZHONGSHAN TRANSTEK ELECTRONICES CO.
Table 2 Guidance and manufacture’s declaration – electromagnetic immunity – for all ME EQUIPMENT and ME SYSTEMS Table 4 Guidance and manufacture’s declaration – electromagnetic immunity – for ME EQUIPMENT and ME SYSTEMS that are not LIFE-SUPPORTING Guidance and manufacture’s declaration – electromagnetic immunity Guidance and manufacture’s declaration – electromagnetic immunity The TMB-1014-BT is intended for use in the electromagnetic environment specified below.
NOTE 1 At 80 MHz and 800 MHz, the higher frequency range applies. NOTE 2 These guidelines may not apply in all situations. Electromagnetic propagation is affected by absorption and reflection from structures, objects and people. a Field strengths from fixed transmitters, such as base stations for radio (cellular/cordless) telephones and land mobile radios, amateur radio, AM and FM radio broadcast and TV broadcast cannot be predicted theoretically with accuracy.
This device complies with Part 15 and Part 18 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Caution: The user is cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
