User's Manual

This section includes a list of error messages and frequently
asked questions for problems you may encounter with your blood
pressure monitor. If the products not operating as you think it
should, check here before arranging for servicing.
3.7V 1000mAH Built-in rechargeable
li-polymer battery, 6V 1A AC Adaptor
Digital LCD display
V.A.= 86.1mm(L) x24mm(W)
Approx.285g
Approx.130.9mm×73mm×29.4mm
AC Adaptor,user manual
A01
Power supply
Display mode
Measurement mode
Oscillographic testing mode
Measurement range
Accuracy
Normal working condition
Storage & transportation
condition
Measurement perimeter
of the arm
Weight
External dimensions
Attachment
Mode of operation Continuous operation
Degree of protection Type BF applied part
Protection against
ingress of water
Software version
Device classification
Battery Powered Mode:
Internally Powered ME Equipment
AC Adaptor charged Mode:
Class II ME Equipment
WARNING: No modification of this equipment is allowed.
Pressure:
5°C-40°C within±3mmHg(0.4kPa)
Pulse value:±5%
Rated cuff pressure:
0mmHg~299mmHg(0kPa ~ 39.9kPa)
Measurement pressure:
SYS: 60mmHg~230mmHg (8.0kPa~30.7kPa)
DIA: 40mmHg~130mmHg (5.3kPa~17.3kPa)
Pulse value: (40-199)beat/minute
IP22: The first number 2: Protected against solid
foreign objects of 12,5mm Ф and greater. The second
number: Protected against vertically falling water
drops when enclosure titled up to 15º. Vertically falling
drops shall have no harmful effects when the
enclosure is titled at any angle up to 15º on either side
of the vertical.
About 22cm-32cm or 22cm-42cm
A temperature range of :+5°C to +40°C
A relative humidity range of 15% to 90%,
non-condensing, but not requiring a water
vapour partial pressure greater than 50 hPa
An atmospheric pressure range of :
700 hPa to 1060 hPa
Temperature:-20°C to +60°C
A relative humidity range of ≤ 93%, non-condensing,
at a water vapour pressure up to 50hPa
PROBLEM SYMPTOM CHECK THIS REMEDY
No power
Low
batteries
Error
message
Display will not
light up.
E1 shows
The cuff is not secure.
E 3 shows
Relax for a moment
and then measure again.
E 10 or
E 11 shows
The monitor detected
motion,talking or the
pulse is too poor while
measuring.
E 20 shows
E 21 shows Relax for a moment and
then measure again.
EExx,shows on
the display.
A calibration error
occurred.
Retake the measurement.
If the problem persists,
contact the retailer or our
customer service
department for further
assistance.Refer to the
warranty for contact
information and return
instructions.
The measurement
process does not detect
the pulse signal.
Loosen the clothing on
the arm and then
measure again.
The treatment of the
measurement failed.
Power is exhausted. Charge the power
Power is low. Charge the power
Display is dim or
shows
AC adaptor is inserted
incorrectly.
Insert the AC adaptor
tightly
Refasten the cuff and then
measure again.
Warning
message
out shows
Out of measurement
range
the measurement result is out of
the measurement range (SYS:
60mmHg to 230mmHg; or DIA:
40mmHg to 130mmHg;or
Pulse: 40-199 pulse/minute)
Relax for a moment
and then measure again.
The pressure of the
cuff is excess.
TROUBLESHOOTING
SPECIFICATIONS
26 27