Fireplace User Guide ® MODEL#: EF19-42A SAVE THESE INSTRUCTIONS THIS PRODUCT WAS MANUFACTURED BY PAITE FOR ASHLEY FURNITURE INDUSTRIES, INC. All Rights Reserved.
Table Of Contents Table of Contents ..................................................................................................................................2 IMPORTANT SAFETY INFORMATION ............................................................................. 3-4 PREPARATION ..........................................................................................................................................5 GROUNDING INSTRUCTIONS ..........................................................
IMPORTANT SAFETY INFORMATION PLEASE READ AND CAREFULLY FOLLOW ALL OF THE INFORMATION AND INSTRUCTIONS IN THIS USER GUIDE, INCLUDING ALL SAFETY, OPERATING, AND MAINTENANCE INFORMATION. IF THE INFORMATION IN THIS USER GUIDE IS NOT FOLLOWED EXACTLY, FIRE, ELECTRIC SHOCK, BURN, DEATH OR OTHER SERIOUS INJURY AND/OR PROPERTY DAMAGE MAY RESULT. You electric fireplace is fully assembled from the factory. No assembly is required to begin using the fireplace. There are no user serviceable parts inside the fireplace.
IMPORTANT SAFETY INSTRUCTIONS Read all instructions before using this fireplace. When using electrical appliances, basic precautions should always be followed to reduce the risk of fire, electrical shock, injury or death and property damage. Such precautions include, but are not limited to, the following: 1. This fireplace is hot when in use and for several minutes after use. To avoid burns, do not touch hot surfaces of the fireplace such as the heated venting areas of the fireplace.
PREPARATION GROUNDING INSTRUCTIONS This product must be grounded. This product is equipped with a cord having an equipmentgrounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances. This fireplace is for use on 120 volts circuit and has a grounded plug that looks like the one illustrated on Figure 1. See Figure 1 for grounding instruction.
SITE PREPARATION Ensure the power cord is not installed so that it is pinched or against a sharp edge and ensure that the power cord is stored and secured to avoid tripping or snagging to reduce the risk of fire, eletric shock,property damage, serious injury or death. Locating Your Fireplace Read and follow the important safety instruction in this user guide. Failure to do so may result in serious bodily injury, death, or property damage.
FCC STATEMENT NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
OPERATIONS AND FEATURES Using the Remote Control Power This will turn the unit ON and OFF. When it is turn OFF, the fan will continue to continue to run after turning off the heating function to cool and protect heating function to cool and protect period of 3 minutes .When the unit is turned back ON, the system will recall the last heat setting used. Store flame and heating setting. Adjust Brightness This allows you to raise or lower the level of flame brightness.
Using the Fireplace Touch Control Panel Thermostat Adjust Temperature This allows programming ℉ and ℃ will be displayed along of the thermostat. The with the temperature on the fireplace can be used main display. The fireplace can without the heater if be used without the heater if desired. Simply cycle desired, simply cycle through the through the function until function until no temperature is no temperature is displayed. displayed.
Using the Wireless Touch Control Panel Power This will turn the Wireless Connection ON and OFF. Volume + This allows you to turn up the volume. Volume － This allows you to turn down the volume. Pause This allows you to pause the player. Note: Hold the button for 3 seconds you can enter AUX, USB, wireless selection mode, then select the right mode for playing.. Next This allows you to select next track. Previous This allows you to select previous track.
The Fireplace Remote Control The remote combines all the functions of the front panel controls for flexibility and convenience when changing desired settings. The first thing to do with the remote control is to remove the plastic sheet insulated the battery. (The battery is supplied with the remote control.) Replacement batteries can be purchase at any electronics store. The part number for the battery is CR2025. Please follow the sequence below to replace the battery. 1.
CARE AND MAINTENANCE Light Emitting Diode This fireplace is fitted with LED (Light Emitting Diode) bulbs in place of conventional bulbs. These generate the same light levels as convention bulbs, but use a fraction of the energy. These LED bulbs are maintenance free and should not require replacing during the life of the product. Cleaning WHILE IN USE AND FOR SEVERAL MINUTES AFTER USE, THE FIREPLACE UNIT CAN GET HOT INCLUDING, BUT NOT LIMITED TO, THE TOP CENTER OF THE FIREPLACE.
CIRCUIT DIAGRAM If the fireplace appears to malfunction, turn the unit off and unplug the fireplace from the wall immediately. Please contact the store that this was purchased from with the original purchase receipt or call 1 (800) 477-2222 for service related questions or concerns. Please do not attempt to repair the electric fireplace. HARDWARE The fireplace includes brackets to fix the insert in place inside the furniture.
TROUBLE SHOOTING GUIDE There are no user serviceable parts inside the fireplace. If the unit appears to malfunction, turn the unit off and unplug the unit from the wall immediately. Please contact the store that this was purchase from with the original purchase receipt or call 1 (800) 477-2222 for service related questions or concerns.
FCC Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
