Smart Robot Vacuum Cleaner T1 User Manual Please read the User Manual before using---Warranty card included, pictures are for reference only.
Safety information Service restriction This product is intended for floor cleaning use only in the home environment. Do not use it outdoors (such as open balcony), non-ground surface (such as sofas), commercial or industrial environments. nvironment (such as a duplex flat, open balcony, top of home) without a protective fence. nvironment where the temperature is above 40°C or below 0°C, or there is any liquid or viscous substance.
Packing list and introduction Main machine x1 Partial cleaning button Short press to activate partial cleaning. Charging button Short press to activate the charging function. Cleaning/Power button Short press to activate the cleaning function. Reset WiFi Press and hold the Partial cleaning button and the Charging button for more than 3 seconds at the same time. Note: Press any button to pause during cleaning/charging or partial cleaning.
Packaging list and introduction Main machine Laser distance sensor Speaker TOF sensor for wall/ Infrared auxiliary charger sensor Infrared charger sensor/ Infrared anti-collision sensor Collision sensor Laser head cover Laser head cover pressure sensor Infrared auxiliary charger sensor Dust box Dust box opening button Vent outlet
Packaging list and introduction Main machine Docking electrode slice for charging Universal wheel Side brush Driving wheel Rolling brush Docking electrode slice for dust collecting Accessories list for Smart Robot Vacuum Cleaner Water tank x1 Disposable mop x10
Packaging list and introduction Dust box module x1 Mopping module x1 Find and install the filter screen before using Dust box fastene Cleaning tool Find and install the water tank and mop (or disposable mop) before using Water tank Water tank cover Dust box lower bracket Paste area Water tank filter element Water tank wheel set Dust box flip cover Mop Dust box button Water tank fastener Dust box upper bracket Dust box filter screen
Packaging list and introduction List of optional accessories (Users can choose one of the two sets according to actual demands----Charging base + Charging base adapter or Dust collector + Dust collector charging wire.) 1.Charging base Charging base indicator Signal emission zone Charging Contact Pins Power port Front side of charging base Back side of charging base Charging base adapter 2.
Installation 1.Install the charging base Place the charging base on a flat surface against the wall. Against the wall Ensure that there is more than 1.2-meter clear space in front and more than 0.5-meter clear space on both sides of the charging base.
Installation Long press the button for power-on. Press the charging ley, the machine will find the charging base automatically for charging. The color of power button indicates the power of the battery. White light: power>15% Orange breathing light: power<15% on the charging clip of the charging base. The orange light of the power button will be always on when charging.
Installation 2.Install the dust collector Place the dust collector 6mm or more away from the wall on a flat surface 0.06m away from the wall Ensure that there is more than 1.2-meter clear space in front and more than 0.5-meter clear space on both sides of the dust collector.
Installation Connect to the mobile client (skip the step if APP control isn’t required) 1.Download APP 2.Register Search “Lenovo Cleaner T1” in App Store (Apple: search “Lenovo Open “Lenovo Cleaner T1”APP to register or login account. Google Play) to download and install. Lenovo Cleaner T1 3.Enter Network Distribution Status 4.WiFi Network Configuration Put the cleaner on the ground and press the “Charging button” and “Partial cleaning button” for more than 3 seconds.
Installation Installation and removal of mopping module Install mop: Wet out the mop and dry it until there is no water drop. Put the mop on the mopping module and stick it firmly. Do not use the mopping function when there is nobody at home. If there are carpets in the home, please set restricted areas on App. Install module: Push the joint on the mopping module in parallel along the back of the machine. When hearing the "click", it means that the installation is in place.
Instructions Whole house cleaning Long press button for power-on. The indicator of the button turns on slowly, and the machine gets in standby state. When Press the button to start the whole house cleaning (see the picture of cleaning route as below). Press any button to pause while cleaning. The white light slowly extinguishes, and the cleaning is over. Note: The machine cannot shut down during charging.
Instructions Partial cleaning Sleep mode When the machine is on standby or pause, press the partial cleaning button to start partial cleaning. This mode can clean a 1.6m x 1.6m square area taking the machine as the center. After the cleaning, the machine will automatically return to the starting position and stop working. If there is no operation for more than 20 minutes, the machine will enter sleep mode automatically.
Routine maintenance Main brush (Weekly cleaning is recommended) 1.Turn over the machine, press down the fastener and remove the main brush cover. 2.Take the main brush out and clean the main brush bearing. 3.Cut the winding hair on the main brush with the matching cleaning tool of the main brush. 4.Re-install the main brush and press down the main brush cover tight, then fix the fastener.
Routine maintenance Side brush (Weekly cleaning is recommended) Use a screwdriver to unscrew and clean the side brush. Note: Battery The machine has built-in high performance rechargeable lithium battery pack. For maintaining battery performance, please keep the machine in charging for daily use. Note: If not use it for long, please shut down and store it. Charge it at least once every three months to avoid battery damage due to over-discharge.
Routine maintenance Dust box and filter screen (Weekly cleaning is recommended) 1.Press the dust box releasing button to remove it. 2.Open the dust box fastener. 3. Clean up the garbage. 4.Open the dust box cover and remove the mesh cover and filter screen(HEPA).
Routine maintenance 6.Fill the dust box with clean water, close and shake it, then pour out the dirty water inside. Repeat this step several times until the dust box is cleaned up. Note: It is recommended to replace the filter every 3-6 weeks. Mop (Cleaning after each use is recommended) 1.Remove the mop from the mopping module. 2.Clean mop and air it Note: to avoid backfilling of dirty water that would clog the filter element.
Routine maintenance Machine Sensor Wipe the sensors of the machine with a soft and dry cloth, including: 2.Wall sensor on the right side of the machine. 3.Charging docking electrode slice at the bottom of the machine 4.The dust collecting electrode slice at the bottom of the machine. 5.Infrared auxiliary charger sensor.
Routine maintenance Filter element part (Replacement of every 1-3 months Universal wheel (Monthly cleaning is recommended) is recommended) 1.Remove the old filter element part on the left and right side along the notch with your fingers. 2.Install the new filter element part and confirm that it is in place. Water tank filter element Wheel 1.Turn over the machine and pull out the universal wheel. 2.Clean the hair and dirt on the wheel and axle. 3.Re-install the wheel and Bracket press it tightly.
Basic parameters Machine Charging base Name External size Parameter 350 Battery type Product weight Rated voltage Rated power Name 350 98mm External size 3200mAh Parameter 145 140 Rated power 3.6kg 14.4V 99mm 30W Rated input 24V 1.2A Rated output 24V 1.2A 50W Troubleshooting When abnormalities occur in the operation of the machine, the power button indicator flashes orange quickly. Please refer to the table below for troubleshooting.
FAQ Fault prompt Resolution Please check whether the main wheel is stuck. The machine may be stuck or trapped. Please clear the obstacles around the machine. Please install the dust box and filter screen, and make sure that they are installed in place. Dust box removed Clean the dust box and filter screen. If the filter screen is not entirely dry, please air it for at least 24 hours. The filter screen may be blocked, please clean it. If the problem is not solved, please change for a new filter screen.
FAQ Fault prompt Resolution Fail to return to the charging base There are too many obstacles near the charging base. Please put the charging base in an open area. The machine is too far from the charging base. Please put the machine near the charging base and retry. Abnormal behavior Reboot the machine. Abnormal noise occurs when cleaning Main brush, side brush or main wheel may be twisted with foreign matters. Please shut down and clean.
Warranty information Product name Warranty coverage Main components Robot Vacuum Cleaner Peripheral components Consumables Software Part name Machine Charging base, power cord Edge brush, main brush, filter screen, main brush cover, mop, filter element Attached software (including attached software materials) Warranty Period (Month) Warranty Service Type 12 Fetch, send, express and repair 12 Fetch, send, express and repair 0 Not applicable 0 Not applicable Remarks
Warranty card Dear users, this warranty card is your certificate to apply for warranty, please cooperate with the seller to fill in and keep it properly! Address Information Contact number Product name Product information Postal Code Product model Product Bar Code/Serial Number/Batch Number Name Seller Information Address Contact number Sales date Postal Code Invoice number Remarks If you need any support relates to your product please contact the agency you purchased from.
FCC STATEMENT 1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
