Instruction Manual

ManualsBrandsGuangdong Lejie Intelligent Technology ManualsPersonal Caresonic electric toothbrush

Please read the instruction manual of this product carefully.

Warning:

1. check for any visible damage before each use.

2. Do not use if damaged or severely damaged.

3. Before you connect the power cord, check that the local power supply voltage is consistent with the

voltage indicated by the product.

4. Do not use the charging stand if it is damaged in any way.

5. This product (including toothbrush head, grip handle) if any signs of damage, please immediately stop

using.

6. Charging stand should not be used outside or near a hot surface.

7. Do not use while bathing or bathing.

8. If your mouth or gums have had surgery in the past two months, consult your dentist before using this

toothbrush.

9. If you have bleeding after using this toothbrush, or if the bleeding continues for more than a week,

consult your dentist.

10. Do not use the head of a toothbrush that is not recommended by the manufacturer.

11. If you have a heart rate regulator or other device installed, consult your doctor or the manufacturer of

the implant before using it.

12. This product is only suitable for cleaning toothbrush, gums and tongue, please do not use for other

purposes. If you feel any discomfort or pain after use, please discontinue use and seek medical assistance. If

you have medical concerns, consult your doctor before using this toothbrush.

13. This product is not intended for children under four years of age or for those who can not operate it,

unless they are under the supervision or guidance of the person in charge of safety.

14. If the toothpaste contains hydrogen peroxide, bicarbonate of Soda or bicarbonate (commonly found in

whitening toothpastes) , wash the head thoroughly with water after brushing.

Product name: sonic electric toothbrush

1.product Model: LJ-ST102

2. working voltage 100-240V / AC

3.rated power: 2w

4.switch mode: light touch

5.display mode: 1 tricolor lamp display content Sensitive, clean, whitening mode + white lamp power

indicator

6.vibration frequency :31000-47000 RPM / Min

7.working time: approximately 240 minutes (sensitive mode)

8.charging mode: induction charging (plug into universal USB charger: 5VDC) charging time about 3.5 hours

9.charging current :350mA

10.battery specification: lithium battery / ICR14500 / 650mAh

11. battery capacity reminder: low capacity, power indicator light flashing

12.WATERPROOF GRADE:IPX7

Fault diagnosis:

Situation

Possible cause

actions

The vibration is getting weaker

1. The brush is pressed against the

tooth. 2. The brush head is too

close to the body

1.Gently place the brush head on

the teeth. 2. Remove the brush

head from the handle and

reattach it to the output shaft.

Keep the brush head at a distance

Summary of content (5 pages)

PAGE 1
Please read the instruction manual of this product carefully. Warning: 1. check for any visible damage before each use. 2. Do not use if damaged or severely damaged. 3. Before you connect the power cord, check that the local power supply voltage is consistent with the voltage indicated by the product. 4. Do not use the charging stand if it is damaged in any way. 5. This product (including toothbrush head, grip handle) if any signs of damage, please immediately stop using. 6.
PAGE 2
from the handle. Even when recharged, the 1. The body is not vertically 1. If you don't have enough time toothbrush will only work for a positioned on the charger causing to recharge, keep charging This short time it not to be charged. 2.
PAGE 3
Use steps 1. The first step is to use up the remaining electricity, then charge the electric toothbrush for 3.5 hours or so until the power is saturated. 2. The second step is to carefully insert the toothbrush into the output shaft. There must be some space between the toothbrush head and the main body, which is necessary for the normal vibration of the toothbrush head. 3.
PAGE 4
Warranty service this product is a well-designed, high-quality components of the electrical appliances, in normal use and maintenance should be able to play its superior performance, in a specified period of time if any manufacturing process or components caused by damage, please contact the dealer for repair or replacement services. The following situations will not be covered by the Warranty Service: 1.
PAGE 5
The equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. During the operation of device a distance of 15 cm surrounding the device and 20 cm above the top surface of the device must be respected.