Manual of Robot Vacuum Cleaner (Dust Collection Suit) Please read this manual carefully before use and keep it properly for future reference. The power adapter of the product applies to an altitude below 2000m.
Product introduction Intelligent recharge Sh ort press the button to enable intelligent recharge. If th e ora n g e in d i ca t o r remains lit, it suggests that the Product has a low battery. Power-on/off/sweeping planning Network configuration Short press “Start/Pause” to sweep. Long press this button for 3s topower on or off. If the indicator remains lit in blue, it suggests successful network configuration, normal running or a standby state.
Product introduction Main body and sensors Laser radar Button Top cover Infrared receiving sensor Right wheel Collision sensor Charge electrode Mecanum wheel Mopping module 2 Range sensor Roller brush Side brush Roller brush cover Left wheel
Maintenance tips Only specially trained persons with a certificate for robot vacuum maintenance can maintain the Product. To avoid serious consequences, other persons should not maintain the Product without permission. If the Product has failed, please try to solve the problem with reference to Analysis and Elimination of Common Faults before contacting our customer service department. If you cannot eliminate the fault by yourself, please unplug the power cable and contact us.
Product introduction Dust collector (dust collection and recharge) Two-in-one water tank To p cover Water inlet Open the top cover to putthe dust bag in or take it out. Water tank Dust container release button Dust container buckle Dust container Dust bag chamber Mop holder Indicator Mop Dust collector’s charging electrode Infrared lens Strainer holder Dust inlet Dust in the main body is sucked into the dust bag via here.
Product introduction Installation instructions Installaiton of the dust collector 1. Put the dust collector on a flat floor by a wall and insert the power plug into a proper power socket. Put on the flat floor by a wall. Fan strainer 2. Make sure there is no barrier in front of or behind the dust collector or on any lateral side of it. Dust bag handle Dust bag Dust bag (There is already one on the dust collector) Reminder: The dust bag is a consumable. Please replace it at regular intervals.
Directions for use 1. Power-on/off Long press button“ ” for 3s for power-on: The power indicator will flash slowly in blue for 4s and then remain lit in blue, suggesting that the Product is standby. When the Product is not moving, long press button“ ” for 3s to power it off. The power indicator will then go out. = 6. Fault state When the Product has any fault, it will give a voice prompt, and the power indicator will flash quickly in red.
Directions for use Way to configure WiFi network 3. Feed clean water into the water tank. Scan the following QR code to download the APP and install it to your mobile phone as instructed on the mobile phone. 4. Mount the water tank and the mop holder into the main body in sequence. 5. Long press button“ ” for 3s to power on the Product. After that, short press button“ ”. The Product will then be recharged automatically. Upon full recharge, it will be ready for work.
Routine maintenance Cleaning of the water tank 1. Pull the water tank out while pressing the water tank release button. 3. Take out the strainer. Strainer holder Strainer 2. Pull the dust container buckle to dismount the strainer holder. 4. Use the roller brush to remove the foreign matterson the strainer and the strainer card.
Routine maintenance Roller brush 5. Feed water into the water tank, close the water tank, shake it from side to side and pour the dirty water in it. Repeat these operations till the water tank has been cleaned thoroughly. Roller brush cover Roller brush 6. Turn over the water tank, dismount the mop holder and clean or replace the mop. 2. Use a cleaning knife to cut off the hair on the roller brush and use the cleaning brush on the other end of the cleaning knife to clean up the roller brush. 3.
Routine maintenance Replacement of the dust bag Cleaning/replacement of the side brush 1. When the dust bag is full, the dust collector’s indicator remains lit in orange, or the APP reminds user to replace the dust bag in time. When the dust bag is in normal use, the dust collector’s indicator remains lit in white. 1. Dismount the side brush by removing its screws with help of a screwdriver. Dismount Open the top cover. 2. After cleaning, remount the side brush or mount a new one.
Routine maintenance Dustcollectorcharging pile: Indicator ×1 Infrared lens ×1 charge/dust collection sensor×2 Cleaning of sensors 1. It is suggested to use clean soft, dry cloth to wipe the sensors gently each week for normal use of the Product. the Product : Range sensor ×3 Charge electrode×4 Infrared sensor ×2 Infrared sensor Indicator Indicat Infrared lens Range sensor Charge electrode Charge/dust collection sensor Range sensor Battery maintenance 1.
Names and contents of hazardous substances in product Basic parameters Main body Product name robot vacuum cleaner Model L1550 C Dimensions φ325mm×325mm x 95mm Rated voltage 14.4V Rated power 35W Battery capacity 2600mAh Wireless connection Wi-Fi IEEE 802. 11b/g/n 2.4GHz Hazardous substance Component Hg Cd cr( VI) PBB PBDE Metal PCB component Plastic Standard Standard part (screw, washer and so on) The Product has a radio transmission module with a CMIIT ID:.
Troubleshooting Fault prompt Problem solution Fault 1: Inspect and make sure the laser radar is not blocked. Please inspect and remove the foreign matter(s) close to the laser radar (if any), or move the Product to another position and restart it. Fault 2: Please wipe the range sensors, move the main body to another position and restart the Product.
Cautions ·Use the Product to sweep domestic indoor floors of only. Do not use it to sweep outdoor floors (such as the floors of open balconys), places that are not floors (such as sofas), or floors in commercial or industrial places. ·Do not use the Product in any place hung in the air (such as a duplex, an open balcony or the top of a house) without guard railings. ·Do not use the Product above 40℃, below 0℃ or in a place with any liquid or sticky matter on the floor.
