User's Manual

CONTENT
01
02
04
04
15
Points for Attention
Product Overview
Specifications
Installation Filter
Function Instruction
Maintenance
FAQ
14
06
Before using, please read this user manual carefully and keep it for future reference.
1. To avoid electric shock and fire, do not allow water , liquid or any flammable detergent to get
into or to clean the product.
2. Do not spray insecticide, perfume or other flammable spray around the products.
3. Before connecting the power supply, please check whether the voltage of the product is
consistent with the local power supply voltage.
4. This product can not replace normal ventilation, daily dust collection or oil pumping when cooking.
5. Ensure the product is used in condition of a stable and horizontal level.
6. Leave at least 30cm of space on the back and sides of the product, and at least 50cm of space
above the product when using.
7. Ensure both the filter and its cover are properly installed before using.
8. Do not insert finger or other things into the air outlet/inlet to prevent physical damage or trouble.
POINTS FOR ATTENTION
PRODUCT OVERVIEW
Components
Control Panel
AIR PURIFIER
SPECIFICATIONS
INSTALLATION FILTER
ˉˉ
01
02
ˉˉ
03
ˉˉ
04
ˉˉ
06
ˉˉ
07
ˉˉ
08
ˉˉ
09
Please remove the packaging of the filter before using for the first time.
Ensure the machine is unplugged before removing or installing the filter.
When the power indicator keeps flashing in red, the filter should be replaced.
Please wipe the dust on the filter regularly, do not wash or use it repeatedly.
Please use the filter specially designed for this product.
Power Button
In the condition of working, press the wind speed button, the buzzer will ring for one time.
Press again to adjust the wind speed among the circulation of Low grade, Middle grade
and High grade with buzzer rings, the corresponding indicator will be on.
Wind Speed Button
Touch the power button to turn on the machine, the buzzer will ring for one time, the power
indicator and the low grade of wind speed indicator light turns green.
Touch the button again, the buzzer will ring for one time and the machine will turn off with
all lights turn off.
When the power is on, check the status of the WiFi indicator light, users could use this
button according to the introduction of “Works with Smart Life APP”.
ˉˉ
05
Notice
Button Operation
Steps of Installing Filter
When connect to the power socket, the buzzer will ring for 1 second.
FUNCTION INSTRUCTION
In the condition of working, press the timer button to set among the circulation of 2h and 4h
timer with buzzer rings, and the corresponding indicator will be on.
Press again, the timer indicator turns off and the machine will work continuously without
timer.
In the status of timing, the machine begins to count down. When the time is up, the fan
will stop working and all lights will be off.
Timer Button
Notice: The machine will record the working modes when turns off without
unplugging the power socket.
Notice: The timer button couldn’t operate in the status of shutdown.
Notice: The wind speed adjustment couldn’t operate in the status of shutdown.
1. Invert the machine, and rotate the base along the direction marked "OPEN".
2. Take out the filter from the machine.
3. Remove the packaging of the filter.
4. Install the filter into the machine.
5. Then Install the base, rotate and tighten the base along the direction
marked "CLOSE”.
Warning
Model No.
Size
Net Weight
Input
Power
CADR
Coverage Area
Allo
195*195*403mm
2.3kg
AC100-120V 50/60Hz
35W
90m
3
/h
≤11m
2
V1
MAINTENANCE
Notice: Please don’t drop any water into the machine when clean the air outlet.
No working
Coming out
nasty smell
The reminder of
replacing filter is sitll
flashing after user have
replaced a new one.
SITUATION
Poor performance
REASON
● Is it plugged into a power socket? Is there a power outage?
● Is the home leakage switch or fuse cut off?
● Is there any dust in the surface of pre-filter?
● Is there any obstacle blocking the air inlet/outlet.
● It is the normal phenomenon that the machine emits the smell
of plastic for the first time.
The machine will emit nasty smell if the filter is dusty, so in this
situation, please clean or replace the filter.
● If the burning smell emits from the machine, please unplug the
power socket and contact with buyer or customer service.
● Please press the power button for 7s to reset the machine
and the life counter of the filter will start.
Notice: If the above FAQ can not solve your problems and need maintenance, please contact
the supplier or after sales service center. Please do not disassemble the machine to maintain
by yourself.
Ensure the machine is power-off and unplugged.
Use a soft cloth with neutral cleanser to clean away any dust or debris from the surface of the
unit and air inlet/outlet.
After the machine completely dry out, put on the bag and place it in a cool and well ventilated
place.
If you do not use it for a long time, in the basic of previous steps, please turn on the machine
for a few minutes from time to time to ensure a good performance.
Note
ˉˉ
14
ˉˉ
15
Ensure the machine is unplugged before maintenance.
Do not immerse the into water or any liquid.machine
Do not use abrasive, corrosive or flammable cleansers (such as bleach or alcohol) to clean
any part of the unit.
Don't use a vacuum cleaner to clean the filter or wash it directly.
Please sterilize the filter under sunlight regularly.
Cleaning & Storage
Significant noise
● Is there anything stuck on the fan in the air outlet?
● Is the machine tilted?
● Please set a lower grade of wind speed if the noise is too loud ,
or set low grade of wind speed when using in bedroom at night.
● Is the filter replacing indicator keep flashing?
1. Download & Registration
Smart Operation Instruction
Works with smart life APP
Scan the QR code to download “Smart Life” APP. You can also search “Smart Life” in either
APP store or Google Play to install the APP.
Open the “Smart Life” APP, tap “Register” to register a “Smart Life” account with your phone
number or E-mail. Then sign in the APP.
2. Add Devices in Easy Mode (Recommend)
Make sure your smart device is energized and your mobile phone is connected to your WiFi
network. If the WiFi indicator of smart device keeps flashing to indicate that the smart device
enters the mode of configuring the mobile phone; if not, please press the Power button for
more than 7 seconds, after hearing the smart devices “beep”, then loose it and this means
the device is already for configuration.
Open your “Smart Life” APP and tap ”+” on the top right of the APP. Select type of service
device, tap “All devices” and turn to “ Add Device”, then automatically fetch the password
of the WiFi network that your mobile phone connects to. Then tap “OK” to connect to the
device.
ˉˉ
10
ˉˉ
11
When appearing “Successfully added 1 device”, it means the connection is complete and
your device will be listed in your APP list.
3. Add Devices in AP Mode
If failed in Easy Mode, users could also add devices in AP Mode.
Press the Power button for more than 7 seconds until hearing “beep”and the WiFi indicator
light begin to flash quickly, then press the Power button for another 7 seconds until hearing
“beep”and the indicator light begin flash slowly, this means the device is already for
configuration in the AP Mode.
Tap “+” on the top right of the APP. Select Device Type and tap it. Then select “AP Mode”
on the top right of the APP. Tap “Connect now” to go to the WLAN Settings interface in your
mobile phone and select the WiFi network named “Smart Life_XXXX” to connect it.
Return to the “Smart Life” APP, the connection will start automatically.
When appears “Successfully added 1 device”, it means the connection is complete and
your device will be listed in your APP list.
Now you can control your smart device via your mobile phone APP anytime and anywhere
(Make sure your mobile phone and smart device are all connected to the network). You can
share your devices with your friend or family after you add your devices successfully.
4. Q&A
(1) Why failed in adding device?
a.Make sure the device is powered on and close to your mobile phone when adding device.
b.Make sure your mobile phone is connected to the WiFi network and your WiFi router is
working properly.
c.Make sure the device is ready for configuration.Please refer to the Product Instruction
“Add Devices in Easy Mode” or “Add Devices in AP Mode” for details.
d.Make sure the connected devices have not reached the maximum number of WiFi router.
If not, please disconnect the network of some devices.
e.Make sure password of the WiFi network is correct when adding new device.
f.Make sure you have not used any Chinese Characters to name your WiFi network.
(2) Can I control device with 2G/3G/4G/5G network?
When adding device for the first time, it requires that your mobile phone and device are
connected to the same WiFi network. After adding device successfully, you can remote control
your device with 2G/3G/4G/5G network.
(3) How can I share my device with others?
Open your Smart Life APP, select your device and tap the button in the top right corner. Tap
“Shared devices” and “Add sharing”, then select the “country/region” where the account belongs
to and input the “Account number”(a phone number or an E-mail address) you want to share
with. (Please make sure the phone number or E-mail is registered.)
(4) How can I manager the device shared by others?
Open your Smart Life and you can operate the device by tapping the product in the "Shared
device I received" on the home page.
(5) How to remove device?
Method 1: Press the Power button for more than 7 seconds, you will hear “beep”, it means the
device is removed, and the WiFi indicator light begin to flash quickly again.
Method 2: Open your “Smart Life” APP, select your device and tap the button in the top right
corner. Tap “More”.Then tap the “Remove Device” in the bottom, the WiFi indicator light begin to
flash quickly again.
1. What you need to get started
Works with Echo
Before using Echo to control your smart devices, make sure you meet the following conditions.
√ Stable WiFi network which could access to Amazon server. (For mainland China users)
√ An Echo device, including Echo, Echo Tap, or Echo Dot.
√ An Amazon account.
√ Smart Life app and a related account.
√ Smart devices.
2. Add devices in Smart Life app (Refer to App Instruction)
You can skip this part if you've already add some devices to your Smart Life account, and in the
meantime the devices' name are easily recognized.
(1) Download Smart Life app (Refer to App Instruction)
You can scan the QR code below to download the Smart Life app
You can also search "Smart Life" in either App Store or Google Play to install the app.
(2) Register a Smart life account and sign in the app (Refer to App Instruction)
Open the Smart Life app, tap "Register" to register an account, then sign in the app.
ˉˉ
12
ˉˉ
13
(3) Add device and change device's name (Refer to App Instruction)
Sign in with the Smart Life account, add the device, then change device name to a easily
recognized word or phrase, like "Allo".
3. Set up Amazon Echo and enable Smart Life Skill
We suggest using web for configuration in mainland China since Alexa app is not available here.
User can configure Echo through web or Alexa app.
Web configuration link: http://alexa.amazon.com/spa/index.html
Search "Amazon Alexa" in App Store or Google Play to install the app.
We take app configuration as an example. Configuration through web and app are basically the
same.
(1) Set up Echo with Alexa app
You can skip this part if your Echo is already set up.
1. Make sure your Echo device is energized.
2. Open the Alexa app by tapping the app icon on your mobile device.
3. Type in your Amazon account and password, then tap "SIGN IN".
4. Tap the hamburger menu on the top left corner, select "Settings", then tap "SET UP A NEW
DEVICE".
5. Select your Echo model, choose a proper language, then tap "CONNECT TO WI-FI".
6. Long press the dot button on the top of your Echo device until the orange light shows up, then
tap "CONTINUE". When your phone is connected to Echo, tap "CONTINUE".
7. Select a Wi-Fi to let Echo have the access to the internet. Type in the Wi-Fi password, then tap
"CONNECT". Echo may take several minutes to connect the network.
8. Tap "CONTINUE" when Echo is connected to the network. After an introduction video, tap
"CONTINUE" to finish the setup.
(2) Link Smart Life account to Alexa
1. Tap "Skills" in the hamburger menu, then search "Smart Life". Select "Smart Life" and tap
"ENABLE" to enable the Skill.
2. You will be redirected to the account link page. Type in your Smart Life account and password,
don't forget to select the country/region where your account belongs to. Then tap "Link Now" to
link your Smart Life account. The country/region, the account, and the password must match
with the exact content in Step 2.(2)
4. Control your smart devices through Echo
(1) Discover devices
Echo needs to discover your smart devices before it controls them. You can say "Alexa, discover
devices" to Echo. Echo will discover devices which have already been added in the Smart Life app.
You can also tap "DISCOVER" to discover the smart devices. Discovered devices will be shown
in the list.
Note: every time you change the device's name on Smart Life app, Echo must re-discover before
you control them.
(2) Control devices by voice commands
Now you can control your smart devices through Echo. You can use the following commands to
control your devices:(e.g.: device’s name: Allo)
▶Alexa, turn on/off Allo
▶Alexa, set Allo to one(low mode)
▶Alexa, set Allo to two(middle mode)
▶Alexa, set Allo to three(high model)
Notice: Alexa could just support function of on/off and wind speed.
h
h
h
M
AIR PURIFIER
Model:Allo
Control Panel
Air Outlet
Body
Air Inlet
Filter
Base
h
h
M
Power Button
Timer Button
Wind Speed Button
Reminder of Replacing Filter
2h-4h-
Timing&WiFi Indicator Light
H-M-L
Wind Speed Indicator Light
CLOSE
OPEN
2
Filter
Packaging
Filter
step 2
step 3
step 4
step 5
CLOSE
OPEN
step 1
Reminder of Replacing Filter
When the accumulated operation of the air purifier reaches 2200 hours, the indicator
flashes red; the new filter is required to be replaced. After replacing the new filter, press and
hold the power button for about 7 seconds to release the alarm.
Notice: Users do not need to reset when using the machine for the first time after
installing the filer.
FCC warning：
ˉˉ
16
ˉˉ
17
Any Changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
Note
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
-Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment.
This equipment should be installed and operated with minimum distance 20cm between the
radiator & your body.
16
FCC warning