GTRAN Wireless, Inc. CDMA 1X 1900MHz User Manual Version: 0.
GTRAN Wireless, Inc. 2001 GTRAN Wireless Inc. All rights reserved No reproduction in whole or in part is permitted, without prior written approval. GTRAN Wireless Inc. and DotSurfer are registered trademarks of GTRAN Wireless Inc.
GTRAN Wireless, Inc. 1. DOTSURFER® 1X-1900 INTRODUCTION.......................................................................................4 2. INSTALLATION FOR WINDOWS 98, 2000, AND ME.....................................................................4 3. USING GT DIALER ..............................................................................................................................6 3.1 MAIN SCREEN AND ICONS................................................................................
GTRAN Wireless, Inc. 1. DotSurfer® 1X-1900 Introduction GTRAN Wireless DotSurfer® 1X-1900 is a high-speed wireless Type II PCMCIA modem card that fits into major laptops and PDAs. Allowing for wireless Internet connectivity under CDMA2000 network, DotSurfer 1X-1900 delivers unmatched speed at up to 153Kkbps. At 86 mm in length, DotSurfer is small, compact and inserts perfectly into a laptop or PDA and has a flexible antenna applicable for all mobile users.
GTRAN Wireless, Inc. e. Select your choice under the System Reboot screen. f. Insert the DotSurfer 1X-1900 modem card into the PC slot of your laptop. Make sure that the installation CD is still in the laptop. Your Windows will automatically search for and load a device driver for the DotSurfer modem card and you will see the screen below. Once the device driver is loaded, the screen will disappear. * For WINDOWS 2000, you’ll see the following Digital Signature Not Found screen. Click the Yes button.
GTRAN Wireless, Inc. g. Now the DotSurfer 1X-1900 modem card is ready for use! 3. Using GT Dialer Insert the DotSurfer 1X-1900 modem card into your notebook computer. To run GT Dialer, double-click GT Dialer icon from the desktop or go to Start and select Program-> GTRAN-> GT Dialer. 3.1 Main Screen and Icons Main screen shown below will appear once the GT Dialer is opened.
GTRAN Wireless, Inc.
GTRAN Wireless, Inc. 3.2 Network Connection To connect to network, open the GT Dialer and click the Connect/Disconnect button. To disconnect, simply click the Connect/Disconnect button again. 3.3 Internet Connection Establish network connection by clicking Connect/Disconnect from the main screen. By clicking the Internet icon, you will go to a web browser. To change the default website which is set up under the Internet icon, click Setting and enter the desired website URL. 3.4 SMS 3.4.
GTRAN Wireless, Inc. Previous Message Next Message New Message Old Message REPLY Replies to sender DELETE Deletes the message BACK Goes back to the main window 4.4.3 Sent Messages (Sent Box) Click Sent Messages button from the main screen. Previous Message Next Message SEND Sends or resends a message DELETE Deletes a sent message DELETE ALL Deletes all sent messages in the Sent Box BACK Goes back to the main window 3.
GTRAN Wireless, Inc. Previous Address Next Address Click to send SMS from Address Book. This screen is the same screen as the one you get from clicking Write Messages from the main screen. The method of sending messages is also same. Click to send email from Address Book. Clicking the icon will take you to the new message in Outlook Express. 3.5.1 Search Address Book You may search by name, by phone number, by e-mail, by index number, 3.5.2 Add to Address Book a. From Address Book screen, click NEW.
GTRAN Wireless, Inc. Select the address to delete and click DELETE. 3.6 Screen Graphic, Sound, SMS Pop-up Window, and Connection Set Up a. From the main screen, click which is at the bottom of the screen. Screen shown below will appear. Enter the appropriate information to customize your settings. Visual appearance of the GT Dialer Default URL when you click to connect to the Internet. b. If you do not know your User ID and Password, please consult your wireless service provider.
GTRAN Wireless, Inc. 3.7 Color Set Up This feature is to change the outline color of your GT Dialer. a. Click b. Click Change color… and select the color you want which is at the bottom of the main GT Dialer screen. Do not set the color to black. You won’t see some of the buttons on the screen. c. Click OK. The outline color of the GT Dialer screen will change. 3.8 Detailed Connection Information Click at the bottom of the main GT Dialer screen and you will see a screen as shown below.
GTRAN Wireless, Inc. Click here to reset and start a new tracking session. Total Time: Total time connected since last tracking OUT: Transferred packet size from the last connection session IN: Received packet size from the last connection This Month: Total time connected this month Last Month: Total time connected last month Usage information is an estimate only and may vary depending on your carrier’s billing policies. 4. GT Indicator GT Indicator Program is a supplemental program for GT Dialer.
GTRAN Wireless, Inc. c. To read SMS, Click and you’ll see a screen shown below.
GTRAN Wireless, Inc. 4.2 GT Indicator Icons RSSI Status Indicator Icon No service Signal strength (RSSI) CONNECTION Status Indicator Icon Modem is connected to network Modem is disconnected from network Modem is in dormant mode ROAMING Status Icon Roaming off Roaming SMS Dialog Box Viewer Icon No new SMS message New SMS message Click the icon to read SMS messages GO to Web Page Search Icon Goes to selected URL page 5. Windows CE (Pocket PC Procedures) 5.1 Installation for COMPAQ iPAQ a.
GTRAN Wireless, Inc. are synchronized, you should see the screen shown below on your PC. c. Insert DotSurfer installation CD into your PC. Click Cancel on the following screen. d. Go to Start -> Programs -> Windows Explorer -> D:\ -> WinCE -> Sa1110 -> setup.exe, where D is the driver for CD-ROM. e. Follow the on-screen instructions. f. On the screen asking to install Default Installation Folder, click Yes.
GTRAN Wireless, Inc. g. When installation is complete, screen will appear as shown below. Click OK and the installation automatically will run in iPAQ PDA. h. When the synchronization is complete, take out the iPAQ from the cradle. Attach the PC card expansion pack onto the PDA and insert the DotSurfer® CDMA 1X card into the PC card slot. i. Using iPAQ’s stylus, press the reset button on the right bottom of the PDA. 5.2 Connecting to Internet a.
GTRAN Wireless, Inc. b. When you see the screen below, input user ID, password, etc. and click Connect. c. Once connected, go to Start –> Internet Explorer and start surfing the web. 5.3 GT Dialer User Manual Go to Start –> Programs -> GT Dialer. Screen showing DotSurfer® 1X status will appear.
GTRAN Wireless, Inc. < Before connection> Receiving signal strength New SMS message received Card connection status 5.3.1 Send and Read SMS Messages a. Click Message tab on the bottom of GT Dialer main screen. b. To send an SMS message, click New button on the bottom and create a message.
GTRAN Wireless, Inc. c. Input the destination number and text message and click Send button. d. To read an SMS message, double-click the message. 5.3.2 Delete, Reply, Forward SMS Messages a. To delete an SMS message, select the message. Using the Stylus, tap and hold, which will display the pop-up menu. Select Delete from the pop-up menu. b. To reply to the received message, select the message and with the Stylus, tap and hold. Select Reply from the pop-up menu. c.
GTRAN Wireless, Inc. b. To add new number, click New button, input the info and click Save. c. To search for the phone number or string from your contact list, click Search button. number or string and click OK button.
GTRAN Wireless, Inc. d. To send an SMS message to a person listed under contact list, select a contact with the stylus by tapping and holding. Select Send SMS or Send E-Mail from the pop-up menu. e. To edit a contact from the list, click Edit from the pop-up menu and edit. f. To delete a contact from the list, click Delete from the pop-up menu 5.3.4 Other Displays From GT Dialer main screen, click Tool -> Information -> Time. - Go to Tool -> Information -> Time to access Connection Time display.
GTRAN Wireless, Inc. Total used: Total time used prior to resetting the accumulated time This Month: Accumulated time for this month Last Month: Accumulated time for last month - Go to Tool -> Information -> Transfer Packets to display Transfer Packets status. Card displays the transfer packets. A packet size defines to 512 bytes. OUT: Received packets during connection IN: Sent packets during connection From GT Dialer main screen, click Tool -> Setting.
GTRAN Wireless, Inc. - To select a method of receiving, go to Tool -> Setting -> Message. If inbox is full, select Rejected new msg and select Deleted the oldest & stored new msg. - To select Message Alert sound, go to Tool -> Setting -> Sound. Choose a wav file and click OK button.
GTRAN Wireless, Inc. - To go to Connection Setting, click Tool -> Setting -> Connect. Use set value as is, with the exception of certain cases. The battery life on your iPAQ or Pocket PC device will be affected by the use of your DotSurfer® card. 6. LINUX Procedures To access the manual for Linux based software installation procedure, go to www.gtranwireless.com. Appendix A: Updating the GT Dialer (GT Updater) GT Updater is a unique application included in the DotSurfer software suite.
GTRAN Wireless, Inc. e. Select the components to be updated and click Update. f. Once update is completed, the update results will be shown in the Status column. g. Exit the GT Updater and reboot the computer. Appendix B: Product Specifications System Requirements Card Slot 1 Type II PCMCIA Computer 5 Mb’s free hard drive space, 32 Mb of ram & a CD-ROM Operating Windows Windows Windows Windows Windows Windows Linux System 95 98 ME 2000 NT CE* (See www.gtranwireless.
GTRAN Wireless, Inc. Receive Frequency 1930 MHz- 1989.950 MHz Channel Spacing 45 MHz Frequency Stability +/- 300Hz Appendix C: Safety and Regulatory Information Safety and Hazards DotSurfer modem card should not be used in any environment where radio frequency equipment is restricted or prohibited to be in use. This includes airports/aircrafts, hospitals, and other areas susceptible to any form of radio interference.
GTRAN Wireless, Inc.
