Instruction Manual

Factory Defaults
NOTE: Set up documents (80090) can and will override this list.
Current Same as ROM Defaults
MENU BITS RECALL ->
1
2
MENU BITS RECALL ->
1
2
M1.7 A[01] MODE 1 bank a
M1.6 A[02] MODE 2
M1.5 A[03] INC VALUE 1
M1.4 A[04] INC VALUE 2
M1.3 A[05] PROMPT
M1.2 A[06] DATA RATE 1
M1.1 A[07] DATA RATE 2
M1.0 A[08] DATA RATE 3
0
1
0
0
0
0
1
1
1
0
0
0
0
1
0
0
M5.7 B[15] MOUSE 1
M5.6 B[16] MOUSE 2
M5.5 B[17] HIGH/LOW PROXIMITY
M5.4 B[18] CTS LINE ENABLE
M5.3 C[01] PORTRAIT 0 bank c
M5.2 C [02] CR DISABLE
M5.1 C[03] BEEP ON PEN DOWN
M5.0 C[04] DISABLE BEEPER
0
0
0
0
0
0
0
0
0
0
0
1
0
0
1
0
M2.7 A[09] RESOLUTION 1
M2.6 A[10] RESOLUTION 2
M2.5 A[11] RESOLUTION 3
M2.4 A[12] FORMAT 1
M2.3 A[13] FORMAT 2
M2.2 A[14] FORMAT 3
M2.1 A[15] FORMAT 4
M2.0 A[16] FORMAT 5
1
1
0
1
1
1
1
1
1
0
0
1
1
1
1
0
M6.7 C[05] TILT TO PRESSURE
M6.6 C[06] PORTRAIT 1
M6.5 C[07] TOP ORIGIN
M6.4 C[08] 9500 style cursor
M6.3 C[09] RESERVED
M6.2 C[10] RESERVED
M6.1 C[11] RESERVED
M6.0 C[12] RESERVED
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
M3.7 A[17] LF ENABLED
M3.6 A[18] 7 OR 8 DATA
M3.5 B[01] BAUD RATE 1 bank b
M3.4 B[02] BAUD RATE 2
M3.3 B[03] BAUD RATE 3
M3.2 B[04] PARITY 1
M3.1 B[05] PARITY 2
M3.0 B[06] PARITY 3
1
0
0
0
1
0
0
1
1
1
0
0
1
0
0
0
M7.7 C[13] L_COMMANDS
M7.6 C[14] McD spr
M7.5 C[15] Auto/tek/lectra spr
M7.4 C[16] jccs
M7.3 C[17] otsuka
M7.2 C[18] lectra large format
M7.1 ?[??] DISABLE FUNCTION B
M7.0 ?[??] CMENU_ACTIVE
0
0
1
0
0
1
1
1
0
0
0
0
0
0
0
0
M4.7 B[07] FREQUENCY
M4.6 B[08] NO MM OR 2000
M4.5 B[09] MUST USE ESC 9X00
M4.4 B[10] PROXIMITY
M4.3 B[11] PPEN
M4.2 B[12] HEIGHT
M4.1 B[13] TILT_DATA
M4.0 B[14] TILT_CORRECT
0
1
1
0
0
0
0
1
0
0
0
0
0
0
0
0
recall 1 43, DF, 89, 61, 00, 00, 27
recall 2 84, 9E, C8, 00, 12, 00, 00
X is the last value, i.e. It does not
change these bits.