Configuration Use switch six to flag Switch Settings 0 is on (closed) SWITCH 654321 XXX000 XXX001 XXX010 XXX011 XXX100 XXX101 XXX110 XXX111 XX1XXX XX0XXX X1XXXX 1XXXXX 0XXXXX ROM Defaults TYPE FORMAT MODE PARITY BAUD RESOLUTION DATA RATE RECALL 1 RECALL 2 Determination Summagrid (used for old board/software) 1 is off (open) SIZE XxY reserved (12 x 12) reserved (12 x 18) reserved (18 x 24) reserved (tbd) 36 x 24 48 x 36 60 x 44 reserved (high accuracy only) high accuracy standard surface (default) back li
Factory Defaults NOTE: Set up documents (80090) can and will override this list. Current Same as ROM Defaults MENU BITS RECALL -> M1.7 A[01] MODE 1 bank a M1.6 A[02] MODE 2 M1.5 A[03] INC VALUE 1 M1.4 A[04] INC VALUE 2 M1.3 A[05] PROMPT M1.2 A[06] DATA RATE 1 M1.1 A[07] DATA RATE 2 M1.0 A[08] DATA RATE 3 M2.7 A[09] RESOLUTION 1 M2.6 A[10] RESOLUTION 2 M2.5 A[11] RESOLUTION 3 M2.4 A[12] FORMAT 1 M2.3 A[13] FORMAT 2 M2.2 A[14] FORMAT 3 M2.1 A[15] FORMAT 4 M2.0 A[16] FORMAT 5 M3.7 A[17] LF ENABLED M3.
Firmware Output Formats
Binary Formats 30 Format 7 6 1 1 PR 2 0 X6 3 0 X13 4 0 Y6 5 0 Y13 6 0 p6 5 T0 X5 X12 Y5 Y12 p5 4 X14* X4 X11 Y4 Y11 p4 30 Format DELTA 7 6 5 4 1 1 PR T0 X14* 2 0 X6 X5 X4 3 0 Y6 Y5 Y4 3 Y14* X3 X10 Y3 Y10 p3 4 0 C4 X4 X10 X16 Y4 Y10 Y16 3 T2 C3 X3 X9 X15 Y3 Y9 Y15 2 C2 X2 Y2 1 C1 X1 X8 Y1 Y8 p1 0 C0 X0 X7 Y0 Y7 p0 PR 0=IN PROX 1=OUT OF PROX X14* AND Y14* are set high (1) for + and low (0) for Ä OR X14,Y14 NOT Pressure enabled 0 to 127 0 C0 X0 PR 0=IN PROX 1=OUT OF PROX Y0 X14* AND Y14* are set hi
31 Format 7 6 1 0 1 tg2 0 0 3 0 0 4 0 0 5 0 0 6 0 0 7 0 0 8 0 0 9 0 0 10 0 0 11 0 0 5 0 0 X5 X11 0 Y5 Y11 0 P5 P11 0 4 0 C4 X4 X10 X16 Y4 Y10 Y16 P4 P10 P16 3 T2 C3 X3 X9 X15 Y3 Y9 Y15 P3 P9 P15 2 T1 C2 X2 X8 X14 Y2 Y8 Y14 P2 P8 P14 1 T0 C1 X1 X7 X13 Y1 Y7 Y13 P1 P7 P13 Cursor Coding Pen Lectra 31 up 00000 tip (0) 00001 sw1 00010 sw2 00100 0+1 00011 0+2 00101 1+2 00110 0+1+2 00111 Pen up tip (0) sw1 sw2 0+1 0+2 1+2 0+1+2 31 00000 00001 00010 00011 00001 00101 00110 00001 3, 29 and 30 0 1 2 3 3 3 3 3
4-Button Cursor up 0 1 2 3 0+1 0+2 1+2 0+1+2 0+3 1+3 0+1+3 2+3 0+2+3 1+2+3 0+1+2+3 16-Button Cursor up 0 1 2 3 4 5 6 7 8 9 A B C D E F 31 00000 00001 00010 00011 00100 00001 00101 00110 00001 00001 00010 00001 00011 00001 00010 00001 31 00000 00001 00010 00011 00100 00101 00110 00111 01000 01001 01010 01011 01100 01101 01110 01111 10000 3, 29 and 30 0 1 2 3 4 3 3 3 3 5 6 7 7 7 7 7 3, 29 and 30 0 1 2 3 4 5 6 7 0 1 2 3 4 5 6 7 0 15 and 16 00 01 02 03 04 01 05 06 01 01 02 01 03 01 02 01 15 and 16 00 01 02 0
Commands (RS-232): One Byte Command for All Modes NOTE: These one byte commands cannot be inhibited by the one byte command enable menu bit. MM Commands (Must have one byte command enabled) NOTE: These commands work in both MM and 2000 mode/formats. NOTE: Do not write drivers using these to be 2x00 and 9x00 compatible. NOTE: These commands can be inhibited by the one byte enable menu bit. NOTE: Use these commands only when in MM mode/formats. It can be inhibited by the one byte enable menu bit.
rxxyy set new res xx/XSIZE=lpi and yy/SIZE=lpi (Use only on size <24 inch) max res is 1000 lpi t do self-test w send self-test results x send check sum nul 0 1 @ A B D E F G I (t 0 0 0 pr d c a) .
Micro Grid Commands ESC Z Reset Tablet. Reconfigure Base of Switches.
ESC C 3 ESC C 4 ESC C 5 ESC C 6 ESC C 7 ESC C 8 ESC C 9 ESC C A ESC C B SET RESOLUTION TO 1016 LPI, 40 LPmm SET RESOLUTION TO 500 LPI SET RESOLUTION TO 508 LPI, 20 LPmm SET RESOLUTION TO 400 LPI SET RESOLUTION TO 100 LPI SET RESOLUTION TO 1 LPI SET RESOLUTION TO 2 LPI SET RESOLUTION TO 4 LPI SET RESOLUTION TO 4096/LONG AXIS ESC T 0 ESC T 1 CLR TABLET ID SET TABLET ID ESC t ESC a ESC G ESC w DO SELF TEST SEND SIZE PROMPT COMMAND SEND SELF TEST 7 6 5 4 3 2 1 0LSB PX01XX11 | | +------- DIGITAL TEST 0=ERRO
ESC w SEND SELF TEST 7 6 5 4 3 2 1 0 LSB PX01XX11 | | +------- DIGITAL TEST 0=ERROR | +---------- PROX (1= IN 0=OUT) +------------------- TOTAL ERROR FLAG ESC CS ESC CB ESC CD ESC MP1 ESC MP0 ESC MR ESC ML ESC MA ESC MB ESC M5 ESC F3 ESC F4 ESC F5 ESC r h ESC B n 2000LPI 80 LPMM (NOT 4096/AXIS) 100 LPMM PRESSURE DATA NO PRESSURE DATA TOGGLE CR ON/OFF TOGGLE LF ON/OFF ASCII (#15) BIN (#31) ABSOLUTE ORIGIN UPPER LEFT ORIGIN LOWER RIGHT ORIGIN UPPER RIGHT change reset character mg mode n set baud rate n= 0 t
ESC d0 ESC d1 NO DEC POINT IN ASCII USE DEC POINT IN ASCII ESC g RESEND LAST DATA POINT ESC W0 ESC W1 SEND IN PROX ONLY SEND OUT OF PROX ONLY ESC Y1 ESC Y2 ESC Y3 ESC Y4 LOW TONE MED TONE HIGH TONE HIGHER TONE ESC MT0 ESC MT1 DISABLE BEEP ENABLE BEEP ESC PXhhhh SET X RES TO 0001 TO 2540 LPI ESC PYhhhh SET Y RES TO 0001 TO 2540 LPI ESCx SKEW CORRECTIONS (NOTE: MAY BE ADDED AT A LATER TIME) ESC UC SEND ID ID=SP 0 0 CR LF ESC U2 SEND CHECK BYTE IN HEX CNTL E SNE PRODUCT ID SUMMAGRID 5 ESC U E
MM Commands zi SEND INC VALUE 000 TO 255+1 z ? send product id or firmware id zt send transducer type CURSOR OR STYLUS May Need to Add Test Command at Later Date ZS0 WIRE DUMP ZS4 RAM TEST Format 15
