dint For Bailiff sie Lion NINA batteries ¢ ie Benetton pres bun. y Shs shies 45 rR HEE SR nit alliteration mes Ci » Chigger Por: BE IOWA JAC 100W « Siege Current: MAX. 104°2 vi Thanks for purchasing GT Power Mining Charger, This Is a charger with bully in microprocessor and newest program. This charger can support 2 channels charging, can charge 2 different battery types at the same time. This charger with fashion design, easy to operate. Please read the manual completely and carefully before using.
Contents 2.The exterior appearance 4 3. Warnings and safety notes A Program fifteenth § 5. Charging Current setting... 7 6. Power Allocation 7 7.Lithium Battery {LILo/LiFo/LiFe/LiHv} Made Instruction. 8. Operation process... 9. Coll Me Tor test PIROGI 10 11. Load data setting... vee M1 12. Usersatting 13. Naming and error messages . 3 4.
The charger and the battery to be charged should be set up ona heat resistant. non-flammable and non-conductive surface. + Please ensure that the fan and vents of the charger are not blocked by the surface that It displaced on. Make sure you understand the comet settings to use for the battery to be charged or discharged.
You have to know the battery allowable maximum charge current before charging. Charge ‘current exceeds the allowable maximum charge current may cause damage to battery and Its possible to lead a fire and explosion af battery when charging, We usually use C value to mark battery charging/discharging capability The battery allowable maximum charging current Is calculated by multiply C value by battery capacity.
Under DC Input mode, each channel can charge under maximum power 100W, Improve charging efficiency and shorten charging time. 7. Lithium Battery (Lit o/LiPo/LiFe/Lilv) Mods Instruct] Charging Lithium battery at balance mode “This is for balancing the voltages of Lithium batteries of the battery pack to be charged. inner system will monitor each cell's voltage and restraint each cells current to fulfill balance charging.
Press STOP key Back to the ast Interface, then press ENTER key to the next menu, Choose the right program, press ENTER key to choose balance charging mode or fast charging mode enter into next program, back press STOP key. Shortly press ENTER key to current setting. Through press INC/DEC key to set current, range from shortly press ENTER key again, then through press ING/DEC key to set battery After finished, long press ENTER key to charging program.
EES Ta This charger with bully-in high-bit micro-processor, can be used as a cell meter,t can show the voltage of each cells, the total battery pack voltage and the highest/iowest voltage. Choose the cell meter program Interface, press STAT to enter, Press START key to show the highest/lowest voltage of the single cell and the total voltage of the battery pack, press STAT to show 1-4 cells voltage, Press STOP key back ‘to man menu.
This program calls back the data that was stored at ‘Save Data program. To load the data, press Start/Enter key once to blink the data number fiend and select the number using INC of DEC key then press Start/Enter key for more than 3 seconds. As indicated, choose [61] NIGH, will show corresponded value 14AVIO0OMA ‘When you used It for the first time, kt will operate according to the preset value. You can modify parameters in the Settings column for the second time use.
Safety time setting If you tum on safety timer, safety timer wil start timing when charging. system fault or system cant identify battery capacity already full, this safety time set can stop battery being over charged. The safety time should not shorter than the time battery fully charged, usually from minim to 720min. Ca parity cut-off program Ca parity cutoff program set the maximum charging capacity.
allocation, Firmware upgrade Press ENTER key to do firmware upgrade Po war Allegation Under AC power supply, you can choose the power allocation mode, intelligent allocation or average First priority: Intelligent allocation. Dynamic Mode: average allocation. twill show the Error Information with a beep sound when operation error, 1.{" BATTERY CONNECT ERROR } Interruption of battery and output end, or the charger wire has not been connected well when charging or discharging 2.
