Technical Specifications

ManualsBrandsGT Lite ManualsLight BulbsGT-Lite Motion Activated LED Bulb — 2500 Lumens

- When using product, basic precautions should always be followed.

- Read and follow these instructions and observe all warnings.

- Carefully read and understand the information given in this manual

before beginning installation. Failure to do so could lead to electric

shock, fire, or other injuries which could be hazardous or even fatal.

- Save these instructions and warnings.

This product may present a possible shock or fire hazard if improperly

installed or mounted. Products should be installed following these instructions,

local electrical codes, and the current National Electric Code (NEC).

- NEVER submerge this product in water!

- Do not install this bulb in places where water accumulates.

- Do not use in on hot surfaces.

- Do not remove the lens protecting the LED.

- Do not use in areas near a gas source.

- It is NOT possible to change the LED light source.

- This light is not intended for use in potentially explosive

environments. This is NOT a vapor proof light.

- This bulb is NOT A TOY and is not suitable for use by children.

WARNING

CAUTION

Installation: GT-BU-2500 | 2500LM/26W Motion Detecting LED E26 Bulb

Complete LED Lighting Solutions

WARNING:

TO AVOID RISK OF ELECTRICAL SHOCK,

SHUT OFF POWER BEFORE

INSTALLING OR SERVICING THIS FIXTURE

Lumen: 2500LM

Watts: 26W

Equivalent to 150W Incandescent

LED Lifespan: 25,000 Hours

Operating Voltage: 120V AC

CRI: 80

Color Temp (CCT): 5000K Daylight

Base: E26 / Standard Edison Base

Wet Rated for Outdoor Use

Sensitivity: Detects motion up to 27ft

diameter when mounted at 10ft height.

Operating Temperature: 14°F to 104°F

(-10°C to 40°C)

This bulb is not compatible with H.I.D. fixtures or any other ballasted fixtures.

A: Motion

Sensitivity

B: Time Setting

C: Light

Sensitivity

D: Motion

Sensor

E: Adjustable

Panels (4)

Summary of content (4 pages)

PAGE 1
WARNING: TO AVOID RISK OF ELECTRICAL SHOCK, Complete LED Lighting Solutions SHUT OFF POWER BEFORE INSTALLING OR SERVICING THIS FIXTURE Installation: GT-BU-2500 | 2500LM/26W Motion Detecting LED E26 Bulb WARNING Lumen: 2500LM Watts: 26W Equivalent to 150W Incandescent A: Motion LED Lifespan: 25,000 Hours Sensitivity Operating Voltage: 120V AC B: Time Setting CRI: 80 C: Light Color Temp (CCT): 5000K Daylight Sensitivity Base: E26 / Standard Edison Base D: Motion Wet Rated for Outdoor Use Sensor Sensitiv
PAGE 2
Installation: GT-BU-2500 | 2500LM/26W Motion Detecting LED E26 Bulb ADDITIONAL WARNINGS: - Do not dismantle this light. There are NO replaceable LEDs or serviceable parts. - Do not install this light inside of undersized enclosures. - Suitable for fixtures rated for temperatures ranging from -4˚F to 113˚F. - Not Suitable for enclosed fixtures. - Not for use on HID fixtures. - Not for use on ballasted fixtures. - Do not use where exposed to standing water.
PAGE 3
Installation: GT-BU-2500 | 2500LM/26W Motion Detecting LED E26 Bulb INSTALLATION INSTRUCTIONS: 1. Before installing the bulb, shut off power supply at the circuit breaker panel to avoid electrical shock. It is recommended that surge/lightning protection be installed. This bulb is not compatible with any ballasted fixture. 2. Remove old bulb. 3. Screw in new LED Motion Detecting bulb. (Lamp should be mounted with motion sensor (D) facing down* towards the area where motion will occur.
PAGE 4
Installation: GT-BU-2500 | 2500LM/26W Motion Detecting LED E26 Bulb INSTALLATION DIAGRAM: L L E26 CFL (Neutral) N 120VAC N (Live) 120VAC (Live) (Neutral) E26 LED Bulb TROUBLESHOOTING GUIDE: Problem Probable Cause Solution Fixture does not turn on. Bad connection. Faulty switch. Power is off. Check wiring connections. Test switch or replace it. Verify power supply is on. Circuit breaker trips or fuse blows when light is turned on. Discontinue use immediately.