User's Manual

ManualsBrandsGS Instech ManualsElectronicsIn-Building Repeater

Version 1.0 * May 2011

SpeedCell Repeater

INSTALLATION GUIDE

Ver. 1.0

G06$03')8635

GDR-89192630-SPR

Summary of content (66 pages)

PAGE 1
Version 1.0 * May 2011 SpeedCell Repeater INSTALLATION GUIDE Ver. 1.
PAGE 2
Version 1.0 * May 2011 SpeedCell Repeater G06 $03 ')8 635 Installation Guide Ver. 1.
PAGE 3
Version 1.0 * May 2011 Contents of Box Contents Picture Quantity SpeedCell Repeater System Power Cord 5.9ft (1.8m) 1EA Ethernet Cable 6.6ft (2m) 1EA 1EA Lag Screw 1/2” x 2” 8EA 1EA Data cable for 2600 AMP and DFM 2 2EA 1EA Ground Sems Screw M4 x 8mm 8EA 1EA Mounting Sems Screw M6 x 10mm 12 EA 1EA Mounting Bracket Extension Mounting Bracket 13.7”(W) x 20.5”(H) x 2.
PAGE 4
Version 1.0 * May 2011 This publication provides instruction for installing the SpeedCell repeaters. The images for the User Interface in this publication may vary from the repeater’s depending on its S/W Version. Copyright © 2011, GS Teletech, Inc. All Rights Reserved Printed in Republic of Korea Revision History Date Version 05/2011 Version 1.
PAGE 5
Version 1.0 * May 2011 Warnings and Hazards WARNING! ELECTRIC SHOCK Opening the BDA (bi-directional amplifier) could result in electric shock and may cause severe injury. WARNING! EXPOSURE TO RF Working with the repeater while in operation, may expose the technician to RF electromagnetic fields that exceed FCC rules for human exposure. Visit the FCC website at http://www.fcc.gov/oet/rfsafety to learn more about the effects of exposure to RF electromagnetic fields.
PAGE 6
Version 1.0 * May 2011 Mounting Repeater Wood-Framed Wall • It is recommended to first attach a sheet of plywood to the wall. The sheet of plywood should be anchored to the studs in the wall. • Using a pencil, mark the location for each of the mounting bracket's four mounting holes on the plywood. • Place the mounting bracket over the four lag screws heads. • Thread a lag screw at the positions marked in step 2.
PAGE 7
Version 1.0 * May 2011 Hang and Grounding • Hang the PSU unit to the mounting bracket. • Locate the two Mounting Sems Screws (M6 x10mm) underneath the PSU unit. Tighten bolts until secure. Mounting Sems Screw M6 x 10mm Hanging the PSU Unit.
PAGE 8
Version 1.0 * May 2011 Hang and Grounding • Hang the rest of the units in the following order: 2600AMP, DFM 2. • Locate the two Mounting Sems Screws (M6 x10mm) underneath each unit. Tighten bolts until secure. CAUTION Units must be hung in the following order only: 2600 AMP -> DFM 2 Hanging the Rest of Units.
PAGE 9
Version 1.0 * May 2011 Hang and Grounding • Connect ground cables of each unit to the bracket using Ground Sems Screws (M4 x 8mm) as displayed at the picture below. CAUTION Ground Cable Ground cables must be properly grounded to provide both EMI and voltage surge protection for the repeater. Grounding of the PSU, 1900 AMP, DFM 1, 800/900 AMP, 2600 AMP, DFM 2 Units.
PAGE 10
Version 1.0 * May 2011 Hang and Grounding • Locate the ground lug on the underside (or side) of the bracket. • Crimp the ground cable to the ground lug. • Route the free end of the ground cable to an approved (per local code or practice) ground source. CAUTION Ground cable must be properly grounded to provide both EMI and voltage surge protection for the repeater. Grounding the Bracket.
PAGE 11
Version 1.0 * May 2011 Position Antenna • After installing 2600MHz antennas the installer should make line of site. • Customer specifications should be followed for positioning the antennas properly Warning: In order to avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the antenna should not be less than 20cm during normal operation. The gain of the antenna is 12 dBi. .
PAGE 12
Version 1.0 * May 2011 RF Cable Connections: Top of The Repeater • Connect the 2600 Donor Antennas to their corresponding ports. • Plug in four N(M) to N(M) type RF cables as demonstrated in the picture below. A B C D E F CAUTION Do not connect or disconnect cable from ANT port when power is ON.
PAGE 13
Version 1.0 * May 2011 RF Cable Connections: Front Side • Take out two SMA (M) to SMA (M) type RF cables. • Please, pay attention to cable’s corresponding number and its color while connecting. • Connect 2600 AMP and DFM 2 via Band 3.
PAGE 14
Version 1.0 * May 2011 RF Cable Connections: Bottom of The Repeater • Take out three SMA (M) to SMA (M) type RF cables. • While connecting the PSU and the DFM units underneath, use referenced cable and pay attention to the labels. Plug them into their corresponding outlets. • User may choose either of the two SMA ports on the bottom of the PSU to connect to the DFM. • User may choose any two of the four SMA ports on the bottom of the PSU to connect to amplifiers.
PAGE 15
Version 1.0 * May 2011 Power Cord Connections • Plug in the cables to PSU, 2600 AMP and DFM 2 as displayed at the picture below. DFM AMP 10M REF. 10M REF. 10M REF. 10M REF. 1. RS485_P 2. RS485_N 3. GND 4. INSERT 5. RESET 6. NC 7. ID_RESERVE 8. GND 9. ID1 1. RS485_P 2. RS485_N 3. GND 4. INSERT 5. RESET 6. NC 7. ID_RESERVE 8. GND 9. ID1 1. RS485_P 2. RS485_N 3. GND 4. INSERT 5. RESET 6. NC 7. ID_RESERVE 8. GND 9. ID1 10. ID2 11~16. COM_GND 17~20. NC A1. 5.5V 10. ID2 11~14. COM_GND 15~18. NC 19~22.
PAGE 16
Version 1.0 * May 2011 Connecting Power Cable and LED Light Verification • Connect Power Cable • Turn the switch “ON” on the left side of PSU. System On System Off AC Power Port Connection. ON/OFF Switch of SpeedCell Repeater. • Turn the switch “ON” on the front side of PSU as displayed at the picture 12. Verification of LED Lights.
PAGE 17
Version 1.0 * May 2011 LED Indicators • The LED’s on the repeater will light up and should change to green as displayed at the picture below. Tx and Rx LEDs will be blinking. RUN LED : Green light ON. ALARM LED : Green light is normal status, Red light is alarm status. SHUT DOWN LED : Green light is normal status, Red light is shutdown status.

PAGE 18

Version 1.0 * May 2011 Input Power Signal • Please note the number of LED bars for input indicates signal strength level. The tables below indicate the levels. Number of LED bars on the front side of Repeater will show input signal level: Less than ~ -86dBm LED 1bar -85dBm~-79dBm LED 2 bars -78dBm~-72dBm LED 3 bars -71dBm~-65dBm LED 4 bars More than -64dBm LED 5 bars

LED Bars Indication.

PAGE 19

Version 1.0 * May 2011 Output Power Signal • Please note the number of LED bars for output indicates signal strength level. Number of LED bars on the front side of Repeater will show output signal level: Less than ~ +5dBm LED 1bar +6dBm~+10dBm LED 2 bars +11dBm~+15dBm LED 3 bars +16dBm~+20dBm LED 4 bars More than +21dBm LED 5 bars

LED Bars Indication.

PAGE 20

Version 1.0 * May 2011 Web UI • LAN port is used for connection of laptop and repeater. • WAN 1 port is used for connection of repeater and wireless modem for remote access. • WAN 2 port is a redundancy port for remote access. 1 2 3 Ethernet Port.

PAGE 21

Version 1.0 * May 2011 Configuring Laptop to Connect to Repeater • Connect Ethernet crossover cable from the LAN port of the repeater to laptop. 1. Go to Local area connection. 2. Click ‘TCP/IP Properties’. 3. Choose ‘Obtain DNS server address automatically’.

PAGE 22

Version 1.0 * May 2011 Login Screen Enter IP address by 192.168.2.1, you will be redirected to Login. Default User Name is ‘admin’, and default Password is ‘admin’. You may need to change password as described in the User Management section. Engineering Number and Site Name will initially be blank, you can input Engineering Number and Site Name as described in the Communications Configuration section. Repeater’s IP Address: 192.168.2.

PAGE 23

Version 1.0 * May 2011 Menu Select • After you log in, you can see ‘Menu Select’ page. • To setup the Repeater, click ‘Initial Installation’. • To go to menu list, click ‘Menu Page’.

PAGE 24

Version 1.0 * May 2011 Setup Wizard • After you clicking on ‘Initial Installation’ the following screen will be displayed. • After typing the Latitude or Longitude numbers, press ‘Apply’ button. • User may skip this window if it is unnecessary.

PAGE 25

Version 1.0 * May 2011 Setup Wizard ① Auto Configuration matches amplifier and DFM units automatically. ② Manual Configuration matches amplifier and DFM units manually.

PAGE 26

Version 1.0 * May 2011 Setup Wizard • After clicking Auto Configuration, the screen below will be displayed. • It will take approximately one minute to finish the process.

PAGE 27

Version 1.0 * May 2011 Setup Wizard Manual Setup Wizard for 2600MHz Band • User may choose bandwidth in this menu. After selecting bandwidth, click ‘Apply’ button. • Also User may skip this setting if it is not needed.

PAGE 28

Version 1.0 * May 2011 Setup Wizard Manual Setup Wizard for 2600MHz Band (Choosing antenna) • After selecting an antenna type, click ‘Apply’ button. • Also User may skip this setting if it is not needed.

PAGE 29

Version 1.0 * May 2011 List Menu • After clicking on ‘Main Page’, the ‘List Menu’ will be displayed. • User may check the Repeater status by clicking on ‘Status’.

PAGE 30

Version 1.0 * May 2011 Status Menu • User may check status of amplifiers by clicking on any of them.

PAGE 31

Version 1.0 * May 2011 RF Configuration Menu • Click the RF Configuration link. • Click AMP 1, AMP 2 or AMP 3 in order to go to the next window and change RF values.

PAGE 32

Version 1.0 * May 2011 RF Configuration Menu FAQ’s • What is Auto Limit Control (ALC)? ALC is used for custom installations. If the repeater is having difficulties with isolation check, or if you want to “power down” the repeater ALC should be manually set. Attenuation may also be added for reducing power levels. ALC also provides optional U/L and D/L settings. - ALC controls the output power. - If you want to use the ALC function, Gain Balance Control should be turned off.

PAGE 33

Version 1.

PAGE 34

Version 1.0 * May 2011 RF Configuration Menu 2600MHz Band Selection Band Selection Algorithm ITEM BANDWIDTH NOTE Band Select 2 contiguous band is selectable AB , BC, CD, EF, FH, HG are selectable only Band Structure A 2502 B 2518.5 C 2535 Blank D 2551.5 2568 E 2624 F 2640.5 H 2657 G 2673.

PAGE 35

Version 1.0 * May 2011 RF Configuration Menu • Click the RF Configuration link. Click AMP 1, AMP 2 or AMP 3 in order to go to the next window and change RF values.

PAGE 36

Version 1.0 * May 2011 RF Configuration Menu 2600 AMP • User may change various RF values of the repeater on this page. • Changes will not take effect until you click “Apply” button. • This menu is where the installer will choose references for specific implementation. • In case that screen resolution is 1024 x 768, you may need to use scroll bar to view all.

PAGE 37

Version 1.0 * May 2011 RF Configuration Menu 2600 AMP (continue of the page) • User may change various RF values of the repeater on this page. • Changes will not take effect until you click “Apply” button. • This menu is where the installer will choose references for specific implementation. • In case that screen resolution is 1024 x 768, you may need to use scroll bar to view all.

PAGE 38

Version 1.0 * May 2011 Alarm Configuration Menu • Click ‘2600’ link to check alarm configuration of 2600AMP. • In case that Report Alarms is OFF, all alarms will be disabled. In case that Report Alarm is ON, you can enable and disable individual alarms.

PAGE 39

Version 1.0 * May 2011 Communication Configuration Menu • Click on the ‘Communications Configuration’ link. • On this page you can change various values related to IP network. Because Web UI is based on IP network, incorrect configuration may make it impossible to connect to Web UI. In that case, you can troubleshoot as described in the Command Line Interface (CLI) section. • In case that screen resolution is 1024 x 768, you may need to use scroll bar to view all.

PAGE 40

Version 1.0 * May 2011 Communication Configuration Menu • On this page you can change various values related to IP network. • Changes will not take effect until you click “Apply” button. • In case that screen resolution is 1024 x 768, you may need to use scroll bar to view all. In the line “Static” means connection using a fixed IP. “DHCP” means connection using DHCP, where If "DHCP Client" is "ON", then the repeater will run as a DHCP client.

PAGE 41

Version 1.0 * May 2011 User Management Menu • Click on the ‘User Management’ link. • On this page you can create and delete users, change passwords, and assign authorities to individual users. • Read will only all the user to view information on the menu pages, but cannot make any changes. • Read/Write Authority means that the user can view and change various values. • Super User is very similar to an Administrator account... CAUTION DO NOT DELETE ‘admin’.

PAGE 42

Version 1.0 * May 2011 Alarm Logs • Click on the Alarm Logs link. • You can see a history of reported and reset Alarms. When an alarm is reported, the name and time of the alarm is displayed along with it’s current status. Red color means that the alarm is reported, and green color means that the alarm has returned to normal status. • After an Alarm condition lasts for the “Delay Alarm Reporting Minutes” set in RF Configuration page, the Alarm will be reported.

PAGE 43

Version 1.0 * May 2011 Logs • Click on the Logs link. • You can see Logs regarding Web UI operation. Logs will maintain a history of up to 30 operations. • In case that screen resolution is 1024 x 768, you may need to use scroll bar to view all.

PAGE 44

Version 1.0 * May 2011 Logs Continue of Logs page. • In case that screen resolution is 1024 x 768, you may need to use scroll bar to view all.

PAGE 45

Version 1.0 * May 2011 Troubleshooting • Click on the Troubleshooting link. • You can refer to this page for GST's technical support.

PAGE 46

Version 1.0 * May 2011 Software Upgrade • Click on the Remote Software Upgrade link. • In case that software upgrade is needed, you should use this page. • Click Browse button to select the file to upgrade from the laptop. • Choose the file to upgrade provided by GST. After you choose the file, you should click “upload” to send the file from your laptop to the Repeater. • Provided files are three, need to download each of them. - The files are, - ① SC_SNMP.MCU - ② SC_AMP.AMP - ③ SC_DFM.SDR SC_DFM.

PAGE 47

Version 1.0 * May 2011 Software Upgrade • After uploading is finished, verify that the File Name and the File Size is correct, then click ‘Upgrade System’ button. The lights on the repeater will be blinking and change color during upgrade which will take about two minutes for the upgrade to initialize. The lights will go back to normal when upgrade is done.

PAGE 48

Version 1.0 * May 2011 System Reset • Click 'No' to return to the 'List' menu. • Click 'Yes' to reset the repeater via a soft-boot.

PAGE 49

Version 1.0 * May 2011 System Reset • Click 'No' to return to the 'List' menu. • Click 'Yes' to reset the repeater via a soft-boot. This will not change any of the current settings.

PAGE 50

Version 1.0 * May 2011 Factory Default Settings • Choose type of configuration to be restored to factory default settings.

PAGE 51

Version 1.0 * May 2011 Factory Default Settings • This function will allow you to roll back to factory default settings.

PAGE 52

Version 1.0 * May 2011 Configuration Transfer • Configuration Transfer function is for downloading and uploading set values of the repeater.

PAGE 53

Version 1.0 * May 2011 Configuration Transfer: Download • Configuration Transfer Download Display.

PAGE 54

Version 1.0 * May 2011 Configuration Transfer • Downloading process of set values.

PAGE 55

Version 1.0 * May 2011 Configuration Transfer: Upload • Uploading process of set values. • Verify correct file is selected and click ‘Configuration Transfer’.

PAGE 56

Version 1.0 * May 2011 Command Line Interface (CLI) • In case that you cannot reach Web UI, you should use CLI. You should connect the equipment’s CLI port to your laptop’s serial port using RS-232 cable. In case that your laptop does not have a serial port, you may need to use USB to Serial conversion cable. • To open HyperTerminal, click “Start”, then “Accessories”, then “Communications”, then “HyperTerminal”. CAUTION RS-232 cable or USB to Serial conversion cable is not provided with the equipment.

PAGE 57

Version 1.0 * May 2011 CLI • To verify and/or change port number, open “Control Panel”, then “System”, then “Hardware Tab”, then “Device Manager”. Double click “Ports”, then double click “Serial Cable” then click “Port Settings” tab, click “Advanced”, in the COM Port drop down menu, select “COM 1”, click “OK”. • After verification of port number, open HyperTerminal. • Enter CLI. • Click “OK”.

PAGE 58

Version 1.0 * May 2011 CLI • In the “Connect using” drop-down menu, select “COM1”. • Click “OK”.

PAGE 59

Version 1.0 * May 2011 CLI • “Bit per second” drop down menu, select “115200”. • “Flow control” drop down menu, select “None”. • Click “Apply”. • Click “OK”.

PAGE 60

Version 1.

PAGE 61

Version 1.0 * May 2011 CLI • On ‘Settings’ tab. • ‘Emulation’ drop down menu, select ‘VT100’. • Click ‘OK’.

PAGE 62

Version 1.0 * May 2011 CLI • In case that you cannot see login prompt, just press enter key several times. Login is ‘admin’ and Password is ‘admin’.

PAGE 63

Version 1.0 * May 2011 CLI • In order to verify IP network configuration, you should type ‘communication’. • Press enter-key.

PAGE 64

Version 1.0 * May 2011 CLI • In order to see values, you should type “get all”, and then press the enter-key. • Enter the following text: “set LAN_port_IP_address 192.168.2.1”, then press the enter-key. “set LAN_port_DHCP_Server ON”, then press the enter-key. “set WAN_port_IP_address 192.168.1.1”, then press the enter-key. “set WAN_port_DHCP_Client OFF”, then press the enter-key. “commit”, then press the enter-key.

PAGE 65

Version 1.0 * May 2011 GST Technical Support Phone: Toll Free: 1-866-9 GST USA Phone: 913-469-6699 Write: GS Teletech Inc. 6900 College Boulevard, Suite 850, Overland Park, KS 66211, USA Product Information and Technical Assistance: www.gsteletechinc.com support@gsteletechinc.com Specifications and features of this installation guide are subject to change without notice or obligation.

PAGE 66

Warning: Exposure to Radio Frequency Radiation The radiated output power of this device is far below the FCC radio frequency exposure limits. Nevertheless, the device should be used in such a manner that the potential for human contact during normal operation is minimized. In order to avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the antenna should not be less than 20cm during normal operation. The gain of the antenna is 12 dBi.