HOME 3000 User Guide www.americanbst.
Memo This publication provides instructions for installing Cellular Signal Booster Home 3000. Copyright© 2019, American Booster Inc. All Rights Reserved. Revision History Date Version Changes 2019, January Version 1.0 Original Certification This equipment complies with the FCC / IC directives. Technical Support : 913 469 6699 www.americanbst.
Memo INDEX Product Introduction 4 Package Contents 5 Application Example 6 Installation Guide 7 STEP 1. Find the Strongest Signal 8 STEP 2. Install the Outside Antenna 8 STEP 3. Run the Antenna Cable 10 STEP 4. Run the Cable to the Booster 12 STEP 5.
HOME 3000 WARRANTY Opening or tampering with the Signal Booster will void all warranties. American Booster provides a 2-year warranty with all of its equipment. Every product of American Booster is guaranteed to be free of material defects or component malfunctions. This warranty does not cover any Signal Boosters that have been exposed to any misuse, abuse, physical damage or inadequate maintenance.
Package Contents IC Warning Statements RSS-GEN, Sec. 7.1.2 – (transmitters) Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.
Application Application Example Example FCC Warning Statements FCC Part 15.105 statement Class B This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Installation Guide Safety Guidelines WARNING STEP 1. Find the Strongest Signal ELECTRIC SHOCK Opening the Signal Booster could result in electric shock and may cause severe injury. DAMAGE TO EQUIPMENT 1-1. Using an iPhone Dial *3001#12345#*, then press Call. Use only the power supply provided in this package. Operating the Signal Booster with antennas in very close proximity facing each other could lead to a severe damage to the Signal Booster. 1-2.
Specifications STEP 1. Find the Strongest Signal Note The stronger signal you receive from the base station, the better coverage you will have inside your house/office. -70dBm HOME 5000 700 850 1900 2100 If you have -70dBm outside signal, then you will have an excellent signal inside your house or office. -90dBm HOME 5000 700 850 1900 2100 If you have -90dBm outside signal, then you will have a good signal inside your house & office.
Troubleshooting Instructions to fix flashing or solid red. If you have a good voice signal and fast data speeds even though one or two of LEDs are solid red, you may continue to use the Signal Booster as it is. However, if one of the LED’s has flashing or solid red, your voice signal is weak and data speeds are low, Then follow the troubleshooting steps below. 1. Unplug the Signal Booster’s power adapter. STEP 2. Install the Outside Antenna The outside antenna is shaped like a triangle.
LED LED Indicators STEP 2. Install the Outside Antenna 700 Install the outside antenna in a location where you can receive the strongest signal according to the instructions described in STEP 1. Make sure outside antenna is installed with the point of the triangle facing toward the cell tower. 850 1900 700 1 2 850 2100 1900 2100 Flashing Green After the Signal Booster is powered on, flashing green will last for 20 seconds. It means that the Signal Booster is being set up for optimal performance.
STEP 5. Install the Signal Booster Home 3000 has a 360° directional bar antenna. It means you can put the booster on the table or floor or any other place you would like to. Home 3000 can also be attached to the wall, using provided wall-mount brackets. STEP 3. Run the Outside Antenna Cable Connect the outside N-SMA cable with the yagi antenna. Then, connect the window flat cable with the outside cable. 700 850 1900 2100 700 850 1900 2100 700 850 1900 2100 700 850 1900 2100 Outside Antenna to 40 ft.
STEP 4. Run the Cable to the Booster STEP 5. Install the Signal Booster Choose a location for the signal booster, preferably away from excessive heat, direct sunlight, moisture and free from high temperatures. Do not place the signal booster in an air-tight enclosure. Attic installations may expose the booster to high heat. Connect the cable from the booster to the window flat cable. 700 850 1900 2100 To Booster To Booster Cable (20 ft.) Cable (20 ft.
