COLOR TELEVISION VIVANCE II 32 LXW 82-6711 TEXT
CONTENTS------------------------------------------------------------------------------------------------ 2 3 SET-UP AND SAFETY 5 CONNECTION/PREPARATION 5 6 Connecting the antenna and the mains cable Inserting batteries in the remote control 7 OVERVIEW 7 8 9 Connections on the television Controls on the television The remote control 11 SETTINGS 11 11 13 13 Setting television channels automatically Changing stored channels Picture settings Audio settings 15 TELEVISION OPERATION 15 16 16 17
SET-UP AND SAFETY -----------------------------------------------------------Please note the following information when setting up your television set. This television set is designed to receive and display video and audio signals. Any other use is expressly prohibited. The ideal viewing distance is 5 times the screen diagonal. External light falling on the screen impairs picture quality. To assure sufficient ventilation make sure there is enough space around it in the wall unit.
SET-UP AND SAFETY -----------------------------------------------------------Please note when deciding where to put the device that furniture surfaces are covered by various types of lacquer and plastic, most of which contain chemical additives. These may cause corrosion to the feet of the device, thus resulting in stains on the surface of the furniture which can be difficult or impossible to remove. The screen of your LCD television meets the highest quality standards and has been checked for pixel faults.
CONNECTION/PREPARATION ---------------------Connecting the antenna and the mains cable 1 3 2 1 Plug the antenna cable of the rooftop antenna into the »ANT-IN« antenna socket on the television. 2 Plug the mains cable supplied into the »AC IN« mains socket of the television. 3 Plug the mains cable into the wall socket. Note: Only plug the device into the mains socket after you have connected the external devices and the antenna.
CONNECTION/PREPARATION ---------------------Inserting batteries in the remote control 1 Open the battery compartment by removing the lid. 2 Insert the batteries (Mignon type, for example UM-3 or AA, 2x1,5V). Observe the polarity (marked on the base of the battery compartment). 3 Close the battery compartment. Note: If the television no longer reacts properly to remote control commands, the batteries may be flat. Be sure to remove used batteries.
OVERVIEW ---------------------------------------------------------------------------------------------Connections on the television AC IN AV1 Euro/AV socket (FBAS signal, RGB signal). AV2 Euro/AV socket (FBAS signal). PC AUDIO IN Audio signal input for PC. PC-IN VGA socket, video signal input for PC. ANT-IN Antenna socket. SPDIF OUT Audio output sockets (coaxial) for PCM signals. For connecting to a digital multi-channel audio/video amplifier or AV receiver.
OVERVIEW ---------------------------------------------------------------------------------------------Controls on the television 8 Switches the television on and back into standby mode. The only way to disconnect the television from the mains supply is to pull the plug. +P– Switch the television on from standby. Channel selection. Select a function in the menu. TV/AV MENU Opens the »MAIN MENU« menu. Press »TV/AV MENU« and hold down for a second to open the »SOURCE TABLE« menu.
OVERVIEW ---------------------------------------------------------------------------------------------The remote control 8 Switches off the television set (stand-by). 1...0 Switches the television on from standby mode Selects channels directly. ? Displays the number and name of a station; reveals answers in teletext mode. E Switches between picture formats; switches to double character size in teletext mode. PIP Key has no function. AV Opens the pre-selection for AV channels.
OVERVIEW ---------------------------------------------------------------------------------------------SCAN Enlarges the picture. PAT Selects the Split Screen function. S Selects the sub-pages in teletext mode. P Updates a page in teletext mode. DR, DVD Switches to operation of a GRUNDIG digital receiver, GRUNDIG digital receiver with hard disk (PDR), GRUNDIG DVD player or GRUNDIG DVD recorder. Keep the appropriate button (»DR«, »DVD«) pressed down. Then press the appropriate button.
SETTINGS ---------------------------------------------------------------------------------------------------Setting television channels automatically The television set is equipped with an automatic channel search system. You start the search and can then sort the television channels into your order of preference. 99 preset positions are provided, to which you can assign television channels from the antenna or from the cable connection.
SETTINGS ---------------------------------------------------------------------------------------------------Sorting television channels 1 In the »PROGRAM TABLE« menu, select the channel to be moved with with »P+«, »P-«, »4 « or »3 «. PROGRAM TABLE 01 ARD 06 PRO 7 11 ---- 02 ZDF 07 BR 12 ---- 03 BR 08 13 ---- 04 RTL 09 ---- 14 ---- 05 SAT 1 10 ---- 15 ---- OK Skip Name Move Delete Select Exit 2 Highlight the channel with »¥ « (green).
SETTINGS ---------------------------------------------------------------------------------------------------Picture settings 1 Press »i« to open the »MAIN MENU«. – The »MAIN MENU« appears. PICTURE Brightness Contrast Colour Sharpness DNR Color Temperature 2 Select »PICTURE« with »P+« or »P-« and confirm with »OK«. – The »PICTURE« menu appears. AUTO Normal 3 Select »Brightness«, »Contrast«, »Colour«, »Sharpness«, »DNR« or »Color Temperature« with »P+« or »P-«.
SETTINGS ---------------------------------------------------------------------------------------------------Stereo width Widens the audio output for stereo programmes and improves the sound with mono reception. 1 Select »Sound Mode« with »P+« or »P-«. 2 Press »4 « or »3 « to select the setting. Automatic volume The television channels broadcast at different volumes. The automatic volume limiting (AVL) function means the volume is kept the same when you switch between channels.
TELEVISION OPERATION -----------------------------------------Basic functions Switching on and off 1 Press »8«, »1…0« or »P+« or »P-« to switch on the device from standby mode. 2 Press the »8« button to switch the television to standby mode. Selecting channels 1 Use »1…0« to select channels directly. 2 Press »P+« or »P-« to move up and down channels. 3 Open the channel list by pressing »OK«, select the station with »P+« or »P-« and press »OK« to switch off the channel list.
TELEVISION OPERATION -----------------------------------------Picture settings You can select different picture settings. 1 Select the desired picture setting from »User«, »Soft«, »Natural« or »Rich« with »z «. – You can alter the »User« picture setting, see the ”Picture settings” chapter on page 13. Audio settings You can select different audio settings. 1 Select the desired sound setting from »User«, »Music«, »Sport«, »Cinema« or »Speech« with »F «.
TELEVISION OPERATION -----------------------------------------Changing the picture format The television automatically switches to the 16:9 format if this format is detected via the Euro-AV socket. 1 Select the picture format with »E «. The selected picture format, for example »16:9«, appears on the screen. – You can choose between the following picture formats: »4:3« format The picture is shown in 4:3 format. »AUTO« format The picture format is automatically switched to »16:9« for 16:9 programmes.
TELETEXT MODE ---------------------------------------------------------------------------FLOF text and normal text mode 1 Press »TXT« to switch to teletext mode. 2 Use »0…9« to enter the page number directly or »P+« and »P-« to switch up and down pages (to return to page 100, press »i«). Note: At the bottom of the screen, you will see an information line consisting of a red, green and, depending on the station, yellow and blue text field. Your remote control has buttons with the corresponding colours.
TELETEXT MODE ---------------------------------------------------------------------------Calling up a sub-page directly If the selected teletext page contains further pages, the number of the current sub-page as well as the total number of pages is displayed. 1 Call up the sub-pages with »S«. 2 Press »1…0« to enter the sub-menu. 3 Press »S« to quit the function. Reveal answer Certain teletext pages contain ”hidden answers” or information which can be called up. 1 Display information with »?«.
CONVENIENCE FUNCTIONS -----------------------------Convenience functions with the »Features« menu 1 To open the »MAIN MENU« press »i«. 2 Select »FEATURES« with »P+« or »P-« and confirm with »OK«. Note: Further operation is explained in the following sections. Changing the menu language FEATURES Menu language Timer English 1 Select »Menu language« with »P+« or »P-« Parental lock Off 2 Select the language with »4 « or »3 «. 3 Press »i« to finish the setting.
CONVENIENCE FUNCTIONS -----------------------------Activating the parental lock You can block programmes which are unsuitable for children. 1 Select the television channel with »P+«, »P-« or »1...0«. 2 To open the »MAIN MENU« press »i«. FEATURES Menu language Timer English 3 Select »FEATURES« with »P+« or »P-« and confirm with »OK«. Parental lock On 4 Select »Parental lock« with »P+« or »P-« and confirm with »OK«. 5 Activate the parental lock with »4 « or »3 « (On).
USING EXTERNAL DEVICES ---------------------------------DVD player, DVD recorder, video recorder or set-top box Note: Which television socket(s) you connect your external devices to depends on the sockets the external device is equipped with and the signals which are available. Note that with many external devices the resolution of the video signal must be adapted to the input sockets on the television (check the external device’s instruction manual).
USING EXTERNAL DEVICES ---------------------------------With an analogue video signal (progressive) Video signal: YUV; resolution: standard 576p; HDTV 720p, 1080i. Audio signal: stereo, analogue. Channel position »YPBPR«. 1 Connect the »COMPONENT INPUT VIDEO IN Y Pb Pr« sockets on the television and the corresponding sockets on the external device using cinch cables (video signal).
USING EXTERNAL DEVICES ---------------------------------With an analog TV signal Video signal: FBAS. Audio signal: stereo, analogue. Channel position »AV3«. 1 Connect the »AV3 VIDEO IN« cinch socket on the television and the corresponding socket on the external device using cinch cables (video signal). 2 Connect the »AV3 AUDIO IN L R« sockets on the television to the corresponding sockets on the external device using cinch cables (audio signal).
USING EXTERNAL DEVICES ---------------------------------Decoder or satellite receiver In order for the television to receive encoded programs from a privately operated station, a decoder is needed. Connecting a decoder or satellite receiver Decoder 1 Connect the »AV1« socket on the television set and the appropriate socket on the decoder using a EURO-AV cable. Using a decoder or satellite receiver 1 Switch on the television and the decoder or the satellite receiver.
USING EXTERNAL DEVICES ---------------------------------Camcorder Connecting the camcorder 1 Connect the yellow socket »AV3 VIDEO IN« on the television and the corresponding socket on the camcorder (VHS, Video 8) with a cinch cable (picture signal); or connect the »S-VHS« socket (picture signal) on the television and the corresponding socket on the camcorder (S-VHS, Hi 8) with a S-Video cable.
PC MONITOR MODE ---------------------------------------------------------Connecting a PC 1 Connect the socket »PC-IN« on the television to the corresponding socket on the PC using a VGA cable. 2 Connect the socket »PC AUDIO IN« on the television to the corresponding socket on the PC using a cinch cable (audio signal). Note: Adjust your PC to the monitor (for example, picture resolution 1280 x 768, picture frequency 60 Hz).
SPECIAL SETTINGS -----------------------------------------------------------------Setting television channels This setting is only necessary if a new channel comes on air and you do not want to change the order of your channels. The television channel can be set directly or using the search. SETUP System Channel Fine tuning Search Program no Store Autoprogram BG C 03 0 Setting channels using the search as P01 1 Press »i« to open the »MAIN MENU«. – The »MAIN MENU« appears.
SPECIAL SETTINGS -----------------------------------------------------------------Fine tuning television channels The television automatically tunes itself to the best possible reception. You may need to carry out manual fine tuning in areas where there is poor reception. SETUP System Channel Fine tuning Search Program no Store Autoprogram BG C 03 0 1 Press »i« to open the »MAIN MENU«. – The »MAIN MENU« appears. as 2 Select »SETUP« with »P+« or »P-« and confirm with »OK«. – The »SETUP« menu appears.
SPECIAL SETTINGS -----------------------------------------------------------------Re-tuning all television channels You can re-tune all the television stations, for example if you move to another town. SETUP System Channel Fine tuning 1 Select the channel with »P+«, »P-« or »1…0« , to select the preset number from which the new television channels will be added to the channel list, e.g. 1. BG C 03 0 as Search Program no Store Autoprogram P01 2 Press »i« to open the »MAIN MENU«.
INFORMATION -----------------------------------------------------------------------------Technical data Operating voltage: 230V, 50 Hz Power consumption: in operation 145 W in standby approx 2 W Sound output: 2 x 20 watts music (2 x 10 sine wave) Reception range: C01 … C80, special channels S01 … S41 Preset channels: 99 and 7 AV Screen size: 81 cm/32“ Max.
INFORMATION -----------------------------------------------------------------------------Troubleshooting If the remedies given below do not work, please consult an authorised GRUNDIG dealer. Please bear in mind that malfunctions can also be caused by external devices such as video recorders or satellite receivers.
INFORMATION -----------------------------------------------------------------------------Additional Information for units sold in the UK. Units sold in the UK are suitable for operation from a 240V ac, 50Hz mains supply. The range of multi-system receivers is built to work in most European countries. However, the mains plug and socket system for the UK differs from many European countries. This appliance has been supplied with a fitted, non-removable, approved converter plug for use in the UK.
Atrium, Strawinskylaan 3105 • NL-1077 ZX Amsterdam • http://www.grundig.
