Installation and Operating Instructions
Table Of Contents
- English (GB)
- 1. General information
- 2. Installing the product
- 3. Starting up the product
- 4. Product introduction
- 5. Control functions
- 6. Setting the product
- 6.1 Setting the sensor type
- 6.2 Setting the start level
- 6.3 Setting the stop level
- 6.4 Setting the high level
- 6.5 Stop delay
- 6.6 Power-on delay
- 6.7 Dry-running protection
- 6.8 Using the same level switch for the start and stop level
- 6.9 "Multipump settings"
- 6.10 "Antiseizing"
- 6.11 Signal detection time
- 6.12 Setting the maximum number of restarts with Grundfos GO Remote
- 6.13 Setting the service interval with Grundfos GO Remote
- 6.14 Operating the product
- 6.15 Motor protection
- 6.16 Alarm reset
- 6.17 Setting the buzzer with Grundfos GO Remote
- 6.18 Setting units for Grundfos GO Remote
- 6.19 Setting units for the operating panel with Grundfos GO Remote
- 6.20 GENIbus
- 6.21 Security
- 6.22 Starting the startup wizard with the operating panel
- 7. Servicing the product
- 8. Fault finding the product
- 8.1 Overview of alarm and warning codes
- 8.2 Code 2 (Power phase missing)
- 8.3 Code 4 (Too many motor restarts)
- 8.4 Code 9 (Power phase sequence wrong)
- 8.5 Code 12 (Service needed)
- 8.6 Code 22 (Moisture in motor of pump)
- 8.7 Code 25 (Wrong configuration)
- 8.8 Code 26 (Contactor shorted)
- 8.9 Code 48 (Motor is overloaded)
- 8.10 Code 51 (Blocked)
- 8.11 Code 57 (Missing water in the application)
- 8.12 Code 69 (Winding temperature too high)
- 8.13 Code 72 (Internal fault)
- 8.14 Code 76 (Internal fault)
- 8.15 Code 84 (Memory storage media faulty)
- 8.16 Code 85 (Internal fault)
- 8.17 Code 117 (Door opened)
- 8.18 Code 159 (Communication error CIMxxx)
- 8.19 Code 163 (Drive unit configuration fault)
- 8.20 Code 165 (Signal fault)
- 8.21 Code 191 (High water level)
- 8.22 Code 205 (Level switch inconsistency)
- 8.23 Code 220 (Contactor wear out)
- 8.24 Code 229 (Water on floor)
- 9. Technical data
- 10. Disposing of the product
6.22 Starting the startup wizard with the
operating panel
• Press and hold the OK button for 8 seconds until
S-1 or S-2 starts flashing.
Related information
3.3 Startup wizard on the operating panel
7. Servicing the product
DANGER
Electric shock
Death or serious personal injury
‐ Switch off the incoming power supply
before you start any work on the
product or connected pumps.
‐ Make sure that the power supply
cannot be switched on accidentally.
7.1 Updating the product software
New features and functions can be made available
during the product's life cycle.
1. Contact Grundfos to get your product software
updated.
7.2 Replacing the control unit
DANGER
Electric shock
Death or serious personal injury
‐ Switch off the power supply before
making any electrical connections.
‐ Make sure that the power supply
cannot be switched on accidentally.
Remember to save the controllers settings in
Grundfos GO Remote under Settings. The settings
can then be transferred to the new control unit when
installed.
1. Switch off the power supply to the product and
other components with external supply.
2. Write down the terminal connection of each wire
to ensure correct re-connection.
3. Disconnect all wires.
4. Remove the control unit from the panel or
cabinet.
5. Fit the new unit.
6. Connect all wires.
7. Configure the new control unit using Grundfos
GO Remote.
7.3 Replacing the CIM module
DANGER
Electric shock
Death or serious personal injury
‐ Switch off the power supply before
making any electrical connections.
‐ Make sure that the power supply
cannot be switched on accidentally.
1. Switch off the power supply to the product and
other components with external supply.
2. Write down the terminal connection of each wire
to ensure correct re-connection.
3. Disconnect all wires connected to the CIM
module.
4. Remove the screws that holds the module.
5. Remove the module from the control unit.
6. Fit the new module.
7. Connect all wires.
7.4 Replacing the battery
CAUTION
Fire and chemical leakage
Minor or moderate personal injury
‐ Risk of explosion if the battery is
replaced by an incorrect type.
To replace the battery, do the following:
1. Remove the front cover
2. Gently grab around the battery without touching it
too much.
3. Push the battery to the side to release it.
4. Pull the battery up.
5. Insert a new battery of the correct type.
Related information
9. Technical data
8. Fault finding the product
DANGER
Electric shock
Death or serious personal injury
‐ Switch off the power supply before you
start any work on the product.
‐ Make sure that the power supply
cannot be switched on accidentally.
Fault finding and fault correction must be carried out
by qualified persons.
23
English (GB)