Submittal Sheet

ManualsBrandsGrundfos ManualsCirculator PumpsTPE50-160/2 E-Circulator Pump, 1-1/2 HP, Bronze, 208-230V, GF 50 Flange Mount

Company name:

Created by:

Phone:

Fax:

Date:

Printed from Grundfos CAPS [2011.05.069]

Position Count Description Unit price

-1 On

request

TPE 50-160/2 B U-G-Z-BUBE

Product photo could vary from the actual product

Product No.: 91136596

Single-stage, centrifugal, in-line, single-head

pump.

The in-line design with opposite suction and dis-

charge ports enables mounting in pipework or on

a concrete foundation.

The shaft seal is a corrosion resistant

maintenance-free mechanical seal.

The pump is fitted with a three-phase

MLE motor with frequency converter and

PI-controller integrated in the motor terminal

box. No additional motor protection is required as

both motor and electronics are protected by

integrated overload and temperature protection.

External sensor can be connected if controlled

pump operation based on for example flow,

differential pressure or temperature is required.

A control panel enables setting of required

setpoint as well as setting of pump to MIN or MAX

operation or to STOP. The control panel has

indicator lights for "Operation" and "Fault".

Communication with the pump is possible by means

of Grundfos R100 Remote Control enabling further

settings as well as reading out of a number of

parameters such as "Actual value", "Speed",

"Power input" and total "Power consumption".

The terminal box holds terminals for the

connection of:

- Pump start/stop (potential-free contact),

- external remote setpoint setting via analog

signal, 0 - 5 V, 0 - 10 V, 0(4) - 20 mA,

- 5 V voltage supply for setpoint potentiometer,

Imax = 5 mA,

1/6

Summary of content (6 pages)

PAGE 1
Company name: Created by: Phone: Fax: Date: Position Count -1 - Description Unit price TPE 50-160/2 B U-G-Z-BUBE On request Product photo could vary from the actual product Product No.: 91136596 Single-stage, centrifugal, in-line, single-head pump. The in-line design with opposite suction and discharge ports enables mounting in pipework or on a concrete foundation. The shaft seal is a corrosion resistant maintenance-free mechanical seal.
PAGE 2
Company name: Created by: Phone: Fax: Date: Position Count Description - Unit price sensor, 0 - 5 V, 0 - 10 V, 0(4) - 20 mA, 24 V voltage supply for sensor, Imax = 40 mA, input for forced control to MIN or MAX (potential-free contact), potential-free fault signal relay with changeover contact, RS485 GENIbus. Liquid: Liquid temperature range: Liquid temp: 5 .. 284 °F 68 °F Technical: Actual calculated flow: Resulting head of the pump: Shaft seal: Maximum operating pressure: 92.9 US gpm 36.
PAGE 3
Company name: Created by: Phone: Fax: Date: Product Number: EAN number: H 100 % (ft) Value TPE 50-160/2 B U-G-Z-BUBE U-G-Z BUBE 91136596 5700838068764 40 90 % 80 % 30 Installation: Maximum ambient temperature: Maximum operating pressure Flange standard: Connect code: Pipe connection: Pressure stage: Flange size for motor: 104 °F 145 psi US Bronze G 2" 125 psi 56C Liquid: Liquid temperature range Liquid temp: 5 ..
PAGE 4
Company name: Created by: Phone: Fax: Date: - 91136596 TPE 50-160/2 B 60 Hz cos phi eta 1 TPE 50-160/2 B + 90CC I (A) 10 1.5 HP 3* 220 V, 60 Hz cos phi 0.8 eta 0.6 I 8 6 0.4 4 0.2 2 0 0 n (rpm) 0.2 0.4 0.6 0.8 1 1.2 1.4 1.6 1.8 2 0 2.2 P2(HP) P1 n (kW) 3000 3 2500 2000 P1 2 1500 1000 1 500 n = 100 % 0 Printed from Grundfos CAPS [2011.05.
PAGE 5
Company name: Created by: Phone: Fax: Date: - 91136596 TPE 50-160/2 B 60 Hz 4 3/4" M12 6 9/16" 10 3/8" 5 15/16" NPT 1/4 3 1/4" 2 1/2" 3 1/8" 5/8" 20 5/8" 3 15/16" 3 15/16" 2 1/8" 3 7/16" 7" 14" 4 1/16" 5 1/4" Note! All units are in [mm] unless others are stated. Disclaimer: This simplified dimensional drawing does not show all details. Printed from Grundfos CAPS [2011.05.
PAGE 6
Company name: Created by: Phone: Fax: Date: - 91136596 TPE 50-160/2 B 60 Hz L1 L2 L3 0-10 V 0/4-20 mA 4-20 mA 1 9 8 7 B Y A 1: 9: 8: 7: B: Y: A: Digital input GND (frame) +24 V Sensor input RS-485B Screen RS-485A Group 1 1/0 Group 3 Group 2 NC C NO STOP 6: GND (frame) 5: +10 V 4: Setpoint input 3: GND (frame) 2: Start/stop RUN 0/4-20 mA 0-10 V 10K 6 5 4 3 2 All units are [mm] unless otherwise presented. Printed from Grundfos CAPS [2011.05.