• Copyright © 2007 Group Sense Mobile-Tech Limited. All rights reserved. • Product specifications and features are for reference only and are subject to change without prior notice. Copyright Copyright Declaration • This User Guide is published by Group Sense MobileTech Limited., without any warranty.
Typographical conventions 2 Typographical conventions It is important to understand the terms and typographical conventions used in this User Guide.
PLEASE READ THIS CAREFULLY BEFORE USING HATCHBACK IN YOUR VEHICLE! • It is your responsibility to place the Hatchback securely on your vehicle. • Mount the Hatchback in a position that is secure, does not obstruct the driver’s view and will not obstruct you from leaving your vehicle in the event of an accident. • Do not operate the Hatchback while driving. • You’d better familiarize yourself with your device and its operation before using it. • Keep the Hatchback cool. Out of direct sunlight.
Important safety information 4 Internal battery safety information • The internal battery is a non-replaceable internal lithiumion polymer battery. It may explode if mishandled. To reduce the risk of fire or burns, do not disassemble, crush or puncture the battery. • Recycle or dispose of the battery safely and properly according to local laws and regulations. Do not dispose of the battery in fire or water.
Welcome 8 Getting to know your Hatchback . . . . . . . . . . . . . . . . . . . . . . 9 Front components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Back components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Up components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Bottom component . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Side components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Internal battery . . . . . .
Table of Contents Setup destination in Map view mode . . . . . . . . . . . . . . . 41 Start navigation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 Turbodog main menu 44 Go home . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 Set up my home . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 Edit recent destinations . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 Map view . . . . . . . . . . . . . . . . . . . . . . . . . . .
Camera 92 Activating camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92 Customizing camera preferences . . . . . . . . . . . . . . . . . . 93 Taking a photo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95 Managing photos . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95 Photo Viewer 96 Accessing Photo Viewer . . . . . . . . . . . . . . . . . . . . . . . . . . . 96 Photo management . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Welcome 8 Welcome Thank you for using Hatchback navigation system, a global navigation system for vehicles. It utilizes the GPS (Global Position System) technology. This software will bring you with a pleasant driving experience more convenient, more comfortable. This User Guide will guide you throughout the operation of your Hatchback step by step. Please read this User Guide carefully before using your Hatchback for the first time, and keep this Guide for future reference.
We strongly recommend that you familiarize yourself with the Hatchback.
Welcome Back components Component Description 7 GPS receiver Receive signals from GPS satellites 8 Camera Camera lens 9 Battery lock Set it on for normal use; switch to off to cut internal battery connection 10 Reset hole 10 Use stylus to reset the Hatchback
Welcome Up components Component Description Camera button Turn camera on; press to take a photo Bottom component 12 Component Description Charging socket Connection socket for AC power 11
Welcome Side components Component 12 Description 13 Earphone Connection socket for earphone 14 External card slot Slot for memory card 15 Stylus slot Slot for stylus
The Hatchback has an internal battery, the battery indicator lights on the front of the Hatchback indicates the level of internal battery charge: • Green - Battery full • Red - Battery low • Orange- Battery charging Welcome Internal battery Charging battery • To charge the Hatchback using an electrical wall outlet, plug the AC power cable into the charging socket on the bottom of the Hatchback and the AC power pack into the wall outlet.
Welcome Inserting external card • Insert the card with the metal contact facing upwards into the card slot as illustrated below. Removing external card • Press the inserted card to release and then remove card.
This chapter will guide you to the basic operation of input methods. Welcome Input methods Using input methods To activate an application that information needed (e.g., Photo Viewer) 1. Select a photo in the thumbnail view of Photo Viewer to the full view screen. 2. Tap to view the information of the selected photo. 3. In the Photo Information screen, tap to show the input panel; tap it again to hide the input panel. 4. Enter characters.
Welcome Input methods options There are several input methods for you to enter letters when you edit photo information. Selecting input methods 1. In the Photo Information edit screen, tap on the upper right corner of to select Option. 2. Select the input method you need from the list. (Attention: The input method can not be left blank, you must select one at least.) 3. Tap to save. 4. The selected input method will be displayed in the popup menu when tap . Options selection 1.
Quick reference This chapter gives you a brief introduction how to navigate using TURBODOG while you drive. Before we explore all detailed functionalities provided by this application, you have to make sure that: • Your TURBODOG is firmly mounted on your car. • TURBODOG searches for positioning information from three satellites and your position is oriented when the application starts.
TURBODOG navigation system 18 Getting started 1. Turn on TURBODOG. 2. To tap on Maps icon to start TURBODOG navigator. 3. To enter Greeting page and main menu page.
11 1 4 7 1. 2 3 5 6 8 9 10 : to enter Destination Search menu to select a destination. The application starts navigation once a destination is specified (for detail, please refer to Chap.3) 2. : to navigate you home 3. : to add new POIs or to edit the existing POIs, e.g. TURBODOG navigation system Icon description on main menu modify/delete address, telephone number, etc (refer to Chap.4.
TURBODOG navigation system 4. : to edit a list of destinations currently defined, e.g. delete or search for a destination specified previously (refer to Chap.4.2 for detail) 5. : to view property information of various geographic location on the map and carry out operations on these locations, e.g. zoomin/out, shift map, day/night display mode switch, 2D/3D view mode switch. There are three different way of viewing the map: (1) To view the property of each geographic location on the map shown on screen.
Icon description on navigation TURBODOG navigation system 11. The indictor of TMC reception: Grey indicates RDS-TMC disconnected; Red indicates there is no TMC message; Red-green flash indicates there is a new TMC message. 1. Orientation indicator: to show current position and driving direction of the vehicle (floating point) 2. Proposed driving route: to show a proposed driving route 3. Turn guide: to show the diagram of next turn 4.
TURBODOG navigation system 22 5. Distance to the next turn: to display the distance between your current position to the next turn 6. Driving speed: to display current driving speed 7. Journey info zone: to display total distance to the destination 8. Satellite signal status bar: to display the status of satellite and the number of satellites from where satellite signal is recevied 9. Arrival time: to display the estimated time of arrival destination 10.
In this chapter, you will learn how to setup a destination, calculate a proposed route and start navigation after TURBODOG is activated. From Start Menu to launch TURBODOG and enter Main Menu, click on “Navigate to” to enter “Managing navigation” page. tick on “add a new destination” (Squred in red as shown in picture 3.2) to enter “Destination Search“ page shown in picture 3.3.
Start navigation - where do you want to go? 24 Setup a destination TURBODOG provides six searching methods to setup a destination by taking different types of destinations into account. Setup destination by address For example: NO. 1, 34 th St, New York 1. In “Search from“, select ” ” to enter “Address Search” page shown in picture 3.5. 2. Click on “city” in “Address Search“ page to enter “country and city selection“ page as shown in picture 3.6 to select a country or city.
4. in picture 3.7, Turbodog shows a list of available countries for selection. In our case, we select “New York“; 5. after selected the country, click on “OK“ to return to “city selection“ page shown in picture 3.8 Start navigation - where do you want to go? 3. In picture 3.6, the current country sleected is Osterreich. To change a different country, e.g. from “Alaska“ to “New York“, you can click on “New York“ squred in red as shown in picture 3.6 to enter another page as shown in picture 3.7. 6.
Start navigation - where do you want to go? 8. in picture 3.9, click on “POSTCODE“ (squred in red) to enter “postcode search“ page shown in picture 3.10. 9. specify the postcode you want to search for, Turbodog automatically lists all postcodes matching your criteria. Locate the one you are searching for and click on it. 10. and then click on “OK to return to “Address Search“ page. The postcode selected is shown in postcode field next to city name.
13. Highlight and click on the name of the road and lick on “OK“ to return to “ Address Search“ page. Start navigation - where do you want to go? 12. Enter the name of (or part of) the road, Turbodog automatically lists all roads matching the searching criteria. 14. After specifying the name of the road, click on street number field, Turbodog enters “street number search“ page.
Start navigation - where do you want to go? 15. Enter the streed number, Turbodog automatically shows the location of this address and enter “Address Search“ page. 8. Click on “OK“, Turbodog returns to “managing navigation“ page. 9. Once a destination is setup successfully, TURBODOG automatically returns to “Managing Navigation“ page and displays the address in destination list.
Setup destination by intersection 1. in “destination search“ page, click on “ “ to enter 3.
Start navigation - where do you want to go? 30 2. Click on text input box of Road to enter “road search“ page. 3. enter the name of (or part of the name of) the road in text box on the top, Turbodog automatically lists all names of the roads matching your searching criteria. 4. Click on “intersection“ text box to enter intersection search page. Turbodog automatically lists all roads which intersects with the road your specified.
6. When destination is setup successfully, TURBODOG automatically returns to “managing navigation“ page and displays the destination in the destination list. 7. Click on Go to start navigation. Start navigation - where do you want to go? 5. Select the road in the list and then press “OK“ to return to “Address Search“ page. The road you selected is displayed in “intersection“ field.
Start navigation - where do you want to go? Setup destination by POI For example: Ansonia Station 1 In “destination search“ page, click on “ “ to enter “POI category“ page as shown in picture 3.26. 2. Click on “All POI“ to select the type of POIs. Turbodog automatically enters “POI search‘ page. 3. In “POI search“ page, click on “Name“ text box to enter “POI input“ page.
5. Select the POI of your interest 6. Then click on “OK“, Turbodog returns to “POI search“ page. 7. Click on “OK“ to end POI search. Start navigation - where do you want to go? 4. Enter the name of (or part of the name of) the POI in “Name“ field on the top, Turbodog automatically lists all POIs matching your criteria.
Start navigation - where do you want to go? 34 8. When successful Turbodog automatically returns to “managing navigation“ page. The destination you selected is listed in destination list. 9. Click on Go to start navigation Setup destination by road of POI 1. In “Destination Search“ page, select “ “ to enter “POI category“ page as shown in picture 3.33.
3. Click on “Street“ to enter “Road Search“ page. Start navigation - where do you want to go? 2. Click on “All POI“ to select the category of POI. Turbodog enters “POI search“ page. 4. Enter the name of the road, Turbodog lists all roads matching your criteria. 5. Select the one you wish to search and lick on “OK“; the system returns to “POI search“ page and the road you selected is displayed in Street field. All POIs along this road are displayed in POI 35 list.
Start navigation - where do you want to go? 36 6. When successful, Turbodog automatically returns to “Managing Navigation“ page and the road you selected is displayed in destination list as the destination. 7. Click on Go to start navigation.
For example: Ansona Station 1. In “Destination Search“ page, select “ “ to enter “Favorites Search“ page as shown in picture 3.39. 2. Select the one you want to set as destination in the list. 3. Then click on “OK“ to end destination setup. Start navigation - where do you want to go? Setup destination by Favorites 4. When successful. Turbodog automatically returns to “Managing navigation“ page and display the destination in the destination list. 5. Click on Go to start navigation.
Start navigation - where do you want to go? 38 Search by nearest POI (Within a radius of 2 km of the map center or GPS position fix) For example: the nearest petrol station 1. In “Destination Search“ page, select “ “ to enter “POI search“ page as shown in picture 3.42. 2. Select the one you want to set as destination in the page. 3. Select “ “ to enter “Nearest POI search“ page as shown in picture 3.43.
6. When successful. Turbodog automatically returns to “Managing navigation“ page and display the destination selected in destination list. 7. Click on Go to start navigation. Start navigation - where do you want to go? 4. Select your destination in the list 5. Then click on OK to confirm destination selection.
Start navigation - where do you want to go? 40 Setup destination by recent destinations 1. In “Destination Search“ page, select “ “ to enter “Recent Destinations search“ page as shown in picture 3.45. 2. Select your desired destination in the list. 3. Then click on OK to end the destination setup. 4. When successful. Turbodog automatically returns to “Managing navigation“ page and list the destination selected in the destination list. 5. Click on Go to start navigation.
1. In “Destination Search“ page, select “ “ to enter “Map view“ page as shown in picture 3.48. 2. Click on screen to shift the map to the location where you want to setup as destination. 3. Set up destination directly on the map by clicking on the location of your desired destination and then press “OK“. 4. When successful. Turbodog automatically returns to “Managing navigation“ page and list the destination selected in the destination list. 5. Click on Go to start navigation.
Start navigation - where do you want to go? 42 Start navigation Turbodog enables you setup 10 midway-point at the same time. The system calculates a proposed route according to the sequence of midway-point you specified and leads to the final destination. When you finish the operations of setting up a destination as described in Chap. 3.1, you can click on “Go“ in “Managing navigation“ page to enter “Map view“ page.
2. After GPS orientation, Turbodog automatically starts route calculation and navigates. * You can press Cancel at any time before route calculation stops. 3. Start navigation. Start navigation - where do you want to go? 1. After setting up destination and click on “Go“, Turbodog automatically enters “Map view“ page and waits for GPS signal as shown in picture 3.52.
Turbodog main menu Turbodog main menu After launching Turbodog, it enters “Main Menu“. It provides six major functions. This chapter describes those functions in details. • In Chap. 3, we have already described how to setup destination. • TMC in Chap. 7, details on functions of TMC will be described. • in Chap. 8, details on how to configure system settings will be described.
In Turbodog’s main menu, click on Turbodog will start receiving GPS signals and enter navigation mode starting navigation. * Before using “Go home“ function, please specify the position of My Home. Turbodog main menu Go home Set up my home In Turbodog’ main menu, click on erence” page.
Turbodog main menu ture 4.5 to enter “Set home“ page, Turbodog provides six searching methods to setup home address. Edit recent destinations Turbodog allows you to edit up to 100 recently destinations through the function of Edit Recent Destination. This function lets you to view and delete any of recently destinations.
1. Click on to enter “Recent Destinations“ page. Turbodog main menu (1) View the position of recent destinations: 2. Select one of the destination from the list. 3. Click on , the destination you have selected is displayed on map as shown in picture 4.8. 4. Click on or to view more inormation of all recent destinations.
Turbodog main menu (2) Delete a recent destination In “Recent Destinations“ page, select the one you want to delete and press button, a dialog box pops up as shown below to let you confirm if you are sure to delete it.
The Map view provides following function: Turbodog main menu Map view If GPS signal is available, it will show your current position. If GPS signal is not available, it will show last position. (1) Shift map: Click on screen to shift map on the screen.
Turbodog main menu Click on any of objectson the map, the name of this object is displayed (See picture 4.12). (4) Search for facilities nearby: Click on “ “ key, it enters “Nearest POI” page. Turbodog will automatically list all POIs within a radius of 50 km of the map center. 1. Select the one you want to set as destination in the page. 2. Select “ 50 “ to enter “Nearest POI search“ page as shown in picture 4.15.
Turbodog main menu 3. Click on key, Turbodog will let you to specify more options.
Turbodog main menu (5) Day/Night mode: Click on “ “ or “ “ key, you can switch display mode between Day mode a nd Night mode. (6) 2D, 3D mode: Click on “ “ or “ “ key, you can switch display mode between 2D and 3D mode.
Click on “ “ key, Trubodog will zoom to current GPS posi- tion. (8) POI search: Click on “ “ key to search for a POI. Turbodog main menu (7) Display current position: (9) Address search: Click on “ “ key to search for an address according to the information you specified.
Turbodog main menu (10) Show trace record: Click on “ “ key to show trace records. Edit favorites Turbodog allows you to bookmark your favorites. These frequently used favorites can be configured as start point or destination of a journey.
click on key to enter “Favorite list“ page as shown in picture 4.25 2. Click on key in this page to enter the page as shown in picture 4.26. There are six way of adding a new favorite. Please refer to Chap. 4.1 and Chap. 4.2 for details. Turbodog main menu 1.
Turbodog main menu 1. In Favorite list page, select the one you wish to delete. 2. Click on key, a dialog box pops up to let you confirm if you are sure to delete it (See picture 4.28). 3. If you select “Yes“, the favorite is deleted. If not, the operation is cancelled and returns to “Favorite list“ page. (3) Edit My Favorite: 1. In “Favorite list“ page, select the one you wish to edit. 2. Click on key to enter “Favorite edit“ page as shown in picture 4.30.
Turbodog main menu 3. Click on the field you wish to edit to activate virtual key board as shown in 4.31.
Manage navigation Manage navigation Turbodog allows you to select configurable tools which enables you to start free navigation (without specifying any destination) to 10 destinations, specify 4 driving methods and set 2 routing parameters. Also it provides you with 2 features of navigation and route view. This lets you use the system any where any time. Below we describe the detailed operations: In main menu, click on icon to enter “Managing Naviga- tion“ page as shown in picture 5.2.
In “Managing Navigation“ page, click on button or button to switch between 2 modes. Navigation mode Manage navigation Navigation and route plan : Turbodog allows you to specify up to 10 destinations. After specifying a destination, click on button, Turbodog will wait for GPS to finish positioning. Once position is fixed, it will calculate a route and start navigation. When clicking on Go without specifying destination, you can also start free navigation.
Manage navigation Route plan mode : 1. Turbodog allows you specify 9 destinations at most and 1 start point. After setting up start point and destinations, click on button, Turbodog will enter “Routing“ page as shown in picture 5.7 to start routing. * Note: In route plan mode, when you move to any candidate destination, this destination will become start point of route. 2. After routing, it enters to “View Route“ page as shown in picture 5.9 to allow you to view entire route.
Manage navigation (1) Click on map to enter map shift mode. This enables you to view proposed route. (2) Click on button to enter entire route view.
Manage navigation (3) Click on button to start simulation as shown in picture 5.14. Specify route parameters Turbodog’s tool provides 4 driving methods and 2 types of routing parameters to satisfy different navigation needs.
key to Manage navigation In “Managing Navigation” page. click on enter “Route Option“ page as shown in picture 5.15.
Manage navigation Manage destination Turbodog allows you to specify up to 10 destinations and 1 start point. (1) Add new destination/start point Navigation mode: Click on to enter “Destination Search“ page to specify destination. Route plan mode: Click on to enter “Destination Search“ page to specify start point.
Manage navigation (2) Delete destination Click onthe one you wish to delete, and press key. A confirmation box pops up.
Navigation Navigation Turbodog provides six functions in navigation or Simulation mode. Click on screen to enter “Navi Option“ page as shown in picture 6.2. If there is no action detected for 5 seconds, the system returns to navigation page. In Navi Option page, it provides following functions: (1) Day/Night mode switch Click on or Day and Night mode.
Navigation (2) 2D/3D mode switch Click on or key, it switches display mode between 2D and 3D mode. (3) Detour In Navi option page, click on option“ page as shown in picture 6.7.
Navigation When traffic jam, you can estimate the distance to the blocking point and select an appropriate option, Turbodog will calculate a detouring route. (4) View entrire route In Vavi option page, click on key to display entire route in map view mode as shown in picture 6.8.
on icon to display GPS status page as shown in picture 6.9. Navigation In navi option page, click (6) Teminate nabigation In Navi option page, click on icon to teminate navigation and return to main menu page. Auto-routing With consideration of driving safety, Turbodog provides autorouting function. This feature executes under two circumstances: Auto starting navigation: after setting up destination, click on icon in “Managing navigation“ page, Turbodog will automatically start navigation.
Navigation 70 1. Proceed to the next step if GPS receiver has received signals from all of three GPS satellites and finished position orientation. Otherwise, keep waiting for GPS signals; 2. Set current GPS position as start point and the destination you have set as the destination of the journey, use “Uptimal route“ as default parameter of route calculation and start navigation after routing.
This feature enables you to view entire route after route calculation in the course of navigation. Route description: each description contains 4 elements including street name you are on, driving distance, turn method and street name you are entering. For example: drive along “Ang Mo Kio Avenue“ for 257.5 meters and make a right turn to “Marymount Road“. Navigation Entire route view There are two methods to view entire route: • After routing, click on button as shown in picture 6.
RDS-TMC traffice and travel information system 72 RDS-TMC traffice and travel information system Turbodog is equipped with the function of RDS-TMC. This function enables to receive real-time traffic condition nearby and to show on the map. When there is an emergency on the route calculated, the system will prompts to recalculate a detour to avoid the traffice jam. TMC turn on/off After Turbodog started, the system will automatically connect to RDS-TMC device to receive TMC message.
3. Click on Back, it returns to main menu or Navigation screen. The TMC status is in grey which indicates that TMC receiving is disabled. RDS-TMC traffice and travel information system 1. In main menu or Navigation screen, click on “TMC“ to enter the window shown in picture 7.3. 2. Click on “TMC off“ to turn off TMC message as shown in picture 7.4.
RDS-TMC traffice and travel information system 74 TMC messages Once Turbodog received TMC message, it will be displayed literally and marked on the map. Follow the instructions below to view the TMC message: 1. Click on TMC in main menu or Navigation screen to enter as shown in picture 7.7. 2. Select the TMC message header and then click on Info to view the detailed message as shown in picture 7.8. 3.
During navigation, Turbodog will re-calculate a detour to avoid the traffic jam if the traffic event is on the route of a previous route calculation. 1. Picture 7.11 indicates that you have completed a routing and destination setting, press Go to start. 2. During the navigation, Turbodog receives a TMC message indicating there is a traffic condition change on the route. As shown in picture 7.12, the system will prompt you if a detour calculation is preferred.
RDS-TMC traffice and travel information system 76 3. Picture 7.13 shows the result of a detour calculation. PIcture 7.14 is the TMC message.
Navi setting Turbodog provides a various styles in navigation mode. You can setup to use different styles in System Configuration window. 1. Press “Navi setting“ button in Turbodog main Change preference Change preference menu to enter “Navigation Setting“ window. 2. “Navi Setting“ as described below: i.
Change preference This allows you to view driving conditions ahead and makes you always driving to the north. ii. Voice prompt : Turbodog will instruct you at each curving intersection with the provision of voice prompts. Turbodog will not instruct you at each curving intersection with the provision of voice prompts. iii. Auto-zoom in : Turbodog automatically adjusts the ao scale according to driving speed to provide you with better view of the map. Manually adjust mao scale. iv.
v. Simulated speed : This allows you to set a driving speed during a simulated trip. The ranges of simulated speed are 36KM/ Hr, 72KM/Hr, 108KM/Hr, 144KM/Hr and 180KM/Hr, etc. vi. GPS lock : Change preference Turn off “Re-calculate“ function. When your car is stopped or you drive the car very slowly, the cursor of GPS signal will folat on the screen. With this function, you can stop having “moving“ or “floating“ map when you drive at a speed which is slower than a pre-set value.
Change preference Language Menu for general system parameter settings allow you to set up language used for audio prompt, diver side and distance format. 1. Press button in Turbodog main menu to enter “Language“ window. 2. “Language“ page as described below: i. Language: defines the laguage used for audio prompt. ii. Distance Unites: defines measurement system, Metric or U.S. 80 3. After you configure the settings and press will save the settings and return to main menu. , Tibo 4.
MyGuid logs all positioning information received from GPS receiver during navigation. It draws a trail of the track on map. This enables you to review the historic track information when you re-launch Tibo application at the next time. This function is very useful when you drive in rural areas such as desert or forest. 1. Press Change preference Trave record button in Turbodog main menu to enter “Trace Record‘ window. 2. Press navigation. button to turn on/off track logging while 3.
Change preference GPS status Turbodog will check the status of GPS receiver and display the positioning information on the screen of your PDA. This feature of Tibo allows you to view the current usage of satellites, the number of satellites, the position of satellites and the signal strength of satellites, etc. 1. In navigation, click on screen enter “Navi option“ page, then press button to enter “GPS Status“ page. 2. Or in system menu, press button to enter “GPS Status“ page. 3. In GPS Info.
Change preference ii. The signal strength of satellites: the signal strength of satellites from which the signals are received. iii. Positioning infromation: A. Date: the date of which a GPS position fix is received, e.g. 2004/08/30; B. Time: the time of which a GPS position fix is received, e.g. 01:01:27; C. Longitude: the longitude of GPS position fix, e.g. E 121/24/34.456; D. Latitude: the latitude of GPS postion fix, e.g. N 31/24/34.456; E. Altitude: the altitude of GPS position fix, e.g. 17m; F.
Appendix Appendix Categories of POI Turbodog include 19 categories of POI A. All POI B. Automotive C. Business D. Cemetery E. Center of Settlement F. Eduction G. Emergency H. Entertainment I. Food & Drink J. Government office K. Lodging L. Parking M. Petrol Station N. Recreation O. Services P. Shoppping Q. Sights R.
Item Description GPS Global Position System ActiveSync A software application which synchronizes the communication between a PocketPC and a desktop PC Map view mode One of the main function of Tibo which provides map view and map operation Navigation mode One of the main function of Tibo, providing a map view while navigation Menu operation One of the main function of Tibo, providing information query, function set up adn system configuraion Routing Routing calculation between a start point (cu
Appendix 86 Attention * It is not a system failure under circumstances listed below: Problems caused by the characteristics of GPS positioning: • Sometimes, when you are driving on the highway/viaduct, the floating point swings, vice versa. • When you are driving along a Y shaped road, the floating point may brach to the side road. • When you are driving on a road of grid shaped, sometimes you will find that the floating point is at the side road bearby. • When you are driving on a very steep road.
Appendix • Before returning to a ground road after you have been driving in an underground car park or a spiral path of the multi-level car park, you will find that the floating point may swing. When your car is in a rotary elevator, the arrow of the floating point may not point to the right direction. • Providing voice prompt at a branching path ahead even the car is already off the proposed route. • Guiding distance may deviate.
Appendix • If there is only small lanes without a normal road near destination, the system will only guide you to a place near to your destination. • Instruct you to make a U-turn, • No indication at a branching road. • Turning instruction mismatch the real road condition. • No indication of direction or voice prompt about entrance/exit while guiding on highway/express way. • Schematic map may mismatch real road conditions.
Appendix • The floating point may swing when you use the system at the first time after installation. • The floating point may swing when you are changing the tyre, specially using a spare tyre. • The system will automatically adjust its position and direction using GPS signals when the floating point mismatches real condition. Map icons Icon Name Icon Name District/Estate Police station/NPP Building.
Appendix Icon Name Icon Name School/Education centre Airport Sports Embassy/Town council Cinema/Libary Religion Golf Exhibition/Company TMC message icons Icon Name 90 Icon Name queuing traffic expected (Q) accident(s). Stationary traffic for 3km accident. Delays(Q) this service provides major road information heavy snowfall stationary traffic for 3km cyclists on roadway. Danger major event.
Icon Name allow emergency vehicles to pass (Q sets of) roadworks. Slow traffic contraflow. Queuing traffic less than 10 parking spaces available no motor vehicles carriageway reduced (from Q lanes) to one lane message cancelled incident cleared Appendix Icon Name (Q) lanes closed.
Camera Camera Your Hatchback has an inbuilt camera, which allows you to take photos and save as a geographical location. Photos can be saved in the Photo Viewer on Hatchback or a memory card and viewed in full screen. Activating camera You can take photos with this inbuilt camera and access the camera preference. Do one of the following to view the camera screen: • Press the camera button back. • Or tap the camera icon 92 on the top of the Hatchin the main menu.
1 2 Description Display the save location and the number of photos that are still can be taken / 3 Camera Element Tap to adjust the lighting and brightness Press to get the sub menu: - Tap it to access the Photo Viewer - Tap to select the save location: Internal memory/External memory card - Tap to turn shutter on/off - Tap to adjust the white balance status 4 5 6 Battery indicator Viewfinder Allows you to take photo within the viewfinder Return to main menu Customizing camera preferences You’d be
Camera Lighting and brightness options To adjust the lighting and brightness as the following steps: 1. When the camera is open, tap / to adjust the lighting and brightness. 2. Stop until the lighting is your preferred one. Save location options The photo can be saved on Hatchback or memory card. To set the save location as the following: 1. When the camera is open, tap 2. Tap to get the sub menu. to select Save to internal memory or Save to external memory card in the popup menu.
Before you take a photo you can customize the lighting and brightness settings. For more information, see “Customizing camera preferences“. 1. When the camera is open, an image the camera is focused on will display in the viewfinder. 2. When you are satisfied with the image displayed in the viewfinder, press the camera button Camera Taking a photo to take the photo. 3. The captured photo will be automatically saved in the Photo Viewer on Hatchback or memory card.
Photo Viewer Photo Viewer The Photo Viewer stores all your photos and displays them as thumbnails. You can store photos in the Photo Viewer on Hatchback or memory card. Accessing Photo Viewer You can manage only the photos saved in DCIM/HatchBack. Do one of the following to activate Photo Viewer: • Tap the Photo Viewer icon in the main menu. • Or when the camera is open, tap Viewer.
Description Photo Display photos in the Photo Viewer on Hatchback or memory card. Tap to display in full screen. 2 Display if GPS is associated with a photo 3 You are in the Photo Viewer 4 Tap to activate camera 5 6 7 Scroll bar Photo Viewer 1 Element Allows you to scroll through thumbnail view of photos Tap to switch to memory card Return to main menu Photo management To manage a photo, you need to tap the thumbnail of the photo. The photo will display in full screen.
Photo Viewer Element Description 98 1 Tap to view the photo’s information 2 If GPS is associated with the photo, tap it to activate GPS application 3 Tap to rotate the photo 4 Tap it to select related options (See the following instruction) 5 Return to main menu 6 Tap to view the previous photo 7 Tap to view the next photo
1. Tap to access the Photo Information screen. 2. You can see the file name, photo description, taken date, and size. If the GPS is associated with the photo, the longitude and latitude will be displayed at the bottom of the Photo Information screen. 3. Tap tap Photo Viewer To view a photo’s information to edit the file name and photo description; to save. To go to navigation This function is only available when the GPS is associated with this photo. 1.
Photo Viewer 2. If the photo is saved in memory card, tap to select Move to internal memory/Copy to internal memory. Note: When copy/move photos to Hatchback, all photos will be saved in the following folder: DCIM/HatchBack. To delete a photo 1. In the full view screen of a photo, tap Delete. 2. Tap 100 to delete the current photo.
Activating Mp3 Player From the main menu, tap Mp3 Player Mp3 Player to activate Mp3 player. You will see the options in the Mp3 Player screen: playlists, artists, album, songs and now playing. • Tap before Now Playing to access playing screen. • Tap after Playlist, Artists, Albums and Songs to access the submenu.
Mp3 Player Playing a song You have several ways to play a song. Playing a song from Now Playing 1. In the Mp3 Player screen, tap to access playing screen. 2. Tap to play a song, tap before Now Playing to pause. 3. Tap to play the previous song; tap next song. Number of songs Progress bar Play mode to play the Settings Time Playing a song from Playlists 1. In the Mp3 Player screen, tap access Playlists screen. 2. Select a playlist to access it.
Mp3 Player -- Tap to play a song. -- Tap to select the sort mode: Artist, Title and As created. -- Tap to remove the current song. (Attention: Just remove the current song from the playlist.) -- Tap to add audio files from the audio file list. Playing a song from Artists 1. In the Mp3 Player screen, tap the submenu. after Artists to access 2. If select All in the submenu, only can tap songs. 3.
Mp3 Player You also can play songs from Albums or Songs, it is quite the same as Artists. Deleting a song Deleting a song from Playlists 1. In the Mp3 Player screen, tap access Playlists screen. 2. Select a playlist to access it. after Playlists to 3. Tap to delete the current song. (Attention: Just remove the current song from the playlist.) Deleting a song from Artists/Albums/Songs 1. In the Mp3 Player screen, tap after Artists/Albums/ Songs to access the submenu. 2.
In Mp3 player, you can customize your own playlist to save your preferred songs. Mp3 Player Playlist management Creating a new playlist Do as the following steps to create a new playlist: 1. In the Playlist screen, select New Playlist. Tap it again to hide the handwriting panel Tap to add songs into the playlist Tap to cancel 2. Edit the playlist name with the handwriting panel. 3. Tap to access the Add Media screen. 4. Select the audio files/songs you want to add into the new playlist.
Mp3 Player Note: No playlist will be created if no songs are added into the new playlist. The check box will be grey if you just select some of the songs saved in the file. Deleting a playlist From the Playlists, select a playlist you want to delete. Tap delete the selected playlist.
Before playing songs, you can make a configuration. Setting play mode 1. In the playing screen, tap to get the popup menu. Mp3 Player Mp3 Player settings 2. Select Play Mode to activate the Shuffle and Loop On/ off.
Hatchback configuration Hatchback configuration Customizing Hatchback To change Hatchback settings, tap in the main menu, see the following description for more information. Changing the time/date settings In the Setting screen, tap to access Time/Date screen. You can set time, date and other related setting. • Set Time: Select am/pm; Tap the hour/minute box and change the time via the up/down arrow. • Time Format: Choose a 12-hour or 24-hour time format.
Hatchback configuration • Set Date: Tap the down arrow to select your date in the popup calendar. • Date Format: Choose your preferred date format. • Set Time Zone: Tap the down arrow to select a time zone in the pull down menu. • Daylight saving: Select the check box to set it on. • Synchronize with GPS: Select the check box; the current time and date will update automatically with GPS satellite.
Others Others Using World Clock This application allows you to set multi-international time zone. Accessing World Clock To activate World Clock, tap 1 110 in Utility. Element Description Local time zone area The local time cannot be set here. You can set it in the Time/Date from Setting.
Description Int’l time zone area Tap to set the int’l time zone 3 Tap to enable daylight saving function 5 Tap to view the tutorial for World Clock 6 Return to Utility menu Others 2/4 Element Time zone area settings The local time setting • You cannot set the local time in World Clock. If you need to reset the local time, please set it in Time/Date from Setting application. (See page xxx.
Others 2. Select a zone area displayed in the Europe country list you need in Set Time Zone screen; double click on a country and return to World Clock. 3. The new selected int’l time zone area displays. Switching three time zone area randomly The local time zone area and the two int’l time zone area can be switched mutually. • For example, to change the current local time zone area to be the int’l time zone area.
Others Element Description 1 Make a simple calculation (plus, minus, multiplication or division ) 2 Currency conversion 3 Unit conversion.
