Installation Instructions

ManualsBrandsGrohe ManualsHouseholdPush open

.....1

.....6

.....11

.....16

.....21

.....26

.....2

.....7

UAE

.....12

.....17

EST

.....22

.....27

.....3

.....8

.....13

.....18

.....23

RUS

.....28

.....4

.....9

.....14

SLO

.....19

.....24

.....5

FIN

...10

.....15

.....20

.....25

DESIGN + ENGINEERING

GROHE GERMANY

www.grohe.com

34 438

34 557

34 439

GROHTHERM 1000 NEW

99.0270.031/ÄM 231304/04.15

.....1

.....6

....11

....16

....21

....26

.....3

.....7

UAE

....12

....17

EST

....22

RUS

....27

.....3

.....8

....13

....18

....23

RUS

...10

.....4

.....9

....14

SLO

....19

....24

.....5

FIN

....10

....15

....20

....25

Summary of content (10 pages)

PAGE 1
GROHTHERM 1000 NEW DESIGN + ENGINEERING GROHE GERMANY 99.0270.031/ÄM 231304/04.15 www.grohe.com 34 438 34 557 34 439 D GB F GB F E I .....1 .....2 .....3 NL .....6 S .....7 .....3 DK .....8 .....4 ....14 SLO .....19 ....19 LT ....24 .....24 CZ .....14 ....10 H ....15 .....15 HR ....20 .....20 RO ....25 .....25 FIN ...10 .....5 N .....9 .....11 PL ....11 P .....16 BG ....21 ....16 .....21 CN ....26 .....26 .....12 TR .....17 ....17 EST .....22 ....22 RUS UAE ....12 UA .....27 ....27 .....13 .
PAGE 2
34 438 34 557 1 22mm 30mm 36-42 2 34 439 * 19 001 3 Please pass these instructions on to the end user of the fitting! S.v.
PAGE 3
II
PAGE 4
Notes GB High pressure. If there is a residual flow during the commissioning or the annual verification (cold water supply isolation test), then this is acceptable providing the temperature of the water seeping from the valve is no more than 2°C above the designated maximum mixed water outlet temperature setting of the valve. Conditions of use TMV2 Application Safety and important information This thermostatic valve will suit supplies of: high pressure max.
PAGE 5
Installation Maintenance Flush piping system prior and after installation of fitting thoroughly (Consider EN 806)! Inspect and clean all parts, replace if necessary and lubricate with special valve grease. Install unions and screw-mount the mixer, see fold-out page I, Fig. [1]. Shut off the hot and cold water supply. Non-return valve, see fold-out page III, Fig. [7]. Refer to the dimensional drawing on fold-out page I. Remove connection nipple using a 12mm allen key.
PAGE 6
Réglage F Réglage de la température, voir volet I fig. [2]. Domaine d'application Les robinetteries thermostatiques sont conçues pour fournir de l'eau chaude avec des accumulateurs sous pression et permettent d'obtenir une température de l'eau extrêmement précise. Si la puissance est suffisante (à partir de 18 kW, ou 250 kcal/min), des chauffe-eau instantanés électriques ou au gaz conviennent également. Limitation de la température La température est limitée à 38 °C par le verrouillage de sécurité.
PAGE 7
4 max. min.
PAGE 8
34mm *19 332 9 19mm 10 11 17mm II IV
PAGE 9
PAGE 10
D & +49 571 3989 333 impressum@grohe.de A & +43 1 68060 info-at@grohe.com AUS Argent Sydney & +(02) 8394 5800 Argent Melbourne & +(03) 9682 1231 B & +32 16 230660 info.be@grohe.com BG & +359 2 9719959 grohe-bulgaria@grohe.com CAU & +99 412 497 09 74 info-az@grohe.com CDN & +1 888 6447643 info@grohe.ca CH & +41 448777300 info@grohe.ch CN & +86 21 63758878 CY & +357 22 465200 info@grome.com CZ & +420 277 004 190 EST & +372 6616354 grohe@grohe.