MEAT GRINDER MODEL H6247 INSTRUCTION MANUAL COPYRIGHT © SEPTEMBER, 2004 BY GRIZZLY INDUSTRIAL, INC. WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
SAFETY For Your Own Safety Read Instruction Manual Before Operating This Equipment The purpose of safety symbols is to attract your attention to possible hazardous conditions. This manual uses a series of symbols and signal words which are intended to convey the level of importance of the safety messages. The progression of symbols is described below. Remember that safety messages by themselves do not eliminate danger and are not a substitute for proper accident prevention measures.
6. ONLY ALLOW TRAINED AND PROPERLY SUPERVISED PERSONNEL TO OPERATE MACHINERY. Make sure operation instructions are safe and clearly understood. 7. KEEP CHILDREN AND VISITORS AWAY. Keep all children and visitors a safe distance from the work area. 8. 9. 13. ALWAYS DISCONNECT FROM POWER SOURCE BEFORE SERVICING MACHINERY. Make sure switch is in OFF position before reconnecting. 14. MAKE WORKSHOP CHILD PROOF. Use padlocks, master switches, and remove start switch keys. MAINTAIN MACHINERY WITH CARE.
Additional Safety Instructions For Meat Grinders 1. READ THIS MANUAL: This manual contains proper operating instructions for this machine. 5. LOOSE CLOTHING: DO NOT wear loose clothing while operating this machine. Tie back long hair. 2. ALWAYS CLEAN AND SANITIZE ALL PARTS THAT COME IN CONTACT WITH MEAT DURING PROCESSING. 6. SHARP SURFACES: DO NOT place hands near, or in contact with, cutting surfaces during operation. 3.
INTRODUCTION Foreword Contact Info We are proud to offer the Grizzly Model H6247 Meat Grinder. This model is part of a growing Grizzly family of fine power tools. When used according to the guidelines set forth in this manual, you can expect years of trouble-free, enjoyable operation and proof of Grizzly’s commitment to customer satisfaction.
SET UP Inventory Unpacking Your machine left our warehouse in a carefully packed crate or box. If you discover the machine is damaged after you have signed for delivery, please immediately call Customer Service at (570) 5469663 for advice. Save the containers and all packing materials for possible inspection by the carrier or its agent. Otherwise, filing a freight claim can be difficult. When you are completely satisfied with the condition of the shipment, you should inventory the equipment.
Assembling Grinding Head 1. Loosen the locking ring, and remove the barrel from the grinding motor housing. 2. Unscrew the lock ring and remove the cutting plate, cutting blade, and feed screw. Thoroughly sanitize the grinder head and throat, barrel, cutting plates, cutting blade, feed screw, lock ring, locking knob and hopper (refer to Proper Sanitization on page 9). 3. 4. Before proceeding with assembly, wipe down the outside surface of grinder motor housing with a sanitized cloth. 5. Figure 3.
. Twist the feed screw so the vertical slot on the feed screw aligns with the vertical shaft on the inside of the grinder head. 10. Slide the assembly into the grinder head. Use the pin on the side of the barrel as a guide into the slot. Note– The vertical slot on the back of the feed screw must align with the vertical shank inside the grinder head (Figure 5). Controls ON/OFF and REVERSE Switch (Figure 6): Figure 6. Switch location 1. Turn the switch to the right to turn the motor ON. 2.
OPERATIONS Grinding If a jam occurs: 1. Rotate the REVERSE switch once or twice to attempt to free the jam. The Model H6247 is designed for meat processing. DO NOT attempt to grind bone or hard foods like nuts or fibrous foods like celery or ginger. If you cannot clear a jam by using the reverse switch: 1. 1. UNPLUG THE GRINDER FROM THE POWER SOURCE! 2. Disassemble the grinding head and remove the material jamming the cutter or feed screw. 3.
CLEANING & LUBRICATION Proper Sanitation 2. All surfaces and working parts that have been exposed to meat must be properly sanitized before and after each use. Prepare the sink. Wash and scrub all sink compartments with dish soap and hot water. Rinse these compartments thoroughly. 3. Fill a sink with soapy water, submerge the item and scrub the entire surface thoroughly. 4. Using hot water, rinse the newly cleaned item until all visible suds have been removed.
Cleaning the motor housing: Lubrication: 1. UNPLUG THE MOTOR FROM THE POWER SOURCE! 2. Wipe down the exterior surface of the motor with a cloth soaked in a sanitizing solution. DO NOT submerge the motor in water! The Model H6247 requires very little lubrication. The following steps on the grinder head parts will keep them moving freely and keep them from oxidizing. 3. Pay particular attention to the throat and grinder head portion of the meat grinder.
Parts Breakdown � � � � � � � � �� � REF 1 2 3 4 5 6 7 8 9 10 PART # PH6247001 PH6247002 PH6242003 PH6247004 PH6247005 PH6247006 PH6247007 PH6247008 PH6247009 PH6247010 Model H6247 Meat Grinder DESCRIPTION GRINDER MOTOR HOUSING MEAT PUSHER HOPPER BARREL FEED SCREW CUTTING BLADE CUTTING PLATE FINE LOCKING RING CUTTING PLATE COURSE LOCKING KNOB M8-1.
WARRANTY AND RETURNS Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance.
WARRANTY CARD Name _________________________________________________________________________ Street ________________________________________________________________________ City____________________State________Zip_________ Phone Number____________E-Mail___________________FAX ____________ Model # H6248 Meat Grinder Serial#________________Order #____________ The following information is given on a voluntary basis. It will be used for marketing purposes to help us develop better products and services.
Send a Grizzly Catalog to a friend: Name________________________________ Street________________________________ City______________State______Zip_______ FOLD ALONG DOTTED LINE Place Stamp Here GRIZZLY INDUSTRIAL, INC. P.O.
