MODEL G0756 INDUSTRIAL DRILL PRESS OWNER'S Manual (For models manufactured since 03/13) Copyright © MAY, 2013 By Grizzly Industrial, Inc., Warning: No portion of this manual may be reproduced in any shape Or form without the written approval of Grizzly Industrial, inc.
This manual provides critical safety instructions on the proper setup, operation, maintenance, and service of this machine/tool. Save this document, refer to it often, and use it to instruct other operators. Failure to read, understand and follow the instructions in this manual may result in fire or serious personal injury—including amputation, electrocution, or death. The owner of this machine/tool is solely responsible for its safe use.
Table of Contents INTRODUCTION................................................ 2 Machine Description....................................... 2 Contact Info.................................................... 2 Manual Accuracy............................................ 2 Identification.................................................... 3 Control Panel.................................................. 4 Machine Data Sheet....................................... 5 SECTION 1: SAFETY.............................
INTRODUCTION Machine Description Manual Accuracy We are proud to offer the Model G0756 18-speed Heavy-Duty Drill Press. When used according to the guidelines set forth in this manual, you can expect years of trouble-free, enjoyable operation and proof of Grizzly’s commitment to customer satisfaction. We are proud to provide a high-quality owner’s manual with your new machine! This drill press features power tapping with an electronic clutch and activation buttons on the downfeed handles.
Identification C B K D A L E F M J N I H G A. Main Power Switch B. Lifting Eye Bolt C. Motor D. Speed Control Levers E. Control Panel (see Page 4 for details) F. Chip Guard G. Coolant Pump Model G0756 (Mfg. Since 2/13) H. Automatic Drift I. Automatic Downfeed Adjustment Knob J. Coolant Nozzle K. Oil Site Glass L. Coarse Downfeed Handles M. Table Lock Handles N.
Control Panel A B F C G D H I E Figure 1. Control panel A. Spindle Speed Levers: Used to get spindle speed at available RPMs. F. B. Coolant Pump Switch: Turns pump on, sending coolant to nozzle G. EMERGENCY STOP Button: Immediately cuts power to motor and control panel when pressed. Remains depressed until button is reset by twisting clockwise. C. High/Low Spindle Speed Range Switch: Selects high/low range for spindle speed. Working Lamp Switch: Turns work light on or off. D.
Machine Data Sheet MACHINE DATA SHEET Customer Service #: (570) 546-9663 · To Order Call: (800) 523-4777 · Fax #: (800) 438-5901 MODEL G0756 HEAVY-DUTY DRILLING MACHINE Product Dimensions: Weight............................................................................................................................................................ 1026 lbs. Width (side-to-side) x Depth (front-to-back) x Height..................................................................... 22 x 37 x 89-1/2 in.
Main Specifications: Operation Info Spindle Travel.............................................................................................................................................. 7 in. Max Distance Spindle to Column........................................................................................................ 13-3/4 in. Max Distance Spindle to Table............................................................................................................ 30-3/4 in.
SECTION 1: SAFETY for your Own Safety, Read Instruction Manual before Operating This Machine The purpose of safety symbols is to attract your attention to possible hazardous conditions. This manual uses a series of symbols and signal words intended to convey the level of importance of the safety messages. The progression of symbols is described below. Remember that safety messages by themselves do not eliminate danger and are not a substitute for proper accident prevention measures.
WEARING PROPER APPAREL. do not wear clothing, apparel or jewelry that can become entangled in moving parts. Always tie back or cover long hair. Wear non-slip footwear to avoid accidental slips, which could cause loss of workpiece control. hAzARDOUS DUST. dust created while using machinery may cause cancer, birth defects, or long-term respiratory damage. Be aware of dust hazards associated with each workpiece material, and always wear a niosh-approved respirator to reduce your risk. hEARING PROTEcTION.
Safety for Drill Presses EYE/FACE/HAND PROTECTION. A face shield used with safety glasses is recommended. Always keep hands and fingers away from the drill bit. Never hold a workpiece by hand while drilling! DO NOT wear gloves when operating the drill. SECURING BIT. Properly tighten and securely lock the drill bit in the chuck. CORRECT BIT. Use only round, hex, or triangular shank drill bits. ADJUSTING KEYS AND WRENCHES. Remove all adjusting keys and wrenches before turning the machine ON.
SECTION 2: POWER SUPPLY Availability Circuit Requirements for 220V Before installing the machine, consider the availability and proximity of the required power supply circuit. If an existing circuit does not meet the requirements for this machine, a new circuit must be installed. To minimize the risk of electrocution, fire, or equipment damage, installation work and electrical wiring must be done by an electrican or qualified service personnel in accordance with all applicable codes and standards.
Grounding Instructions This machine MUST be grounded. In the event of certain malfunctions or breakdowns, grounding reduces the risk of electric shock by providing a path of least resistance for electric current. The power cord and plug specified under “Circuit Requirements for 220V” on the previous page has an equipment-grounding wire and a grounding prong.
SECTION 3: SETUP Unpacking Inventory Your machine was carefully packaged for safe transportation. Remove the packaging materials from around your machine and inspect it. If you discover any damage, please call us immediately at (570) 546-9663 for advice. The following is a list of items shipped with your machine. Before beginning setup, lay these items out and inventory them. Save the containers and all packing materials for possible inspection by the carrier or its agent.
Cleanup the unpainted surfaces of your machine are coated with a heavy-duty rust preventative that prevents corrosion during shipment and storage. this rust preventative works extremely well, but it will take a little time to clean. Be patient and do a thorough job cleaning your machine. the time you spend doing this now will give you a better appreciation for the proper care of your machine's unpainted surfaces.
Site Considerations Weight Load Physical Environment Refer to the Machine Data Sheet for the weight of your machine. Make sure that the surface upon which the machine is placed will bear the weight of the machine, additional equipment that may be installed on the machine, and the heaviest workpiece that will be used. Additionally, consider the weight of the operator and any dynamic loading that may occur when operating the machine.
Lifting & Placing hEAvy LIfT! Straining or crushing injury may occur from improperly lifting machine or some of its parts. To reduce this risk, get help from other people and use a fork lift (or other lifting equipment) rated for weight of this machine. To move and place this drill: 1. Place shipping crate near final machine mounting location. 2.
Arbor/Chuck Assembly An arbor is included for the drill chuck that comes with this machine. The following procedure describes how to install the arbor in the chuck. After the arbor is installed in the drill chuck, it is very difficult to separate the assembly. If you would like to use a different chuck in the future, we suggest using a different arbor. Important: DO NOT install the drill chuck and arbor assembly until AFTER the test run.
Power Connection 2. 20-21 = 220V 20-22 = 230V 20-23 = 380V 20-24 = 400V 20-25 = 415V 20-26 = 440V QM5 QM3 C1 ON Transformer OFF JBK5-100VATH QM2 C3 ON D1 ON OFF OFF TC Identify L2, 34 and 35 L3 terminals and the 30 31the32L1,33 E grounding terminal (see Figure 9). 20 21 30 31 10 32 11 12 3. Thread the power cord through the strain relief shown in Figure 9. Electrocution or fire may occur if machine is ungrounded, incorrectly connected to power, or connected to an undersized circuit.
5. 6. Make sure the power cord and wires have slack between the strain relief and terminal connections so that they do not bind, then tighten the strain relief to secure the cord. If, during the test run, you cannot easily locate the source of an unusual noise or vibration, stop using the machine immediately, then review Troubleshooting on Page 35. Note: The strain relief must be tightened against the outer jacket of the cord.
4. Press the EMERGENCY STOP button (Figure 12) in, then twist it clockwise so it pops out. When the botton pops out the switch is reset and ready for operation. EMERGENCY STOP Button Spindle Start Button Spindle Stop Button Figure 12. Resetting the switch. 5. 6. Press the EMERGENCY STOP button and ensure that the drill press comes to a complete stop. 7. WITHOUT resetting the EMERGENCY STOP button, press the spindle start button. The machine should not start.
Test Coolant System This drill press comes with a pump-driven cycling coolant system. Prior to testing the coolant system, add two gallons of coolant to the coolant reservoir. Refer to Changing Coolant on Page 28. 3. Turn the Coolant Pump Switch to the ON position. 4. Adjust the ball valve in the coolant nozzle assembly for the proper coolant flow (see Figure 14). Ball valve To test the coolant system: 1. Wear safety goggles and other protective clothing. 2.
Spindle Break-In To perform the spindle break-in procedure: 1. Before subjecting the spindle to operational loads, it is essential to complete the break-in process. This helps ensure maximum life of spindle bearings and other precision components by thoroughly lubricating them before placing them under load. Move the drilling & tapping switch to the drilling position (see Figure 15).
SECTION 4: OPERATIONS Operations Overview The purpose of this overview is to provide the novice machine operator with a basic understanding of how the machine is used during operation, so the machine controls/components discussed later in this manual are easier to understand. Due to the generic nature of this overview, it is not intended to be an instructional guide.
Installing Tapered Tooling 3. While holding onto the tooling, raise the spindle to the original position. It should automatically release from the spindle. 1. DISCONNECT MACHINE FROM POWER! 2. Clean tooling and spindle tapers to ensure proper seating. 3. Insert the MT#4 tooling into the spindle, and maneuver the tang until it engages with the slot at the end of the spindle. 1. Use a rubber or wooden mallet to seat the tooling into the spindle by firmly tapping from the bottom. 2.
Depth Stop 7. Press the spindle start button. 8. This drill press includes a depth stop for drilling multiple holes at the same depth. Drill a hole into scrap stock before drilling into any workpiece to ensure the depth has been set correctly. If necessary, repeat Steps 2–5. Table Positioning To set the depth stop: 1. DISCONNECT MACHINE FROM POWER! 2. Adjust the table height so the workpiece is close to the work tool. 3.
Selecting Spindle RPM Note: For carbide cutting tools, double the cutting speed. These values are a guideline only. Refer to the MACHINERY'S HANDBOOK for more detailed information. Use the proper spindle speed and feed rate to reduce strain on all moving parts and decrease risk of operator injury. Prior to drilling, determine the RPM needed for workpiece material then set the spindle speed to the closest available RPM.
Drilling Mode To drill a workpiece: 1. This drill press is designed for vertical drilling and tapping operations. For repeated drilling at the same depth, there is a power downfeed mechanism. For tapping convenience, there is an automatic clutch used for reversing the direction of the spindle while in tapping mode by pressing one of the buttons at the ends of each course downfeed handle.
Automatic Power Downfeed This drill press comes with automatic downfeed control for repeated drilling operations at the same depth. The automatic downfeed only works in the drilling mode. 4. Match the lines on the adjustment knob to select an automatic power downfeed option (see Figure 24). —There are three options for the power downfeed mechanism that are located on the side of the adjustment knob: • • Stay clear of coarse downfeed handles while using the automatic downfeed.
Tapping Mode Coolant System When in tapping mode, the spindle direction can immediately alternate between forward and reverse by pressing any of the three buttons at the end of the downfeed handles. This feature is critical to back the tap out of a hole before it bottoms out and snaps off, as well as clearing away waste chips during the tapping process. This machine comes with a coolant system for use in drilling and tapping operations. This feature promotes precision cutting and tool longevity.
SECTION 5: ACCESSORIES Installing unapproved accessories may cause machine to malfunction, resulting in serious personal injury or machine damage. To reduce this risk, only install accessories recommended for this machine by Grizzly. G1075—52-PC. Clamping Kit This clamping kit includes 24 studs, 6 step block pairs, 6 T-nuts, 6 flange nuts, 4 coupling nuts, and 6 end hold-downs. The rack is slotted so it can be mounted close to the machine for easy access. Made for 1⁄ 2" T-slots.
T23962—ISO 68 Moly-D Way Oil, 5 gal. T23963—ISO 32 Moly-D Machine Oil, 5 gal. Moly-D oils are some of the best we've found for maintaining the critical components of machinery because they tend to resist run-off and maintain their lubricity under a variety of conditions—as well as reduce chatter or slip. Buy in bulk and save with 5-gallon quantities. T23962 G3658—Titanium Drill Bits Titanium nitride-coated bits last up to six times as long as uncoated bits.
H7819—Drill & Tap HSS 24 pc. Set Our new High Speed Steel Tap and Drill Set comes supplied with 6 of the most commonly used coarse thread sizes. What's more, each size has taps with plug, bottoming and taper grinds allowing you to choose the right tap for any job. The set includes the following tap sizes and corresponding drill bits: 8-32 & #29, 10-24 & #25, 1⁄4"-20 & #7, 5 ⁄ 16"-18 & F, 3 ⁄ 8"-16 & 5 ⁄ 16" and 1⁄ 2"-13 & 27⁄ 64".
SECTION 6: MAINTENANCE Daily, After Operations To reduce risk of shock or accidental startup, always disconnect machine from power before adjustments, maintenance, or service. Schedule • Thoroughly clean the machine and protect all surface areas • Press the EMERGENCY STOP button and shut OFF the master power switch (to prevent accidental startup). • Remove any rotary tables, vises, fixtures, or workpieces from the table to prevent rusting the table surface.
Lubrication For the quill, table, and column, an occasional application of light machine oil is all that is necessary. Before applying lubricant, clean off any dust or metal chips. Do not fill headstock with oil above the red mark. This could damage the machine and create an overflow of oil. Your goal is to achieve adequate lubrication. Too much lubrication will attract dirt and dust. Various parts of your machine could lose their freedom of movement as a result. Red Mark Headstock Lubrication Oil Type.
Changing Coolant Ball Oilers Oil Type.......Model T23963 or ISO 32 Equivalent Oil Amount.......................................... 1–2 Pumps Lubrication Frequency.........8 Hours of Operation This machine has four ball oilers as shown in Figures 38–39. Use an oil gun fitted with a rubber tip wide enough to seal the ball oiler inlet. We do not recommend using metal needle or lance tips, as they can push the ball too far into the oiler, break the spring seat, and lodge the ball in the oil galley.
SECTION 7: SERVICE Review the troubleshooting and procedures in this section if a problem develops with your machine. If you need replacement parts or additional help with a procedure, call our Technical Support at (570) 546-9663. Note: Please gather the serial number and manufacture date of your machine before calling. Troubleshooting Motor & Electrical Symptom Possible Cause Machine does not 1. Emergency stop push-button engaged/at start or a breaker fault. trips 2.
Drill Press Operations Symptom Possible Cause Possible Solution Breaking tools or cutters. 1. Spindle speed/feed rate is too fast. 1. Set spindle speed correctly (Page 25) or use a slower feed rate. 2. Use coolant or oil for appropriate application. 3. Fully retract spindle and lower headstock. This increases rigidity. 2. Cutting tool getting too hot. 3. Spindle extended too far down. Drilling stops, but the motor 1. Bit slips in chuck. still operates. 1.
Replacing Lamp Bulb The work lamp bulb in this machine is a 24V 25W two pronged halogen bulb. The replacement part number for the bulb is P0756418-1. To replace the bulb in the work lamp: 1. Torque Limiter The torque limiter regulates how much torque is applied to the drive shaft of the drill press to prevent the machine from mechanical overload. It was adjusted at the factory according to the maximum axial load. Eventual wear on the limiter discs may require compensatory adjustment to the torque limiter.
machine SECTION 8: WIRING These pages are current at the time of printing. However, in the spirit of improvement, we may make changes to the electrical systems of future machines. Compare the manufacture date of your machine to the one stated in this manual, and study this section carefully. If there are differences between your machine and what is shown in this section, call Technical Support at (570) 546-9663 for assistance BEFORE making any changes to the wiring on your machine.
Wiring Overview Spindle Motor Page 41 Control Panel Page 43 Master Power Switch Page 45 Electrical Panel Page 45 Coolant Pump Motor Page 41 Elevation Limit Switches Page 43 Chip Guard Limit Switch Page 43 Electronic Clutch Page 40 Work Lamp Page 41 Power Supply Connection Page 40 Component Location Index Spindle Motor Page 41 Master Power Switch Page 45 Electrical Panel Page 45 b Power Plug Page i40 Control Panel Page 43 d Elevation Limit Switches Page 43 Chip Guard Limit Switch Page 43 Work Lamp
Power Connection Wiring Hot Ground Hot G X Z W Hot 220 VAC 3-Phase 15-15 Plug (as recommended) Electric Clutch Wiring To Electrical Panel Page 45 13 QO Gd. PE Ground Front View Side view Figure 43. Electronic clutch wiring. -40- READ ELECTRICAL SAFETY ON PAGE 38! Model G0756 (Mfg.
Motor & Pump Wiring To Control Panel Page 43 U1 W2 V1 U2 W1 V2 Ground PE SPINDLE MOTOR Figure 44. Spindle motor wiring. Ground PE V2 W1 U2 U2 V1 V2 W2 U1 W2 To Electrical Panel Page 45 PUMP MOTOR WORK LAMP To Control Panel Page 43 Figure 45. Coolant pump wiring. 13 10 Figure 46. Work lamp wiring. Model G0756 (Mfg.
Control Panel To Lamp Page 41 To Electrical Panel Page 45 To Electrical Panel To Spindle Motor Page 45 Page 41 PE Ground 12 X5 X6 C2SS2-10B-10 C2SS2-10B-10 LAMP SWITCH PUMP SWITCH Left View X6 LX5W-A11N Upper Elevation Limit Switch V1 U1 4 2 8 6 12 10 16 14 W2 2 W1 MCB-01 Right View 1 U1 U2 V1 V2 1 3 5 7 9 111315 EMERGENCY STOP W1 HIGH/LOW GEAR SWITCH X2 X4 C2SS2-10B-10 C2SS2-10B-10 DRILLING/TAPPING SWITCH 10 SPINDLE DIRECTION 12 COM LX5W-A11N X7 4 X1 MCB-01 CP1-10R-01
Control Panel & Limit Switches Chip Guard Limit Switch Upper Elevation Limit Switch Figure 47. Chip Guard limit switch location. Lamp Switch Pump Switch Emergency Stop Button High/Low Gear Switch Drilling/Tapping Mode Switch Spindle Direction Switch Start Button Stop Button Lower Elevation Limit Switch Figure 31. Control panel and limit switch locations (viewed from behind). Model G0756 (Mfg.
Electrical Panel Wiring Master Power Switch 3L1 31 11 2L1 L1 2L3 L2 L3 8 6 21 4 2 L3 26 25 20-21 = 220V 20-22 = 230V 20-23 = 380V 20-24 = 400V 20-25 = 415V 20-26 = 440V 24 23 22 21 DZ451-63 DZ451-63 20 QM5 QM3 C1 ON Transformer QM2 C3 ON OFF JBK5-100VATH DZ451-63 D1 ON OFF DZ451-63 D10 ON OFF L1 DZ451-63 QM1 QM4 C1 ON OFF 31 32 33 34 35 20 21 30 31 10 11 E 32 12 3L1 3L3 2L1 R OFF TC 30 ZL2 22 2L3 L L3 7 5 3 1 L2 L1 CanSen 3L3 LW26GS-20 L
Electrical Wiring Panel Photo Figure 48. Electrical wiring panel. Model G0756 (Mfg.
SECTION 9: PARTS Table Support & Coolant Breakdown 14 34 33 13 11 10 32 9 8 29 15 30 16 28 27 26 7 6 17 31 5 19 4 18 25 3 20 24 2 23 22 21 1 Please Note: We do our best to stock replacement parts whenever possible, but we cannot guarantee that all parts shown here are available for purchase. Call (800) 523-4777 or visit our online parts store at www.grizzly.com to check for availability. -46- Model G0756 (Mfg.
Table Support & Coolant Parts List REF PART # DESCRIPTION REF PART # DESCRIPTION 1 2 3 4 5 6 7 8 9 10 11 13 14 15 16 17 18 BASE COOLANT PUMP MOUNT CAP SCREW M6-1 X 12 COOLANT PUMP CAP SCREW M6-1 X 12 HANDLE SHAFT 3/8"-16 x 3" CRANK ARM SET SCREW M10-1.5 X 10 PILOT CLAMP COLLAR WORM GEAR M16-2 ADJUSTABLE HANDLE M16 X 114 CAP SCREW M6-1 X 60 HEADSTOCK MOUNT GEAR 15T CAP SCREW M8-1.
Gearbox Breakdown 101 102-1 102-3 103 104 134 102-2 133 102-4 102-5 102 132 105 131 106 107 130 129 128 127 108 126 109 125 135 124 110 111 136 112 113 123 114 122 121 -48- 115 119 118 117 114 116 Model G0756 (Mfg.
Gearbox Breakdown 2 142 151 141 139 140 148 138 137 147 146 145 144 143 150 149 158 157 156 155 153 164 155 154 154 156 152 163 162 161 159 172 160 170 167 165 168 155 171 169 156 166 178 179 155 180 176 177 173 174 Model G0756 (Mfg.
Gearbox Parts List REF PART # DESCRIPTION REF PART # DESCRIPTION 101 102 102-1 102-2 102-3 102-4 102-5 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 GEARBOX HOUSING MOTOR 2HP 220V 3-PH 4/8-POLE MOTOR FAN COVER MOTOR FAN JUNCTION BOX FRONT MOTOR BEARING 6206 2RZ REAR MOTOR BEARING 6206 2RZ FLAT WASHER 10MM CAP SCREW M10-1.5 X 35 C12.9 MOTOR GASKET DRAIN PLUG 3/8" NPT HEX HEAD CAP SCREW M8-1.
Spindle Feed Breakdown 203 204 201 202 205 206 210 207 208 212 213 214 224 209 225 215 226 216 227 217 218 219 220 221 222 223 228 230 231 229 232 233 Model G0756 (Mfg.
Spindle Feed Parts List REF PART # DESCRIPTION REF PART # DESCRIPTION 201 202 203 204 205 206 207 208 209 210 212 213 214 215 216 217 PHLP HD SCR M6-1 X 12 PLATE ROLL PIN 6 X 5 COILED SPRING GEAR SHAFT WOODRUFF KEY 8 X 5 WOODRUFF KEY 8 X 5 EXT RETAINING RING 5MM WORM GEAR ELECTROMAGNETIC TOOTH CLUTCH ARMATURE CAP SCREW M4-.
Headstock Breakdown 314 309 308307 306 312 310 313 305 304 311 318 303 302 301 319 320 321 315 316 317 382 322 323 324 325 331 326 327 328 329 340 333 334 335 330 332 336 337 Model G0756 (Mfg.
Headstock Breakdown 2 344 353 352 351 343 350 348 349 347 345 367 346 366 355 365 354 364 363 362 360 356 358 357 361 376 359 375 373 374 372 368 369 370 371 381 380 377 378 -54- 379 Model G0756 (Mfg.
Headstock Parts List REF PART # DESCRIPTION REF PART # DESCRIPTION 301 302 303 304 305 306 307 308 309 310 311 312 313 314 315 316 317 318 319 320 321 322 323 324 325 326 327 328 329 330 331 332 333 334 335 336 337 338 339 340 341 342 HEADSTOCK HOUSING AUTO DOWNFEED SHIFTING FORK DOWEL PIN 10 X 20MM AUTO DOWNFEED SHIFTING SHAFT AUTO DOWNFEED INDICATOR HUB SET SCREW M8-1.25 X 25 PILOT AUTOMATIC DOWNFEED DIAL STEEL BALL 6MM COMPRESSION SPRING 0.8 X 5 X 16 SET SCREW M8-1.
Electrical Parts Breakdown Electrical Panel 402 405 403 404 406 401 425 407 408 409 424 431 430 423 428 429 426 427 Control Panel 410 C2SS2-10B-10 411 4 2 2 414 1 3 5 7 9 11 13 15 1 420 Work Lamp LX5W-A11N 419 8 6 12 10 16 14 C2SS2-10B-10 412 -56- 4 421 x1 3 432 C2SS2-10B-10 C2SS2-10B-10 x2 417 CP1-10R-01 413 422 419 LX5W-A11N 418 418-1 Model G0756 (Mfg.
Electrical Parts List REF PART # DESCRIPTION REF PART # DESCRIPTION 401 402 403 404 405 406 407 408 409 410 411 412 413 414 417 418 ROTARY SWITCH CANSEN LW26GS-20 4P CIRCUIT BREAKER HUILONG DZ451-63 D10 3P CIRCUIT BREAKER HUILONG DZ451-63 D1 2P CIRCUIT BREAKER HUILONG DZ451-63 C3 1P CIRCUIT BREAKER HUILONG DZ451-63 C1 1P CIRCUIT BREAKER HUILONG DZ451-63 C1 1P CONTACTOR TIANSHUI GSC-1201 24V CONTACTOR TIANSHUI GSC-1201 24V CONTACTOR TIANSHUI JZC3-40D 24V SELECTOR SWITCH ABB C2SS2-10B-10 SELECTOR SWITCH
Labels & Cosmetics 502 503 506 501 509 508 507 510 511 504 509 505 512 509 513 REF PART # DESCRIPTION REF PART # DESCRIPTION 501 502 503 504 505 506 507 GLASSES FACE SHIELD LABEL 2"W X 3.3"H ENTANGLEMENT LABEL 2"W X 3.3"H READ MANUAL LABEL 2"W X 3.3"H DISCONNECT POWER LABEL 2"W X 3.3"H COOLANT HAZARD LABEL 2"W X 3.3"H GEARBOX SPEEDS LABEL CONTROL PANEL LABEL 508 509 510 511 512 513 MODEL NUMBER LABEL ELECTRICITY LABEL 1.4"W X 1.
WARRANTY CARD Name _____________________________________________________________________________ Street _____________________________________________________________________________ City _______________________ State _________________________ Zip _____________________ Phone # ____________________ Email _________________________________________________ Model # ____________________ Order # _______________________ Serial # __________________ The following information is given on a voluntary basis.
FOLD ALONG DOTTED LINE Place Stamp Here GRIZZLY INDUSTRIAL, INC. P.O.
WARRANTY & RETURNS Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance.
