MODEL T23107 CHAIN SAW SHARPENER OWNER'S Manual
This manual provides critical safety instructions on the proper setup, operation, maintenance, and service of this machine/tool. Save this document, refer to it often, and use it to instruct other operators. Failure to read, understand and follow the instructions in this manual may result in fire or serious personal injury—including amputation, electrocution, or death. The owner of this machine/tool is solely responsible for its safe use.
Specifications Motor 120V,60Hz Rpm’s Vise Capacity Table/Vise Angles Arbor Diameter 4200 0.80"to 0.50" 35 Degrees Right to Left 7/8" Wheel Dimensions 4-1/4"Dia. X 1/8" Thick Overall Dimensions 9"W x 10"L x 12-1/8"H Weight 4.85Lbs Save This manual You will need the manual for the safety warnings and precautions, assembly instructions, operating and maintenance procedures, parts list and diagram. Keep the manual in a safe and dry place for future reference.
9.Maintain tools with care. Keep tools sharp and clean for better and safer performance. Follow instructions for lubricating and changing accessories. Inspect tool cords periodically and if damaged, have them repaired by an authorized technician. The handles must be kept clean, dry, and free from oil and grease at all times. 10. Avoid unintentional starting. Be sure the switch is in the Off position when not in use and before plugging in. 11.Stay alert. Watch what you are doing, use common sense.
Additional Safety Warnings Grinding Wheel Warnings 1.Do not use a grinding wheel if it is chipped, cracked, or worn. You can check if the wheel has cracks not visible to the human eye by hanging it up by the central hole and tapping it with a non-metal object (ie: screwdriver handle). If it is in good condition it will produce a metallic sound. A dull sound indicates a crack or break. 2.Only use grinding wheels that fit the arbor (7/8").
Page 4 Warning ! Always unplug the unit before changing grinding wheels, or when making any adjustments to the sharpener. Mounting a Grinding Wheel Refer to the assembly drawing on page 10 and FIGURE 3 and FIGURE 4 below. 1. 2. 3. 4. Raise the Top Housing (#4) and lock it in the up position by tightening the Lock Stop (# 6) Remove the two screws holding the Grinding Wheel Cover (#11), Set the cover aside. Unscrew the Grinder Lock Cap (#9) that holds the Grinding Wheel ( #8) in place.
Operation Warning ! Always unplug the unit while adjusting chain to be sharpened. Refer to the assembly drawing on page 10 and the various photographs. Note: Raise the Top Housing (#4) while adjusting the chain. 1.Clean the chain before sharpening . Wash it with o non-flammable solvent. Don’t not use Gasoline. Dry the chain. Page 5 Operation (continued) 2.Lift up the Chain Stop(#23) and secure the chain in the sliding Guides (#31). See FIGURE 6. 3.
4.See FIGURES 5&6. Loosen the LOCK Wheel (#18) to allow entire housing to turn. Rotate the housing to match the degree of angle you need on the Angle Gauge. Chains come in various sizes with varying degrees of sharpening angles. Check with your chain manufacturer’s manual to determine what degree you need to sharpen at. Once the degree is set, tighten the Lock Wheel(#18). 5.Lower the Top Housing(#4) so that the Grinding Wheel(#8) skims the chain tooth. 6.
8.Lock the chain in the Sliding Guides (#31)by turning the Handle(#34). See FIGURE 8.The Handle(#34) should be situated so that you can easily release and tighten it . You will need to release it each time you move to the next link, and tighten it to sharpen each link. 9.If the chain has been repeatedly sharpened, the chain depth limiting gauges may need to be taken down with a flat file(not included). See FIGURES 8&9 .File down each gauge so that they are at a lower level than cutting teeth. Sharpening.
5.After you fininshed sharpening all of the teeth set for your current angle, turn off the machine by pushing the red button on the Switch Plate(#5) and unplug the unit. 6.Loosen the Lock Wheel(#18)and reset the angle so that the first tooth that hasn’t been sharpened is positioned against the Chain Stop (#23) and locked in as explained on page 6. See FIGURE 11. 7.
Parts List Parts No. 1 2 3 4 5 6 7 Description Screw Motor Cover Power Cord Top Housing Switch Plate Lock Stop Grinding Wheel Base Qty. 3 1 1 1 1 1 1 Parts No.
WARRANTY AND RETURNS Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance.
Buy Direct and Save with Grizzly ® – Trusted, Proven and a Great Value! ~Since 1983~ Buy Direct and Save with Grizzly ® – Trusted, Proven and a Great Value! Visit Our Website Today For ~Since 1983~ Current Specials! Visit Our Website Today For Current Specials! ORDER 24 HOURS A DAY! 1-800-523-4777 ORDER 24 HOURS A DAY! 1-800-523-4777
