OPERATOR’S MANUAL AND PARTS LIST MODEL GRTSM200 STAPLER Tough as nails Distributed By www.grip-rite.
TABLE OF CONTENTS SPECIFICATIONS SPECIFICATIONS TABLE OF CONTENTS -------------------------------- 2 SPECIFICATIONS --------------------------------------- 3 Fastener Selection Chart ------------------------ 3 SAFETY ---------------------------------------------------- 4 TOOL PARTS --------------------------------------------- 8 PART DESCRIPTIONS --------------------------------- 9 OPERATION --------------------------------------------- 10 Loading Staples ---------------------------------- 10 Adjusting Fa
SAFETY SAFETY SAFETY LABELS SAFETY INSTRUCTIONS This pneumatic fastening tool includes a warning label to help remind you of important safety information when operating the tool. The safety label must be legible at all times, and must be replaced if it becomes worn or damaged. WEAR SAFETY GLASSES Always wear safety glasses with side shields that meet ANSI Z87.1 requirements when operating the tool. Make sure all others in work area wear safety glasses.
SAFETY SAFETY SAFETY INSTRUCTIONS SAFETY INSTRUCTIONS DO NOT ATTEMPT TO OPERATE THE TOOL IF THE TOOL’S OPERATING CONTROLS HAVE BEEN MODIFIED OR ARE NOT WORKING PROPERLY. Attempting to use a tool with modified or malfunctioning trigger or workpiece contact can result in a fastener being driven unintentionally. USE CORRECT FASTENERS Only use the correct fastener for the tool. Using fasteners with incorrect specifications can jam the tool or cause serious injuries.
DESCRIPTION DESCRIPTION TOOL PARTS PART DESCRIPTIONS 1 1. 360° Adjustable Air Deflector - Tool-free adjustment blows exhaust air away from operator. 12 locking positions for secure settings. 2 2. Cushioned Grip - Cushioned handgrip reduces fatigue and provides comfortable operation. 3. Dual Action Trigger (Standard) - Actuates tool when workpiece contact is depressed against work surface. Permits contact-trip (bump fire) or trigger-fire operation.
OPERATION OPERATION LOADING FASTENERS ADJUSTING STAPLE DRIVE LOADING INSTRUCTIONS 1. Disconnect tool from air supply using quick-connect coupling. DANGER A fastener can be driven unintentionally if the trigger and safety bracket are activated at the same time. Always disconnect tool from air supply before loading fasteners, making adjustments, or performing any service on tool. Keep finger off trigger until ready to drive a fastener. 1. Pull pusher (A) back to latched position at rear of magazine. 3.
OPERATION MAINTENANCE TOOL OPERATION MAINTENANCE CONTACT TRIP (BUMP FIRE) DRIVING METHOD (Standard) Your tool will last longer and perform better if periodic maintenance is performed. Please use the information below to keep your tool operating in top condition. 1. Position the nose of the tool over the work surface, near the area where the first fastener is to be driven. 2. Squeeze and hold the trigger in the depressed position. 3.
PARTS SCHEMATIC PARTS LIST ITEM P/N 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16A 17 18 19 20 21 22 23A 24 25 26 27 28 29 30 31 32 33 34 35 36 37A 38 39 40 A B C D 14 GRTN3360 GRTN3220 GRTN3230 GRTN1990 GRTN3740 GRTN3750 GRTN710 GRTN3350 GRTN2300 GRTN570 GRTN3240 GRTN2310 GRTN2320 GRTN610 GRTN2360 GRTN3760 GRTN600 GRTN2200 GRTN3250 GRTN620 GRTN3770 GRTN550 GRTN3780 GRTN2290 GRTN3790 GRTN2220 GRTN2240 GRTN630 GRTN2100 GRTN2130 GRTN2170 GRTN640 GRTN830 GRTN2230 GRTN810 GRTN820 GRTN650 GRTN2540 GRTN2210 GRTN790
TROUBLESHOOTING TROUBLESHOOTING TOOL TROUBLESHOOTING FASTENER DRIVING PROBLEMS Your pneumatic fastening tool has been designed for long life and troublefree operation. However, if operating problems arise, please use the troubleshooting information below to determine how to remedy the problem. DANGER Always disconnect tool from air supply before performing any service on tool. Correcting a problem while the tool is pressurized may result in injury from fastener discharge or tool operation.
WARRANTY WARRANTY PNEUMATIC TOOL/COMPRESSOR WARRANTY Pneumatic nailers, staplers & compressors marketed under the GRIP RITETM brand are warranted to be free from defects in workmanship & materials (except rubber o-rings, bumpers, seals, driver blades, dipsticks, & air filters) for a period of one year from the date of original purchase.
USE GENUINE GRIP-RITE® FASTENERS FOR BEST PERFORMANCE www.grip-rite.
