IN-WALL OUTLET Installation Instructions
WARNING This product requires handling of high voltage wiring. Please turn off your circuit breaker and follow instructions carefully. Turn off your circuit breakers and follow safety precautions in order to avoid fire, personal injury, or death.
WHAT’S IN THE BOX? ConnectSense In-Wall Outlet (20 amp pictured) 2 mounting screws
WHAT YOU’LL NEED Phillips head #2 screwdriver Flat head screwdriver Wall plate Pliers (optional)
COMPATIBILITY Is your circuit a 15amp or 20amp? 15 amp circuit supports ONLY 15 amp In-Wall Outlet. 20 amp circuit supports both 15 amp and 20 amp In-Wall Outlet. RATING Cat. No. Electrical Rating for ANSI/NEMA Integral Switching Means Config and Electrical Rating Tungsten, A LED & CFL, A Motor Receptacle with integral switching means CS-IWO-15 5-15 R 15A, 125 V 1000 (8.3) 3.75 1/2 HP motor CS-IWO-20 5-20 R 20A, 125 V 1500 (12.5) 5.
TURN OFF YOUR BREAKERS Turn off the circuit breaker for the outlet you are replacing. If breakers aren’t labeled, turn off master breaker. Before proceeding - Check for power by plugging in a device to confirm breakers are off.
REMOVE OLD OUTLET Unscrew wall plate and outlet from wall. Carefully disconnect wires attached to outlet. Remove your existing outlet. Before removing - Be sure the device is not powered.
IDENTIFY & STRIP WIRES You should see 3 types of wires in your wall: Line (Black) Neutral (White) Ground (Green) Be sure your wires have a ½ inch stripped at the end of each wire. Use a proper* screwdriver to tighten the terminal screws. *Screwdriver should have a torque value of 14lbf-in (16.
Neutral Wire Line Wire Ground Wire
CONNECT IN-WALL OUTLET Line Wire (Black) Neutral Wire (White) Ground Wire (Green) To connect another device on the same circuit, use the two middle inputs. Be sure that the line and neutral are installed into the correct input location.
MOUNT IN-WALL OUTLET Use the mounting screws provided to mount your ConnectSense In-Wall Outlet.
POWER ON SYSTEM Return to circuit breaker and turn on power.
TEST YOUR IN-WALL OUTLET Test the outlet by double tapping the icons. LED indicates a tap has been received.
INSTALLATION COMPLETE! Download the ConnectSense app to register your device, connect to Wi-Fi, and begin enjoying the smart features of the device. To connect to HomeKit, use the Home app or ConnectSense app on your iOS device. A backup code is available on the last page of this manual.
YOUR IN-WALL OUTLET
Setup Indicator Blinking Red - Connection failed, try reset Blinking Yellow – Waiting to connect to a Wi-Fi network Blinking Green – Connected Off – Setup is Complete Capacitive Touch Indicator Blink – Touch detected Plug A – Double tap On/Off NFC Pairing – Touch mobile device in this area during setup Reset Reboot - Three taps + hold for 5 seconds (Setup indicator turns solid blue) WiFi Reset - Three taps + hold for 10 seconds (Setup indicator turns solid yellow) Factory Reset - Three taps + hold for
LED COLOR CODES SETUP INDICATOR LED State Description Yellow - Slow blink Device ready to add to Wi-Fi Network Yellow - On Reboot device to add to Wi-Fi Network Yellow - Fast blink Device connecting to Wi-Fi Network Green - Slow Blink Connected to your Wi-Fi Network & Finishing Setup Green - On, then off Setup Complete Red - Fast blink Can’t connect to Wi-Fi Network, Reset Red - Slow blink Setup process failed, Reset Blue - Slow flash Identify device
CAPACITIVE TOUCH INDICATOR LED State Description Blue - Blink Touch On Double tap power button, when off Blink per button press Off Double tap power button, when on Blink per button press Reboot Three taps + hold for 5 seconds Setup indicator turns solid blue Wifi Reset Three taps + hold for 10 seconds Setup indicator turns solid yellow Factory Reset Three taps + hold for 15 seconds Setup indicator turns solid red
TROUBLESHOOTING To reset your In-Wall Outlet, tap the Reset button 3 times and hold for 15 seconds or insert a plug and unplug it 5 times into Plug B. For commonly asked questions about the In-Wall Outlet, visit ConnectSense.com/IWOFAQ For instructions to connect to Amazon Alexa, visit ConnectSense.com/IWOAlexa For instructions to connect to Google Assistant, visit ConnectSense.com/IWOGA We are here to help! ConnectSense.com support@connectsense.
LEGAL FCC/IC Information: This device complies with Part 15 of the FCC Rules and with Industry Canada license exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
IN-WALL OUTLET HomeKit Code
