TRIPLE BUNKBED Color: Mocha Customer satisfaction is important to us. For faster service, always have the model number ready when calling our toll free number or emailing us. ATTENTION USE THIS MANUAL TO ASSEMBLE THE TRIPLE BUNK BED Date of Purchase: _____ / _____ / _____ Lot Number: (taken from carton) DO NOT RETURN PRODUCT TO THE STORE. If a part is missing or damaged, contact our customer service department. We will replace the part FREE of charge.
CUSTOMER SERVICE If you are missing parts or have any questions about this product, contact our customer service representative first! You can also order parts by writing to the address listed below. Please include the product model number, color and a detailed description of the part. WARNING * STRANGULATION HAZARD - NEVER ATTACH OR HANG ITEMS TO ANY PART BUNK BED THAT ARE NOT DESIGNED FOR USE WITH THE BED; FOR EXAMPLE, BUT NOT LIMITED TO HOOKS, BELTS AND JUMP ROPES.
NOTES * READ EACH STEP CAREFULLY BEFORE STARTING. IT IS VERY IMPORTANT THAT EACH STEP OF INSTRUCTION IS PERFORMED IN THE CORRECT ORDER. IF THESE STEPS ARE NOT FOLLOWED IN SEQUENCE, ASSEMBLY DIFFICULTIES WILL OCCUR AND CAN RESULT IN INJURY. * CAUTION: ADULT ASSEMBLY REQUIRED * MAKE SURE ALL PARTS ARE INCLUDED. WORK IN SPACIOUS AREA, PREFERABLY ON A SMOOTH SOFT SURFACE. * ASSEMBLY WILL REQUIRE TWO PEOPLE. * MOST BOARD PARTS ARE LABELED OR STAMPED ON THE RAW EDGE.
TRIPLE BUNK BED HARDWARE LIST 1 2 Φ 1/4" x 100mm Φ 6.5mm x 48mm JOINT CONNECTOR (4mm HEX HEAD) 24 PCS WOOD JOINT CONNECTOR (4mm HEX HEAD) 28 PCS 3 4 Φ 6.5mm x 100mm Φ 4mm x 35mm WOOD JOINT CONNECTOR (4mm HEX HEAD) 40 PCS FLAT HEAD SCREW 36 PCS 5 6 Φ 10mm x 100mm Φ 4mm x 30mm METAL DOWEL 8 PCS FLAT HEAD SCREW 9 PCS 7 8 Φ 10mm x 50mm WOOD DOWEL 106 PCS 9 ALLEN KEY 1 PC 10 11 Φ 11.
TRIPLE BUNK BED PARTS LIST A B TOP POST 1 PC D C TOP POST 2 PCS E BOTTOM POST 2 PCS TOP POST 1 PC F BOTTOM POST 2 PCS HEADBOARD TOP CROSS 6 PCS NOTE- the components needed to assemble the triple bunk bed are packed in 2 boxes. Make sure that all parts are accounted for before beginning assembly.
TRIPLE BUNK BED PARTS LIST G H HEADBOARD BOTTOM CROSS 6 PCS J I TOP FRONT SIDE RAIL 1 PC K BACK SIDE RAIL 2 PCS M L BOTTOM BACK SIDE RAIL 1 PC N LONG GUARDRAIL 4 PCS P SHORT GUARDRAIL 2 PCS RIGHT LADDER END 1 PC HEADBOARD CENTER CROSS 6 PCS SLAT WITHOUT WOOD DOWEL 18 PCS O Q S BOTTOM FRONT SIDE RAIL 1 PC LEFT LADDER END 1 PC R LADDER STEP 9 PCS T GUARDRAIL LEG 3 PCS U SLAT WITH WOOD DOWEL 6 PCS GUARDRAIL POST 2 PCS
TRIPLE BUNK BED PARTS LIST V W RIGHT GUARDRAIL POST 1 PC Y X CENTER POST 1 PC Z CENTER POST 1 PC B1 A1 CENTER POST 1 PC C1 SHORT GUARDRAIL 2 PCS CENTER POST 1 PC FRONT SIDE RAIL 1 PC D1 LONG LADDER LEFT END 1 PC LONG LADDER RIGHT END 1 PC
TRIPLE BUNK BED 7 7 7 7 7 7 7 7 7 7 7 7 7 7 A 7 7 C STEP 1 3 Insert wood dowels (7) into the ends of headboard top cross (F), headboard bottom cross (G) and headboard center cross (S). Attach them to top posts (A & B) using wood joint connectors (3) as shown. Tighten the wood joint connectors (3) with the Allen key (8).
TRIPLE BUNK BED 7 E 7 7 7 7 E 7 7 7 D 7 7 7 7 7 7 D 7 7 STEP 2 3 Insert wood dowels (7) into the ends of headboard top cross (F), headboard bottom cross (G) and headboard center cross (S) and attach them to bottom posts (D) & (E) using wood joint connectors (3) as shown. Tighten the wood joint connectors (3) with the Allen key (8).
TRIPLE BUNK BED K I STEP 3 Attach the two headboards with bottom posts (D & E) to bottom front side rail (I) and bottom back side rail (K) using joint connectors (1) and barrel nuts (9) as shown. Tighten the joint connectors (1) with the Allen key (8). Note: This is the lower bunk.
TRIPLE BUNK BED J H STEP 4 Insert wood dowels (7) into each end of the long guardrails (M). Attach two long guardrails (M) and two top side rails (H & J) to top posts (A & B) and (C & B) as shown. Fasten top side rails (H & J) with joint connectors (1) and barrel nuts (9). Fasten long guardrails (M) with wood joint connectors (3). Tighten the joint connectors (1) and wood joint connectors (3) with the Allen key (8). Note: This is the top bunk.
TRIPLE BUNK BED U 8 3 U 7 11 10 A 10 N H B STEP 5 Insert wood dowels (7) into short guardrails (N). Attach short guardrails (N) to guardrail post (U) with wood joint connectors (3) as shown. Fasten the short guardrails (N) to top post (B) with wood joint connectors (3). Fasten the guardrail post (U) to top front side rail (H) with joint connectors (10) and hex cap (11) as shown.
TRIPLE BUNK BED M 6 N 6 6 H 6 STEP 6 Attach the guardrail leg (R) to the short guardrails (N) and top front side rail (H) with flat head screws (6). Attach the other guardrail leg (R) (on the other side of the bed) to long guardrails (M) and top back side rail (J) with flat head screws (6) as shown. Use a Phillips head screwdriver (not included) to tighten the flat head screws.
TRIPLE BUNK BED O P STEP 7 Insert wood dowels (7) into the end of the ladder steps (Q). Attach left ladder end (O) and right ladder end (P) to ladder steps (Q) with wood joint connectors (2). Tighten the wood joint connectors (2) with the Allen key (8).
TRIPLE BUNK BED 7 7 7 7 7 7 7 7 7 7 7 7 7 7 W 7 7 Z 3 STEP 8 Insert wood dowels (7) into the ends of headboard top cross (F), headboard bottom cross (G) and headboard center cross (S). Attach the center posts (W & X) using wood joint connectors (3) and Allen key (8). NOTES: Headboard top crosses (F, G and S) may require that they be pulled closer together or further apart in order to allow wood dowels (7) to align with holes in center posts (W & X).
TRIPLE BUNK BED J STEP 9 Insert wood dowels (7) into each end of the long guardrails (M). Attach two long guardrails (M) and side rails (A1 and J) to center posts (W & X) and (Y & Z) as shown. Fasten side rails (A1 and J) with joint connectors (1) and barrel nuts (9). Fasten long guardrails (M) with wood joint connectors (3). Tighten the joint connectors (1) and wood joint connectors (3) with the Allen key (8). Note: this is the middle bunk.
TRIPLE BUNK BED 11 10 V 11 10 10 STEP 10 Insert wood dowel (7) into short guardrails (B1). Attach short guardrails (B1) to guardrail post(U) and right guardrail post (V) with wood joint connectors (3) as shown. Fasten the guardrail post (U) and right guardrail post (V) to center front side rail (A1) with joint connectors (10) and hex cap (11) as shown.
TRIPLE BUNK BED 6 6 6 6 STEP 11 Attach the guardrail leg (R) to long guardrails (M) and side rail (J) with flat head screws (6) as shown. Use a Phillips head screwdriver (not included) to tighten the flat head screws.
TRIPLE BUNK BED STEP 12 To assemble the ladder, insert wood dowels (7) into the end of the ladder steps (Q). Attach the long ladder ends (C1 & D1) to ladder steps (Q) with wood joint connectors (2) and Allen key (8).
TRIPLE BUNK BED 5 5 D 5 D I 5 E STEP 13 Place four metal dowels (5) into the holes in the bottom posts (D and E). Stack the middle bunk on the bottom bunk with the help of another person.
TRIPLE BUNK BED B 5 A 5 H C 5 B 5 I STEP 14 Place four metal dowels (5) into the holes in the center posts (W, X, Y, Z). Stack the top bunk on the middle bunk with the help of another person.
TRIPLE BUNK BED A U 2 A U H 2 H 2 2 2 2 I I 2 2 8 back view STEP 15 Attach the long ladder to front side rails (H & A1 & I) with wood joint connectors (2) as shown. Use Allen key (8) to tighten the joint connectors.
TRIPLE BUNK BED V 2 I V 2 2 O P P O I 2 8 STEP 16 2 back view Attach the short ladder to the front side rail (A1 & I) with wood joint connectors (2) as shown. Use Allen key (8) to tighten the joint connectors.
TRIPLE BUNK BED J L L H L T J T L L L L L K T T I 4 STEP 17 Insert two slats with wood dowel (T) into the center slots of the top side rails (H &J) of the upper bunk as shown. Attach slats without wood dowel (L) onto top side rails (H &J) of the upper bunk with flat head screws (4) as shown. Use Phillips screwdriver (not included) to tighten flat head screws (4). Repeat this process for the middle and bottom bunk.
TRIPLE BUNK BED To convert the bunk bed into three different twin bed, remove both ladders and all the guardrails. With the help of another person, unstack the top bunk and center bunk from the lower bunk.
TRIPLE BUNK BED CAUTION: This unit is intended for use only with the products and/or maximum weights indicated. Use with other products and/or products heavier than the maximum weights indicated may result in instability or cause possible injury. DO NOT ALLOW HORSEPLAY ON OR UNDER THE BED AND PROHIBIT JUMPING ON THE BED. DO NOT ALLOW CHILDREN UNDER 6 YEARS OF AGE TO USE THE UPPER BUNK. BED IS DESIGNED FOR CHILDREN RANGING FROM 6 YEARS OF AGE TO YOUNG TEENAGERS.
Customer Service PLEASE DO NOT RETURN THIS PRODUCT TO THE STORE PLEASE CONTACT CUSTOMER SERVICE REPRESENTATIVES AT THE FOLLOWING NUMBERS SHOULD THERE BE ANY MISSING OR DEFECTIVE PART(S).
