E40.0.01.6C-02 Data logger for from Version V1.5 Operating Manual humidity temperature air pressure EASYLO OG 80 CL GRE EISINGER electronic Gm mbH D - 931 28 Regenstauf, Hans-Sachs-Stra aße 26 phone.: +49 9 9402 / 9383-0, fax: +49 9402 / 9383-33, eMail: info@greiisinger.
E40.0.01.6C-02 Operating Manual EASYLOG 80 CL Page 2 of 12 Content 1. 2. 3. 4. 5. 6. General description .................................................................................................... 2 Required accessory ................................................................................................... 2 Safety advice ............................................................................................................. 3 Notes on the logger’s delivery status ...............
E40.0.01.6C-02 Operating Manual EASYLOG 80 CL Page 3 of 12 3. Safety advice This device has been designed, assembled and tested in accordance with the safety regulations for electronic measuring device. However, its trouble-free operation and reliability cannot be guaranteed unless the standard safety measures and special safety advices regarding the device will be adhered to when using the device. 1.
E40.0.01.6C-02 Operating Manual EASYLOG 80 CL Page 4 of 12 5. EASYBus connecto or Assignment of panel jack (view on pins) EASY YBus connection not connected c 6. Display and contro ol elements 6.1 Display Main display Logg: indicates tha at logger is recording BAT: signals weakk battery (see chapterr 9).
E40.0.01.6C-02 Operating Manual EASYLOG 80 CL Page 5 of 12 7. Operation 7.1 Operating possibilities at the device - display selection Function Procedure Push button Switch display shortly 2 for about 5 seconds. 3 shortly The min-values of the measuring channel are displayed for 4 seconds. (The min-value display function is signalled by the display element “MIN“). Note: You can immediately switch to the next measuring channel pushing the button again.
E40.0.01.6C-02 Operating Manual EASYLOG 80 CL Page 6 of 12 7.2 Operating possibilities at the device - logger operation Function Procedure Push button Display and adjust cycle time SET 1 and 2 at the same time. The main display shows “CYCL”. The secondary display shows the currently adjusted cycle time [in sec.]. If the logger is currently not recording, the desired cycle time [4 sec to 5h (18000 sec)] can be adjusted via the buttons and .
E40.0.01.6C-02 Operating Manual EASYLOG 80 CL Page 7 of 12 7.3 Operating possibilities via software GSOFT 40K You can easily operate the logger via the software GSOFT 40K (> V7.14). This software provides a variety of functions to operate the logger.
E40.0.01.6C-02 Operating Manual EASYLOG 80 CL Page 8 of 12 9. Operating displays The EASYLOG provides two LCD-displays: 7 mm (main display) and 5.8 mm (secondary display). 9.1 Measured value display The LCD mainly displays the measured values: a) % °C AL Logg b) °C hPa SL Logg MEASURED VALUE DISPLAY Alternating display of the following measuring channels: a) main display: sec.
E40.0.01.6C-02 Operating Manual EASYLOG 80 CL Page 9 of 12 9.3 System messages ... BATTERY: % °C • display of the BAT-arrow left hand down: The EASYLOG battery is almost spent and needs to be replaced. The data recording is still active. • permanent display BAT: The battery is spent and the recording has been automatically stopped (even if at EASYBus-operation). It is still partly possible to read the measured values and to read-out the saved logger data.
E40.0.01.6C-02 10. % °C MAX DIF MIN °C hPa SET 1 2 Operating Manual EASYLOG 80 CL Page 10 of 12 Specifications Measuring range: 3 Temperature -25.0 … +60.0 °C Humidity 0.0 … 100.0 %RH (recommended range : 10 … 90 %RH) Air pressure 300.0 … 1100.0 hPa (mbar) Additional selectable variables Wet-bulb temperature -27.0 … +60.0 °C Dew point temperature -40.0 … +60.0 °C Enthalpy -25.0 … 999.9 kJ/kg Moisture content of the air 0.0 … 640.0 g/kg Resolution 0.1 °C / 0.1 %RH / 0.
E40.0.01.6C-02 % °C MAX DIF MIN °C hPa SET 1 2 Operating Manual EASYLOG 80 CL Page 11 of 12 Recording period depending on the chosen measuring cycle i. e. 521 days at 3 min measuring cycle 7.1 years at 15 min measuring cycle Alarm function alarm points selectable within the measuring range and alarm delay adjustable from 0 to 500 min Nominal temperature 25 °C Operating temperature -25.0 … +60.0 °C Storage temperature -30.0 … +70.0 °C 3 Housing Dimensions 48.5 × 48.5 × 35.
E40.0.01.6C-02 Operating Manual EASYLOG 80 CL Page 12 of 12 12. Frequently asked questions [FAQ] Problem: Possible reason: Remedy: Problem: Possible reason: Remedy: Problem: Possible reason: Remedy: Problem: Possible reason: Remedy: The logger cannot be stopped via keys. “Logger stop via buttons disabled” has been activated at the configuration of the logger. Deactivate this function by means of GSOFT 40K (at tab „settings“). The logger cannot be stopped both via keys and GSOFT 40K.
