Owner’s Manual Introduction Features / Benefits Records Specifications Warnings Controls / Diagrams Setting Up the Unit Operating the Unit Maintaining the Unit Safety & Warnings Consumer Information Warranty Information www.GreenTechEnv.
Introduction Welcome to a more comfortable, efficient way of heating your living spaces during cold weather! pureHeat+ is the most complete and advanced space heating system on the market. It heats using a cuttingedge PTC (Positive Thermal Coefficient) element that heats the air efficiently without drying it out. It purifies your air with PCO technology that features a high power germicidal UVC bulb.
Specifications Voltage:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120V ~60Hz Power:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . up to 1500 watts Heat Output:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5200BTU Remote Battery: . .
Control Panel & Remote Control Diagrams LCD Display Diagram 5
Unit Front Diagram Unit Rear Diagram 6 Copyright © 2010 GreenTech Environmental; All Rights Reserved
Setting Up the Unit 1. Unpack the unit by cutting open taped areas. Fold back box flaps and gently turn entire box upside down. Lift box off of styrofoam packed contents. Remove styrofoam, turn upright. We recommend keeping packing materials for future transport or storage of unit. 2. Find a level and unobstructed location to place heater away from cold walls (outside walls). 3. Plug the POWER CORD into a grounded outlet (120V, 15A or higher). 4.
Quiet Function • If you feel the unit is too loud for your environment, such as when you are sleeping, press the QUIET MODE CONTROL button. The unit continues to heat, humidify, and purify according to active modes, but the fan runs on the most silent speed. Standby Mode • When the room exceeds set temperature by 2 Degrees F the heater goes into “STANDBY MODE”, essentially turning off except the temperature sensor.
Cleaning the Unit 1. Unplug the POWER CORD from the outlet. 2. Carefully wipe the exterior of the unit with a soft, damp (not wet) cloth and dry thoroughly with a soft, dry cloth. Do not use harsh or abrasive cleaners as these may damage the aesthetic finish of the unit. 3. Remove particulate that may have gathered in the HOT AIR OUTLET or HUMIDIFIER OUTLET using a vacuum with a brush attachment. Replacing the PCO Cell After some time the “Replace UV BULB” indicator may appear on your LCD SCREEN.
Safety Info & Warnings 1. Do not operate the heater if any cord or part of the machine is damaged or has malfunctioned. Return heater for examination and repair if damage has occured. 2. Do not plug heater into anything other than a 3-prong 110v 15amp or higher grounded circuit receptacle. 3. Do not use an extension cord to power this heater. 4. Do not block the front grill or rear filter of the heater. Be sure that there is adequate space around the heater for air flow. 5.
Consumer Information GreenTech Environmental declines responsibility for all damages arising from improper use of the unit or in case of tampering with the unit. Warranty Information LIMITED WARRANTY INFORMATION Your pureHeat+ (Product) is warranted to be free from all defects in material and workmanship in normal household use for a period of (3) Years from date of purchase. The warranty is granted only to the original purchaser.
www.GreenTechEnv.
