INSTRUCTION MANUAL HK06FT Hydraulic Crimping Tool Read and understand all of the instructions and safety information in this manual before operating or servicing this tool. Register this product at www.greenlee.com 99930927 © 2011 Greenlee Textron Inc.
HK06FT Hydraulic Crimping Tool Table of Contents Description Description..................................................................... 2 Safety............................................................................. 2 Purpose of this Manual.................................................. 2 Important Safety Information......................................3–4 Identification................................................................... 5 Specifications.....................................
HK06FT Hydraulic Crimping Tool IMPORTANT SAFETY INFORMATION SAFETY ALERT SYMBOL Electric shock hazard: This tool is not insulated. When using this unit on or near energized electrical lines, use proper personal protective equipment. Failure to observe this warning could result in severe injury or death. This symbol is used to call your attention to hazards or unsafe practices which could result in an injury or property damage. The signal word, defined below, indicates the severity of the hazard.
HK06FT Hydraulic Crimping Tool IMPORTANT SAFETY INFORMATION An incomplete crimp can cause a fire. Use proper connector and cable combinations. • Improper combinations can result in an incomplete crimp. • The handle load will drop suddenly to indicate a completed crimp. If the handle load does not drop suddenly, the crimp is not complete. Failure to observe these warnings could result in severe injury or death. • This tool is intended for two-handed operation.
HK06FT Hydraulic Crimping Tool Identification 4 1 5 3 6 HK06FT 2 4. Handle Release 5. Decal 6. Decal 1. Crimping Head 2. Flip Top 3. Release Lever Specifications Crimping Tool Length.............................................................................................535 mm (21.06") Width...................................................................................................191 mm (7.5") Height.........................................................................................
HK06FT Hydraulic Crimping Tool Operation 1. Follow the lug manufacturer’s instructions for appropriate cable strip length and surface preparation. 2. Insert cable fully into connector. 3. Pull the latch pin and open the latch. Insert the connector with cable into the crimping head. Close the latch and push the pin completely into the latch. Electric shock hazard: This tool is not insulated. When using this unit on or near energized electrical lines, use proper personal protective equipment.
HK06FT Hydraulic Crimping Tool Connector Selection Tool Range: Copper — 4 AWG to 750 kcmil (except as noted ∆) Aluminum — 6 AWG to 750 kcmil (except as noted q) This tool is cUL and UL classified for use with the following connector brands: CONNECTOR BARREL ANDERSON BLACKBURN® TYPE TYPE Copper Splices Copper Lugs Dual-rated Aluminum Splices Dual-rated Aluminum Lugs BURNDY ILSCO PANDUIT T&B PENNUNION Short VHSS CSP∆ YS-L∆ CT∆ SCSS/SCS∆ 54507–54523TB∆ BCU Long VHS CU∆ YS∆ CTL∆ SCL/SCH∆
HK06FT Hydraulic Crimping Tool 5 31 29 40 22 23 27 15 38 38 13 2 36 35 21 39 14 1 12 11 10 32 6 25 30 28 3 4 7 37 8 26 33 34 19 24 16 9 20 18 Illustration Greenlee / A Textron Company 8 4455 Boeing Dr.
HK06FT Hydraulic Crimping Tool Greenlee / A Textron Company 9 102 119 113 115 111 103 107 103 105 104 112 120 105 104 106 112 100 117 101 115 108 120 116 Illustration 4455 Boeing Dr.
HK06FT Hydraulic Crimping Tool 202 205 206 201 204 203 Illustration Greenlee / A Textron Company 10 4455 Boeing Dr.
HK06FT Hydraulic Crimping Tool Parts List Key Part No. Description Qty 1 50063847 Pump body................................................................................................ 1 2 50063456 Pump piston............................................................................................... 1 3 50063464 Sleeve........................................................................................................ 1 4 50063480 Ram............................................................
HK06FT Hydraulic Crimping Tool Parts List (cont’d) Key Part No. Description Qty 50017225 Quad point flip-top head assembly (includes 100–120) 100 50017276 Pin, spring.................................................................................................. 2 101 50017233 Cam yoke assembly................................................................................... 1 102 50061178 Latch........................................................................................................
