User's Guide

CE Regulations
by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or
more of the following measures:
This equipment complies with radio frequency (RF)
exposure limits adopted by the Federal Communications
Commission for an uncontrolled environment. This
equipment should be installed and operated with minimum
distance 24 cm between the radiator & your body.
FCC RF Exposure Compliance
■ Reorient or relocate the receiving antenna.
■ Increase the separation between the equipment and
receiver.
■ Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
■ Consult the dealer or an experienced radio/TV technician
for help.
Claim FCC Regulations
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference. and
(2) this device must accept any interference received,
including interference that may cause undesired operation.
■
This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to part 15
of the FCC Rules. These limits are designed to
provide reasonable protection against harmful
interference in a residential installation. This
equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions. may cause harmful
interference to radio communications. However, there
is no guarantee that interference will not occur in a
particular installation. if this equipment does cause harmful
interference to radio or t
elevision reception, which can
be determined
■
Changes or modifications not expressly approved by the
party responsible for compliance could void the user‘s
authority to operate the equipment
■
FCC Regulations
Warranty
Hardware warranty is for one year (12 months) from the date
of purchase. Customer’s unit and his accessories under
normal use for warranty period is free from error, improper or
inferior workmanship, material, and design.
This Warranty does not cover damage resulting from:
1. Defects and damages due to the equipment being used
other than its normal and customary manner.
2. An unauthorized disassembly, repair, alteration or
modifications being carried out, misuse, abuse,
negligence or accident howsoever caused.
3. Defects or damage arising from improper testing,
operation, maintenance, installation, or any alteration
or modification.
4. Use other than in accordance with the user manual,
rough handling, exposure to extreme thermal or
environmental conditions or a rapid change in such
conditions, corrosion, oxidation, unauthorized
modifications or connections, unauthorized opening or
repair, repair by use of unauthorized spare parts,
accidents, forces of nature, or other actions beyond the
reasonable control of GP.
9
10
11
12
8
13 14 15
This device meets the EU requirements and the
International Commission on Non-Ionizing Radiation
Protection ( ICNIRP ) on the limitation of exposure of the
general public to electromagnetic fields by way of health
protection. To comply with the RF exposure requirements,
this equipment must be operated in a minimum of 24 cm
separation distance to the user.
Hereby, Green Packet Berhad declares that the radio
equipment type OA series is in compliance with Directive
2014 / 53 / EU. The full text of the EU declaration of
conformity is available at the following internet address:
http://www.greenpacket.com/
23 dBm ± 2 dBm
Max. RF Power
RF Exposure Information
Simplified DoC
Use PC to Configure the ODU
After the ODU boots up properly, use the following
instructions to fine tune the direction of ODU to optimize
signal level and for any advanced personalized configuration.
A computer is required to execute the following steps.
The web-based configuration utility can be used for initial
device installation, parameter configuration, and function
management through the browser.
Ensure that the device is connected to the computer. Follow
these steps to log in to the web management page:
1. Open the browser, enter 192.168.0.1 in the address box,
and login Username and Password.
Access the Web Management Page
admin
admin
Default IP address: 192.168.0.1
Login
USERNAME
PASSWORD
2. Once logged in, an overview of current signal statistics will be
displayed, and you can have a status overview on device activity.
Note: You will automatically obtain the IP address and DNS server address.
SINR of 1OdB is the bare minimum to provide services.
During installation, the user must always try to get the best
SINR possible.
Note: SINR threshold varies per service plan. For more information,
contact service support.
Basic Troubleshooting
Q1: For No Internet
Ans: Check PoE LED if lit, check if black LAN cable is plug
to ODU.
Q2: LED (on the bottom side) does not light up
Ans: Make sure the ODU is correctly connected to PoE
injector - Connect RJ-45 port ( marked as Power+Data
Out) of PoE
injector to ODU's RJ-45 port by using Ethernet cable.
Q3: Unable to get access to the “Info Page"
Ans:
● Power supply (ODU to PoE injector and power adapter)
is correctly connected.
● Please enable the Laptop PC to automatically obtain IP
address.
● IP address is correct? Default IP address is
192.168.0.1
● Ensure PoE is Powered On.
● Ensure Cabling is Correct.
● Power Cycle PoE.
Note: Refer to Wi-Fi router manual to configure Wi-Fi, this is supplied
separately.