User's Guide

1 2 3
4 5 6
7
QUICK USER GUIDE
LTE CPE
OA-B48
About This Document
This document serves as a brief overview and setup guide
for OA series ODUs (Outdoor Units). The OA series is a LTE
outdoor unit. In this document, the terms ODU, Outdoor
CPE, and Outdoor Unit are used interchangeably.
Ensure that you have everything required to properly set up
your device.
Included Hardware
Version No. : V1.0
Release Time : 2020-12
Because of the product version upgrade or other reasons, the
content of the document will not be updated on a regular basis.
Unless otherwise agreed, this document is used only as a guide,
all statements, information and advice in this document do not
constitute any express or implied guarantee.
Note:
ODU Unit PoE Injector
Cap x 2
Strap x 2
Rubber Pad x2
Ethernet
Cable
It is important to comply with the precautions listed
below before installing.
It must be installed by qualified service personnel
who are well-trained in the correct procedures for
installing the equipment.
Avoid installing or working on equipment in adverse
weather conditions.
Do not disassemble the product. Warranty void if
seal is broken.
Please install the device underneath the eaves of
house, or the eaves of equipment room on rooftop.
Do not install the device on the lightning rod pole. A
random lightning could easily cause fatal damage to
the device.
Ensure that the device is within the shielding angle of
the lightning rod.
Lightning I Lightning induction I EMD damage is
NOT covered under warranty.
Before Installing the ODU
1.
2.
3.
4.
5.
6.
7.
8.
Step 1. Power off the ODU,
Insert SIM card into the SIM slot
located on the bottom panel.
Step 2. Place the
protective cap on the SIM
slot after insertion.
Step 3. Screw the protective
cap firmly to protect the SIM
slot against water and dust.
SIM Card Installation
Note: The ODU uses a Standard-size SIM card (Also called, Mini SIM
or 2FF SIM card)
Note: The Mounting Pole’s diameter should be 33-57mm.
Note: LAN Cable’s diameter should be 5-10mm.
Mounting kit :
Header Installation :
Installing Outdoor Unit
Wiring Diagram
Note: Make sure SIM is inserted correctly before powering up.
Step 1
Connect the (CAT 5e) Outdoor Ethernet cable
between ODU and the "Power + Data out" port
on the PoE.
Step 2
Connect the provided indoor Ethernet cable
between the 'Data In' port on the POE and your
PC or router.
Wall
PoE Injector
PC
Step 1
Step 2
For best signal level and connection quality, the ODU must
be aimed directly at the servicing tower. Fine tuning the
signal level can be done by making small, incremental
adjustment up, down or side to side in order to improve
signal, once established. The ODU signal strength level can
be observed on the RF Indicator LED lights located on the
bottom panel, as shown below. The more LEDS that are lit,
the stronger the signal level.
Adjusting For Optimal Installation
Weak Strong
RF LEDs
S
Y
S
S
I
M
E
T
H
R
U
N
(ODU) LED Behavior
When the ODU is powered on, the LEDs on the bottom panel
will have the following behavior.
State
Description LED Behavior LED illustration
LAN Connected The ETH LED On
S
Y
S
S
I
M
E
T
H
R
U
N
Signal Strength
weak
Signal strength is weak
Signal Strength
good
Signal strength is good
Signal Strength
strong
Signal strength is strong All signal LEDs steady on
LTE Scanning
RF
RF
RF
RF
LAN
Disconnected
The ETH LED Off
No SIM card The SIM LED Off
SYS linked The SYS LED On
SYS no link The SYS LED Off
CPE Operaon The RUN LED Blinking
SIM card normal The SIM Card is ready The SIM LED On
SIM card
abnormal
The SIM LED Blinking
RF
Firmware
Upgrading
RF
Signal Strength
medium
Signal Strength is medium
The CPE is searching for a
frequency channel or is
performing network entry
The CPE has a successful
connecon with a device
on the LAN
The CPE does not have an
Ethernet connecon with
the LAN
The SIM Card in abnormal
state
The SIM Card is Undetected
The CPE aached to LTE
network
The CPE not aached to
LTE network
The CPE is operang
properly
The CPE is upgrading the
firmware
All signal LEDs scrolling
blink one by one
The first three signal LEDs
steady on, the last one off
The first two signal LEDs
steady on, the last two off
All signal LEDs blinking
simultaneously
Only first signal LED steady
on, the other three off