Specialties note Matching instructions This model adopts RF remote control. The remote controller shall be matched with the air conditioner before operation, otherwise the remote control will be invalid. Before operation, please read the instructions in this page carefully and then do the corresponding matching operation. Note Please do the following operation within 2m from the unit. Matching is not needed anymore once it is done.
Explanation of Symbols Indicates a hazardous situation that, if not avoided, will result in death or serious injury. Indicates a hazardous situation that, if not avoided, could result in death or serious injury. Indicates a hazardous situation that, if not avoided, may result in minor or moderate injury. Indicates important but not hazard-related information, used to indicate risk of property damage. Indicates a hazard that would be assigned a signal word WARNING or CAUTION.
Precautions WARNING Operation and Maintenance This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance. Children shall not play with the appliance.
Precautions WARNING Maintenance must be performed by qualified professionals. Otherwise, it may cause personal injury or damage. Do not repair air conditioner by yourself. It may cause electric shock or damage. Please contact dealer when you need to repair air conditioner. Do not extend fingers or objects into air inlet or air outlet. It may cause personal injury or damage. Do not block air outlet or air inlet. It may cause malfunction.
Precautions WARNING Attachment Installation must be performed by qualified professionals. Otherwise, it may cause personal injury or damage. Must follow the electric safety regulations when installing the unit. According to the local safety regulations, use qualified power supply circuit and circuit break. Do install the circuit break. If not, it may cause malfunction. An all-pole disconnection switch having a contact separation of at least 3mm in all poles should be connected in fixed wiring.
Precautions WARNING Do not put through the power before finishing installation. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard. The temperature of refrigerant circuit will be high, please keep the interconnection cable away from the copper tube. The appliance shall be installed in accordance with national wiring regulations.
Precautions WARNING For the air conditioner with plug, the plug should be reachable after finishing installation. For the air conditioner without plug, an circuit break must be installed in the line. If you need to relocate the air conditioner to another place, only the qualified person can perform the work. Otherwise, it may cause personal injury or damage. Select a location which is out of reach for children and far away from animals or plants.If it is unavoidable, please add the fence for safety purpose.
Precautions FCC STATEMENT (1) this device may not cause harmful interference, and (2) this device must accept any interference received,including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Precautions IC STATEMENT This device complies with Industry Canada licenceexempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
Precautions IC STATEMENT antennes utilisées pour cet émetteur doivent être installées et doivent fonctionner à au moins 20 cm de distance des utilisateurs et ne doivent pas être placées près d’autres antennes ou émetteurs ou fonctionner avec ceux-ci. Les installateurs doivent s’assurer qu’une distance de 20 cm sépare l’appareil (à l’exception du combiné) des utilisateurs. Working temperature range Maximum cooling Maximum heating Indoor side DB/WB(ć ) 26.7/19.4 26.7/- Outdoor side DB/WB(ć ) 46.1/23.9 23.
Buttons on remote controller 1 2 3 4 5 7 6 8 10 9 +/- button 3 Cool button 4 Heat button 5 Fan button 6 I FEEL button 7 up down swing button 8 Mode button 9 Left right swing button 13 Air button 14 X-fan button 15 Light button 14 16 2 12 Humidity button/Health button 13 15 ON/OFF button 10 T-ON/T-OFF button 11 Clock button 11 12 1 16 Sleep button 17 WIFI button 17 Introduction for icons on display screen Operation mode Auto mode Cool mode WIFI INTELLIGENT Dry mode Fan
Introduction for buttons on remote controller Note: ● After putting through the power, the air conditioner will give out a sound. Operation indictor " " is ON (red indicator). After that, you can operate the air conditioner by using remote controller. ● Under on status, pressing the button on the remote controller, the signal icon " " on the display of remote controller will blink once and the air conditioner will give out a “de” sound, which means the signal has been sent to the air conditioner.
Introduction for buttons on remote controller 6 I FEEL button Press this button to start I FEEL function and " " will be displayed on the remote controller. After this function is set, the remote controller will send the detected ambient temperature to the controller and the unit will automatically adjust the indoor temperature according to the detected temperature. Press this button again to close I FEEL function and " " will disappear.
Introduction for buttons on remote controller ● When selecting auto mode, air conditioner will operate automatically according to ambient temperature. Set temperature can’t be adjusted and will not be displayed as well. Press "FAN" button can adjust fan speed. Press " " / " " button can adjust fan blowing angle. ● After selecting cool mode, air conditioner will operate under cool mode. Press "+" or "-" button to adjust set temperature. Press "FAN" button to adjust fan speed.
Introduction for buttons on remote controller 10 T-ON/T-OFF button ● T-ON button “T-ON” button can set the time for timer on. After pressing this button, " " icon disappears and the word “ON" on remote controller blinks. Press “+” or “-”button to adjust T-ON setting. After each pressing “+” or “-”button, T-ON setting will increase or decrease 1min. Hold “+” or “-”button, 2s later, the time will change quickly until reaching your required time. Press“T-ON”to confirm it. The word “ON” will stop blinking.
Introduction for buttons on remote controller 12 Humdity/health button Press this button to select your required operation mode. INTELLIGENT INTELLIGENT cancel Note:there is no this function for this unit. If press this button,the main unit will click, but it also runs under original status.
Introduction for buttons on remote controller In Sleep 1 and Sleep 2, the air conditioner will run according to a group of presetting temperature curves. ƽ Sleep 3 - the sleep curve setting under DIY Sleep mode: (1) Under Sleep 3 mode, long press "AIR" button, the remote controller will enter the setting of personalized sleep.
Function introduction for combination buttons About X-FAN function This function indicates that moisture on evaporator of indoor unit will be blowed after the unit is stopped to avoid mould. 1. Having set X-FAN function on: After turning off the unit by pressing ON/OFF button indoor fan will continue running for about 2 min. at low speed. In this period, press X-FAN button to stop indoor fan directly. 2.
Operation guide 1. After putting through the power, press "ON/OFF" button on remote controller to turn on the air conditioner. 2. Press "MODE" button to select your required mode: AUTO, COOL, DRY, FAN, HEAT. 3. Press "+" or " - " button to set your required temperature. (Temperature can’t be adjusted under auto mode). 4. Press "FAN" button to set your required fan speed: auto, low, medium and high speed. 5. Press "SWING" button to select fan blowing angle. Replacement of batteries in remote controller 1.
Operation of Smart Control (Smart Phone, Tablet PC) Special Function How to operate AC or auxiliary device with smart phone or tablet PC after matching: First of all: before using smart connection function, please make sure your smart phone or tablet computer uses the standard Android or iOS operating system. Please refer to the application program for the specific version. This air conditioner can connect 4 smart phones or tablet computers in maximum. 1.
Operation of Smart Control (Smart Phone, Tablet PC) 2. Turn on the AC WiFi: Turn the AC on. First, make sure the remote controller is matched. Then, long-press “WiFi” button on the remote controller for at least 3 seconds. If WiFi icon is shown, it means the WiFi function is turned on. 3. Enter the WiFi setting of your phone and search for the wireless network named G-xxxxxxxx. Take G-A0B40030 as an example. Connect the network. 4. Input the original password 12345 or 12345678 to connect the network. 5.
Operation of Smart Control (Smart Phone, Tablet PC) Attention: please change the name and key of the network during the first setting! 6. Left-slide the bottom function bar to “Settings” and click it to enter into internet setting interface. Click “Network Setting”, and input user name and password (the defaulted user name and password is admin) in the “Login” dialog box to enter into “Network Setting” to modify network name (e.g.
Operation of Smart Control (Smart Phone, Tablet PC) 9. Enter into the software interface again. Meanwhile, the short-distance remote control setting for your air conditioner is finished. How to reset the AC WiFi module: Turn unit off with the remote controller and disconnect the power of AC. Then re-connect the power. 1 minute later, press “WiFi” and “Mode” buttons simultaneously. If the AC gives out a beep sound, it means the WiFi module is successfully reset.
Operation of Smart Control (Smart Phone, Tablet PC) Function Introduction on Main Interface 1. Mode: It used for setting operation mode for air conditioner. You can select “Auto”, “Cooling”, “Drying”, “Fan” or “Heating” according to your requirement. Please refer to the part of remote controller for the detailed operation. 2. Temperature: It used for setting temperature. Set the indoor temperature according to your requirement. 3. Fan Speed: It used for setting fan speed.
Operation of Smart Control (Smart Phone, Tablet PC) Key Functions Instruction of Application Software 1. Preset: It’s with Timer On and Timer Off function. User can set Timer On and Timer Off according to actual individual requirement. 2.Functions: After entering setting interface, you can turn on or turn off Light, Purify, X-fan and Turbo functions and set Silent, Humidify, Air exchange and other modes. Please refer to the part of remote controller for the function instruction.
Operation of Smart Control (Smart Phone, Tablet PC) 4. Advanced: After entering advanced interface, you can set Sleep curve, Regional Swing, Noise and Power saving. !""#$%%&"'()*%+"#$%%&"'()*%",-'$(.%/"012"34.%5"6)7.,8,4-7$"34.%5"9:&%)8"34.%"7-. """"#,%/87"34.%;"<-.%)"012"34.%5"=4("'7-"/%8"8%3&%)78()%"7-."8,me. Under auto mode and fan mode, sleep curve function can’t be turned on. Only Traditional mode can be selected under dry mode.
Operation of Smart Control (Smart Phone, Tablet PC) !" @$+(&."A7&",$+(&?85(1$3+B&4"05,81+$,"0$'"+,4$$'"5,+1"8),"C&")4=5(1&4")88$'4+,-"1$"17&" """")815)9"+,4+*+45)9"'&>5+'&3&,1;"A7&"4&1)+9&4")4=5(13&,1"'),-&"+("4+00&'&,1"0$'"4+00&'&,1" """"3$4&9(6"%7+87"+("4&8+4&4"C2"+,4$$'"5,+1;" !" #$%&'"()*+,-.
Emergency operation If remote controller is lost or damaged, please use auxiliary button to turn on or turn off the air conditioner. The operation in details are as below: air conditioner. When the air conditioner is turned on, it will operate under auto mode. panel Display panel WARNING: aux. button Use insulated object to press the auto button Clean and maintenance WARNING ■ Turn off the air conditioner and disconnect the power before cleaning the air conditioner to avoid electric shock.
Clean and maintenance NOTICE: Checking before use-season 1. Check whether air inlets and air outlets are blocked. 2. Check whether circuit break, plug and socket are in good condition. 4. Check whether drainage pipe is damaged. NOTICE: Checking after use-season 1. Disconnect power supply. Notice for recovery 1. Many packing materials are recyclable materials. Please dispose them in appropriate recycling unit. 2.
Malfunction analysis General phenomenon analysis Please check below items before asking for maintenance. If the malfunction still can’t be eliminated, please contact local dealer or qualified professionals. Phenomenon Check items Solution ● Whether it's interfered severely ● Pull out the plug. Reinsert (such as static electricity,stable the plug after about 3min, and voltage)? then turn on the unit again. Indoor unit can’t receive remote controller’s signal or remote controller has no action.
Malfunction analysis Phenomenon Air conditioner can’t operate Mist is emitted from indoor unit’s air outlet Set temperature can’t be adjusted Cooling (heating) effect is not good. Check items Solution ● Power failure? ● Wait until power recovery. ● Is plug loose? ● Reinsert the plug. ● Air switch trips off or fuse is burnt out? ● Ask professional to replace air switch or fuse. ● Wiring has malfunction? ● Ask professional to replace it.
Malfunction analysis Phenomenon Odours are emitted Check items Solution ● Whether there’s odour source, ● Eliminate the odour source. such as furniture and cigarette, ● Clean the filter. etc. Air conditioner ● Whether there’s interference, such as thunder, wireless operates normally suddenly devices, etc. Outdoor unit has vapor “Water flowing” noise Cracking noise ● Disconnect power, put back power, and then turn on the unit again.
Malfunction analysis Error Code ● When air conditioner status is abnormal, temperature indictor on indoor unit will ation of error code. Error code E5 E6 E8 U8 H6 Troubleshooting It can be eliminated after restarting the unit. If not , please It can be eliminated after restarting the unit. If not , please It can be eliminated after restarting the unit. If not,please It can be eliminated after restarting the unit. If not,please It can be eliminated after restarting the unit.
