Instruction Manual
Parts List Important Please check the list below to make sure you have all of the following parts before you proceed. If you are missing parts please contact the GReddy Authorized Dealer you purchased the unit from. Turbo Timer Power Harness Main Harness 1pc. 1pc. 1pc. Double-sided Tape Instruction Manual 1 set Instruction Manual Tie Strap 3 pcs. 1pc.
Installation (using Optional Turbo Timer Harness) (1) (2) (3) Follow the key switch to it’s electrical connector, then unplug the harness and place the Optional Turbo Timer harness in-line with the key switch harness. Connect the supplied power harness in between the 3-pin connector of the optional harness and the 4-pin connector of the Turbo Timer. Then connect the black wire with the loop connecter to a good chassis ground.
Installation (without Optional Turbo Timer Harness) (1) (2) (3) (4) Follow the key switch to it’s electrical connector, then unplug the harness. Find the appropriate wires with either a factory service manual or a volt meter. (see 2.3 for wiring) Cut off the 3-pin connector on power harness. Then splice and solder the appropriate wires to the power harness. (be sure to cover connections) Then connect the black wire with the loop connecter to a good chassis ground.
Wiring Diagram The wires coming out form the key switch usually consist of: 12 v - 12 volt constant power ON - Ignition power ACC - Accessory power ST - Starter signal Other than these four wires, the vehicle may have two ON wires. 12V ACC ON ST 12V ACC ON ON ST Wiring Procedure: (1) Cut the Power harness close to the 3-pin connector (2) Use a volt meter or test light to find the appropriate wires. Connect the Red wire to the 12v, the Green to to ON, and the Blue to ACC using solder.
Harness Connections Parking Brake Feature: (1) Remove the cover over the parking brake and find the parking switch wire(s). (see you factory service manual) (2) * If there is one wire, make sure the wire: shows 0 volts, when the parking brake is engaged. and shows 12 volts, when the parking brake is released. * If there are two wires, find the wire that: shows 0 volts, when the parking brake is engaged. and shows 12 volts, when the parking brake is released.
Turbo Timer Functions Back OPTION Switch Used to connect the Remote Switching System (sold separately) Line Switch Display TIME Button (Referred as "T") Used when switching the main modes. Used to change the countdown time and set-up time. SELECT Button (Referred as "S") Used when switching the sub modes. Used to start the stopwatch mode. POWER Button (Referred as "P") Turns the Turbo Timer "ON" or "OFF" Used when switching the main and sub modes. Shuts off engine and timer during count down.
Display Description 1 2 3 6 7 8 9 4 5 10 11 1 Attack Mode indicator. Flashes when Attack timer is activated. 2 Stopwatch Mode indicator. Flashes when the stopwatch is activated. 3 Speed Mode indicator. 4 Displayed while in Battery Mode. 5 Best lap time indicator. Flashes the best lap time during Stopwatch Mode. 6 Count Down Mode indicator. 7 Battery Mode indicator. 8 Auto Mode indicator in the Count Down Mode. 9 Displayed while in Attack mode or Speed Mode.
Display Description P+S+T P+S+T P+S+T Stopwatch Mode Count Down Mode Battery Mode Auto Lo Mode Voltage Display Mode Lap Mode Auto Hi Mode Battery Warning Lo Mode Lap Read Mode Preset 1 Mode Battery Warning Hi Mode Split Mode P+S P+S P+S Split Read Mode Preset 2 Mode 8
Display Description P+S+T P+S+T Attack Mode 0-200m Mode 0-400m Mode 200-400m Mode 0-100km/h Mode 0-200km/h Mode 50-100km/h Mode P+S+T Speed Mode Setup Mode Speedometer Mode Sound Mode Speed peek Mode Line Switch Mode Speed Warning Set up Mode RPM Setup Mode Speedometer Set up Mode 9
Operation Check Parking Brake Safety Feature Operation Check (1) Engage parking brake. Manual Transmission: Place into Neutral Automatic Transmission: Place into Park. Start the engine. Make sure the Turbo Timer powers up with the music and display lights operating. (note: The Turbo Timer may be turned "Off" if so, press the "POWER" button once to turn on the unit) (2) Press P + S to select to "P-1" or "P-2" Mode. P+S P+S This shows P-1 selected. After 2 sec. default value will display.
Operation Check Vehicle Speed Signal Safety Feature Operation Check Warning ! Before moving your vehicle, be sure that the area around your vehicle is clear. If not, you may cause an accident. (1) Go over check procedure 4.3 "Parking Brake Feature Check" before continuing. Turn off the key switch (2) Carefully, place the vehicle into gear and move the vehicle slowly. Turbo Timer and engine should then turn off. During count down, Place the car in gear and move the vehicle.
Countdown Mode Auto Countdown Mode Auto Timer Mode automatically calculates a suggested count down time for your vehicle, according to your car’s RPM. You may also choose 2 count down time offset ratios "Hi" or "Lo". This will add a preset time to your calculated count down time. On some vehicles, there is a possibility that the Auto Mode will not function properly due to difference in usable rpm range.
Countdown Mode Preset Mode There are two Preset Countdown mode you can select from. Preset mode can be set from 0 sec. to 9 min 59 sec. by increments of 10 sec. The factory setting is: 1 min. for P-1 3 min. for P-2 Preset Countdown Mode Setting (1) Press the P+S button to display P-1 or P-2. Two sec. later, the current minimum offset value will be displayed. This show P-1 being selected. 2 sec. later (2) By pressing the T button (once), you can increase the preset value by 10 sec.
Battery Mode Battery Voltage Display Mode This feature displays the "real-time" battery voltage. There is a voltage warning feature that can be turned on and off. The warning buzzer and the back light will flash when the voltage exceeds the set voltage. (1) To go to the Battery Mode from Countdown Mode, press P+S+T buttons and release S button first. (2) V will display with the " real-time" voltage. 14 "Real-time" battery voltage will display.
Battery Mode Voltage Warning Display Mode When the Warning is set, the warning buzzer and the back light will flash when the voltage exceeds the set voltage. This feature will only work while in battery mode. (1) Press the P+S button to display -L- or -H-. Two sec. later, the current minimum offset value will be displayed. At this time the back light will turn red. P-1 is selected here. 2 sec.
Stopwatch Mode Lap Mode This feature can record up to 30 lap times from 0 ~ 9’ 59" 99. Also while recording the time, the best lap will be indicated by "BEST" on the display. (1) Press the P+S+T button to go to Stopwatch Mode. Two sec. later, 0’00" will display. *if there are recorded time stored in the memory, the 0’00" will flash. To clear the memory, hold down T button over 5 sec. 2 sec later, Standby mode will display. press S button to start.
Stopwatch Mode Lap Read Mode This feature allows the user to look over the recorded lap times. Up to 30 lap time can be recalled one by one. The best lap time will be indicated with "BEST" shown in the display. (1)While in Stopwatch Mode, press the P+S button to go to Lap Read mode. L-1 will display indicating lap 1. If the displayed time is the best lap time, "BEST" will flash on the display. (2)Press the T button once to go to the next lap time stored Press T button to go to next lap time.
Stopwatch Mode Split Mode This feature can record up to 10 split times from 0 ~ 9’ 59" 99. Lap time can also be recorded at the same time. (1) While in the Stopwatch mode, press the P+S button to go to Split Mode. Two sec. later, 0’00" will display. 2 sec later, Standby mode will display. press S button to start. *if there are recorded time stored in the memory, the 0’00" will flash. To clear the memory, hold down T button over 5 sec.
Stopwatch Mode Split Read Mode This feature allows the user to look over the recorded split times. Up to 10 split time can be recalled one by one in order. Lap time can also be recalled at the same time. (1)While in Stopwatch Mode, press the P+S button to go to Split Read mode. P-1 will display indicating Split point 1 followed by the recorded time. (2)Press the T button once to go to the next split time stored. At any time hold down the S button to recall the lap time.
Attack Mode 0-200m, 0-400m, 200-400m, 0-100km/h, 0-200km/h, 50-1000km/h Mode This feature allows the user to record 0-200m, 0-400m, 200-400m, 0-100km/h, 0-200km/h, 50-1000km/h times. Important! - This feature should only be used on a race track where it is safe. Please never try on the public highways. *This feature requires the wiring of the vehicle speed sensor signal wire. *To record 0-200km/h time, the vehicle must be equipped with speed limiter cut device. (1) Press P+S+T to go to main Attack Mode.
Attack Mode This shows 0-200m Mode is selected goes to stand-by mode. Countdown start by pressing T button "Beep" Auto Start by Moving the vehicle. "Beep" The timing will start with a "Beep" as soon as the vehicle starts to move. When the vehicle reaches the distance or the speed the mode is set to the timing will stop automatically, and display the time.
Speed Mode Speedometer Mode This feature allow the user to monitor the "real time" vehicle speed. With use of the Speed Warning feature, buzzer and flashing back light will warn the driver when the speed exceeds the set warning speed. (1) Press the P+S+T button to go to main Speed Mode. The current speed will display. * Speedometer display range is 0 ~ 399km/h. Speed Peek Mode This feature will display the highest speed recorded while in Speed Mode.
Speed Mode Speed Warning Mode This feature allow the user to set the warning speed to warn the driver when the speed exceeds the set warning speed with a buzzer and flashing back light. *This feature only work while in the Speed Mode (1)While in Speed Mode, press the P+S button to go to Speed Warning Setup mode. SET will display followed by the current warning setting. * the warning range is: 0 ~ 399 km/h. Press S button to set up. (2)Press the S button to change the set position.
Speed Mode Speedometer Setup Mode This feature allow the user to set the Turbo Timer speedometer to match the vehicle’s speedometer. (1)While in Speed Mode, press the P+S button to go to Speedometer Setup mode. (2)Get the vehicle speed up to 40km/h. Press the T button to set the speed. After two cycles (3) When the setup is complete, 40km/h will display. Press T to set * To clear the memory, hold down T button over 5 sec. and repeat the procedure above.
Setup Mode Sound Mode This feature allow the user to turn the sound ON or OFF. (1) While in Setup Mode, press the P+S button to go to Setup mode. Sud will display indicating Sound Mode. (2) Hold down the T button for 5 sec to turn OFF. * Hold down the T button for 5 sec again to turn the sound back on. 25 2 sec later. Hold down the T button for 5 sec.
Setup Mode Line Switch Mode This feature is used when the count down does not properly operate. If the engine shuts down when the IG key is turned off with out counting, follow these instructions. (1) While in Setup Mode, press the P+S button to go to Line Switch mode. (2) Hold down the T button for 2 sec to change to Acc. Default setting is IG. * Hold down the T button for 2 sec again to change back to IG (3) Change the switch on the back of the head unit to Acc. Hold down T button for 2 sec.
Setup Mode RPM Set Mode This feature is used when the Auto Mode does not operate properly or to set the Turbo Timer RPM to match the vehicle’s tachometer. (1) While in Setup Mode, press the P+S button to go to RPM Set mode. (2)The current RPM will display, If the RPM does not match the vehicle’s tachometer, bring the engine speed to constant RPM (2000 or 3000) and press S button once. The number on the very left will start to flash. Current RPM will display.
