Specification

Form No. 179-07438X-0611MCK
178-00376X-0611MCK
IN THE U.S.
FOR TECHNICAL INFORMATION: 1-866-583-BLUE (2583)
FOR SALES INFORMATION: 1-800-232-2436
THE DOW CHEMICAL COMPANY
DowBuildingSolutions•200Larkin•Midland,MI48674
IN CANADA
FOR TECHNICAL INFORMATION: 1-866-583-BLUE (2583) (English)•1-800-363-6210(French)
FOR SALES INFORMATION: 1-800-232-2436 (English)•1-800-565-1255(French)
DOW CHEMICAL CANADA ULC
DowBuildingSolutions•Suite2100•450–1stSt.SW•Calgary,ABT2P5H1
www.dowgreatstuff.com
Installation
GREAT STUFF PRO™ Wall & Floor
Adhesive is easy to apply using a
PRO Series foam dispensing gun. To
ensure best adhesion performance,
GREAT STUFF PRO™ Wall &
Floor Adhesive should be applied
to substrates that are structurally
sound and free of standing water,
snow, ice, dirt, mud, oil or other
loose materials and release agents
that may impair adhesion. Painted
surfaces and protective coatings
should be removed, sanded or
thoroughly roughened. Concrete and
masonry substrates should be cured
before bonding. Materials should be
cut and fit-checked before applying
adhesive.
Shake container vigorously for
one minute before dispensing and
between uses. To attach a PRO
Series foam dispensing gun, invert
can and screw gun onto adapter,
then adjust flow control knob to
adjust bead size (1/2" [13 mm]
recommended).
Adhesive can be applied in a
continuous zigzag bead or in parallel
beads, ensuring that the adhesive
layer will completely cover joists
and framing where wood panels and
drywall edges abut.
Construction material can then be
positioned over the substrate, and
NOTICE: No freedom from any patent owned by Dow or others is to be inferred. Because use conditions and applicable laws may differ from one location to another and may change with time, Customer is responsible for
determining whether products and the information in this document are appropriate for Customer's use and for ensuring that Customer's workplace and disposal practices are in compliance with applicable laws and other
government enactments. The product shown in this literature may not be available for sale and/or available in all geographies where Dow is represented. The claims made may not have been approved for use in all countries
or regions. Dow assumes no obligation or liability for the information in this document. References to "Dow" or the "Company" mean the Dow legal entity selling the products to Customer unless otherwise expressly noted. NO
EXPRESS WARRANTIES ARE GIVEN EXCEPT FOR ANY APPLICABLE WRITTEN WARRANTIES SPECIFICALLY PROVIDED BY DOW. ALL IMPLIED WARRANTIES INCLUDING THOSE OF MERCHANTABILITY AND FITNESS FOR
A PARTICULAR PURPOSE ARE EXPRESSLY EXCLUDED.
CAUTION: When cured, these products are combustible and will burn if exposed to open flame or sparks from high-energy sources. Do not expose to temperatures above 240ºF (116ºC). For more information, consult MSDS, call
Dow at 1-866-583-BLUE (2583) or contact your local building inspector. In an emergency, call 1-989-636-4400 in the U.S. or 1-519-339-3711 in Canada.
GREAT STUFF PRO™ Insulating Foam Sealants contain isocyanate and a flammable blowing agent. Read the label and Material Safety Data Sheet carefully before use. Eliminate all sources of ignition before use. Wear long
sleeves, gloves, and safety glasses or goggles. Provide adequate ventilation or wear proper respiratory protection. Contents under pressure.
Building and/or construction practices unrelated to building materials could greatly affect moisture and the potential for mold formation. No material supplier including Dow can give assurance that mold will not develop in any
specific system.
®™Trademark of The Dow Chemical Company (“Dow”) or an affiliated company of Dow
Habitat for Humanity is a registered service mark owned by Habitat for Humanity International
Printed in U.S.A.
a proud partner of
McKAYXXXXXX
firm pressure applied. Substrates
should be butted together within
10 minutes of dispensing adhesive.
If bead has skinned over, it must
be scraped off and reapplied.
Supplemental mechanical fasteners
should be installed after applying
adhesive for best bond. Initial bond
typically occurs within two hours,
with full cure in seven days
depending on conditions. Cure
times will be shorter at higher
temperature and humidity, and
longer at lower temperature and
humidity.
Excess adhesive can be cleaned
from the substrate while still uncured
using a dry cloth, putty knife or paint
scraper. Cured adhesive must be
mechanically removed.
GREAT STUFF PRO™ Wall & Floor
Adhesive should not be used in
continuous underwater applications
or on substrates with surface or
standing water present.
For more information, consult the
installation instructions (Form No.
179-07439/178-00378) or contact
your Dow sales representative.
Storage and
Shelf Life
GREAT STUFF PRO™ Wall &
Floor Adhesive should be stored
between 65°F and 85°F (18°C and
29°C) for fast and easy application
performance. GREAT STUFF PRO™
Wall & Floor Adhesive has a shelf
life of 12 months when stored in
the original closed container. Open
containers should be stored upright
attached to dispensing gun when
not in use. See package labeling for
more information.
Standards
GREAT STUFF PRO™ Wall &
Floor Adhesive complies with the
following standards:
• ASTMD3498–Standard
Specification for Adhesives for
Field-Gluing Plywood to Lumber
Framing for Floor Systems
•HUDUM60a–Performance
specification for all flooring
adhesive products used in HUD
manufactured housing
•ASTMD6464–Standardfor
Expandable Foam Adhesives for
Fastening Gypsum Wallboard to
Wood Framing
•CaliforniaSpecicationsCA25-4
– Standard for the Evaluation
of Adhesives for Structural
Use in Multi-unit Manufactured
Housing and Commercial Coach
Construction
Contact your Dow sales
representative or local authorities
for state/provincial and local
building code requirements
and related acceptances.