User manual

In the basic transmitter display, use a fi nger or the
provided stylus to touch the gear icon labelled "B":
000 000
000
000
mz
000%
000%
000
000
BATT TIME 00: 01: 23
Graubele
M 1
0:01:23
NORMAL
000:00.0
000:00.0
4.1V
RX TX
RX 00.0V
Touch
The display switches to the green base menu. Use a
fi nger or the provided stylus to touch the "Trim Step"
menu item:
BACK
SYSTEM
BASE
FUNCTION
Model Sel
E.P.A
Model Type
Rev/Slow
Sub-Trim
Motor
Timer
TX ctl
Fail Safe
Trim Step
Servo
Out.Swap
CH Set
Touch
The two control control sticks come with digital trimming.
With each click, briefl y touching the trimming lever,
moves the initial position of the control stick by a
certain value. If it is held, the trimming moves in the
corresponding direction with increasing speed.
The current trim positions are displayed in the main
display, and adjustments are audible. It is therefore easy
to fi nd the middle position during fl ight without looking at
the display: When you pass over the middle position, a
brief pause is inserted.
The current trim values are automatically saved when
the model memory is switched.
In addition, the digital trim of a newly delivered mz-18
HoTT transmitter and mz-24 HoTT transmitter always
has a global effect within a model memory (with the
Trim settings
Trim settings
exception of trim the throttle/brake control stick, also
generally termed control function "THR" (channel 1)).
T:CO (common) or T:SE (single) is specifi ed at the
top right of the submenu "Channel set", page 92, of
the base menu. CH1 trim is generally set to "common",
i.e., independent of the Quick Link, in the software
program:
BACK
Graubele
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
ST 1
ST 2
ST 3
ST 4
NONE
NONE
NONE
NONE
NONE
NONE
NONE
NONE
SERVO
Throttle
Aileron 1
Elevator
Rudder
Aileron 2
Aux 1
Aux 2
Aux 3
Aux 4
Aux 5
Aux 6
Aux 7
T:CO
Note:
In contrast to the display of the 12-chan-
nel mz-24 HoTT transmitter shown in this
section, only channels 1 … 9 are shown in the
display of the 9-channel mz-18 HoTT transmitter.
"STEP" line (trim step)
With each click, the four digital trim levers shift the
neutral position of the respective control stick by an
increment adjustable between "01" and a max. of "10"
in each direction. The maximum trim path is always
approximately ±30 % of the control path independent of
the selected number of trim steps. This setting is always
global independent of the setting T:CO (common)
or T:SE (single).
To change the current step of a trim control, use a fi nger
or the provided stylus to touch the corresponding value
fi eld in the "STEP" line, for example:
BACK
NORMAL
Graubele
S
T1
STEP
POS.
SET
Digital Trim 1
T4
INC
RES
DEC
04
00%
000%
04
–07%
NONE
NONE
04
04
T2 T3
+13%
–06%
000%
000%
000%
Digital Trim 2
SET
VIEW
Touch
The color of the fi eld switches from red to blue:
BACK
NORMAL
Graubele
S
T1
STEP
POS.
SET
Digital Trim 1
T4
INC
RES
DEC
04
00%
000%
04
–07%
NONE
NONE
04
04
T2 T3
+13%
–06%
000%
000%
000%
Digital Trim 2
SET
VIEW
Set the desired value with the INC or DEC button at
the right edge, for example:
BACK
NORMAL
Graubele
S
T1
STEP
POS.
SET
Digital Trim 1
T4
INC
RES
DEC
04
00%
000%
04
–07%
NONE
NONE
04
02
T2 T3
+13%
–06%
000%
000%
000%
Digital Trim 2
SET
VIEW
Touch the RES button to reset a changed value in the
blue (and hence active) fi eld to the default.
Use the same procedure with the other trim controls.
86
Basic menu - Trim setting
S1006_mz-24.3.en.indd 86 17.12.2014 15:21:46