User manual

BACK
Graubele
TX OUT SET
RF ON/OFF
RANGE TEST
BIND ON/OFF
SET
OFF
OFF
OFF
RX1
RX2
DSC OUTPUT
SET
OFF
PPM10
NORMAL
RF TYPE
99sek
Touch
BACK
Graubele
TX OUT SET
RF ON/OFF
RANGE TEST
BIND ON/OFF
SET
OFF
OFF
CHK
RX1
RX2
DSC OUTPUT
SET
OFF
PPM10
NORMAL
RF TYPE
99sek
Binding is complete once (within a period of approx-
imately 10 seconds) the flashing red receiver LED
shines green continuously. Your model memory/re-
ceiver combination is now operable. At the same
time, instead of OFF , an abbreviation of the receiv-
er type such as 12CH appears for the receiver GR-
24 HoTT receiver which comes standard:
BACK
Graubele
TX OUT SET
RF ON/OFF
RANGE TEST
BIND ON/OFF
SET
OFF
ON
12CH
RX1
RX2
DSC OUTPUT
SET
OFF
PPM10
NORMAL
RF TYPE
99sek
At the same time, RF transmission is switched on
(see the line "RF ON/OFF" in the following display).
If the red receiver LED continues to flash for more
than 10 seconds, the binding process was unsuc-
cessful. At the same time, OFF appears again in
the line "BIND ON/OFF". Change the positions of
the associated antennas and try the entire proce-
dure again.
• GR-12L receivers
The red LED on the receiver shines.
Hold down the SET button on the receiver until, after
about 3 seconds, the red LED goes dark for around
3 seconds. Then release the SET button on the
receiver. As long as the LED is dark, the receiver is
in binding mode.
As described above, within this 3 second window,
start binding the receiver to the current model
memory by touching one of the two buttons in the
"BIND ON/OFF" line with a finger or the provided
stylus, for example.
Binding has been successful if the receiver LED
remains dark and the receiver display switches
to 6CH .
If the red receiver LED shines red again, the binding
process was unsuccessful. At the same time, OFF
appears again in the line "BIND ON/OFF". Change
the positions of the associated antennas and try the
entire procedure again.
Out.Swap (receiver output)
As mentioned in the introduction to the section "Binding
receivers", the mz-18 HoTT and mz-24 HoTT trans-
mitters allow you use this menu item to distribute the
transmitter control channels within a receiver as desired,
and you can also distribute the 9 or 12 receiver control
channels to the two receivers as preferred. This distribu-
tion will be termed mapping or channel mapping in the
following.
Switch on your receiver and, with a finger or the
provided stylus, touch the receiver (such as "RX1") to
be mapped in the line "Out.Swap":
BACK
Graubele
TX OUT SET
RF ON/OFF
RANGE TEST
BIND ON/OFF
SET
OFF
ON
12CH
RX1
RX2
DSC OUTPUT
SET
OFF
PPM10
NORMAL
RF TYPE
99sek
Touch
Channel assignment within a receiver
Like the channel mapping described on page 118 (also
termed "channel mapping" in the "Telemetry" menu),
you can easily distribute transmitter control channels at
the receiver inputs to the outputs, or servo connections,
of the selected receiver:
BACK
NORMAL
Graubele
CH
CH
CH
CH
1
CH
CH
2
3
4
5
6
OUT1
OUT2
OUT3
OUT4
OUT5
OUT6
CH
CH
CH
CH
7
CH
CH
8
9
10
11
12
OUT7
OUT8
OUT9
OUT10
OUT11
OUT12
DEC
RES
INC
SERVO
STO
Note:
In contrast to the display of the 12-channel
mz-24 HoTT transmitter in this section, only
channels 1 … 9 are offered in the display of
the 9-channel mz-18 HoTT transmitter.
After the desired output has been selected by touching
the channel button with a finger over the provided stylus
in the line of the desired receiver output, the color
switches from red to blue, for example:
75
Basic menu - Transmitter setting
S1006_mz-24.3.en.indd 75 17.12.2014 15:21:42