User manual

In the basic transmitter display, use a fi nger or the
provided stylus to touch the gear icon labelled "B":
000 000
000
000
mz
000%
000%
000
000
BATT TIME 00: 01: 23
Graubele
M 1
0:01:23
NORMAL
000:00.0
000:00.0
4.1V
RX TX
RX 00.0V
Touch
The display switches to the green base menu. Touch the
menu item "TX ctl" with a fi nger or the provided stylus.
BACK
SYSTEM
BASE
FUNCTION
Model Sel
E.P.A
Model Type
Rev/Slow
Sub-Trim
Motor
Timer
TX ctl
Fail Safe
Trim Step
Servo
Out.Swap
CH Set
Touch
Transmitter settings
This menu allows you to confi gure transmitter-specifi c
functions such as "Binding", "Transmitter outputs", "RF
ON/OFF", "RF type", "Range test" and "DSC output":
BACK
Graubele
TX OUT SET
RF ON/OFF
RANGE TEST
BIND ON/OFF
SET
OFF
OFF
OFF
RX1
RX2
DSC OUTPUT
SET
OFF
PPM10
NORMAL
RF TYPE
99sek
Transmitter control
Transmitter settings
Bind ON/OFF
To establish a telemetry connection to the transmitter,
Graupner HoTT receivers must be "trained" to commu-
nicated exclusively with one specifi c model (memory) of
a Graupner HoTT transmitter. This procedure is termed
"binding" and only needs to be done once for each
new receiver/model memory combination (and can be
repeated anytime).
Important instructions:
•
When binding, make sure that the trans-
mitter antenna is always far enough
away from the receiver antenna. Main-
tain a distance of 1 meter to be on the safe side.
Otherwise, you risk endangering the connection
with the feedback channel and causing malfunc-
tions.
• Make sure that the receiver power supply is
correct. If the power supply is too low, the
receiver LEDs will react as described below
in response to your binding attempt, but the
binding will not work.
• When binding to other receivers, note that other
switched-on receivers already bound to the
transmitter (and hence not directly affected by
the binding process) enter fail safe mode while
the transmitter is binding.
Binding several receivers per model
If desired, several receivers per model can be bound. In
the related programs of the mz-18 HoTT and mz-24
HoTT receivers, you can directly manage two receivers
bound to each active model memory and use a menu
to distribute the 9 or 12 transmitter control channels
between the two receivers (see below in this section):
First bind the two receivers one by one as described
below.
During subsequent operation, only the
receiver establishes a telemetry link to the
transmitter that was either last bound to
the active model memory, or was selected in the
"RECEIVER SELECT" line in the "Telemetry" menu,
for example:
BACK
Graubele
RX SELECT
SETTING & DATA VIEW
SENSOR
RF STATUS VIEW
VOICE TRIGGER
RX1
>>
>>
>>
>>
Any telemetry sensors which are installed in the model
should therefore be connected to this receiver since
only the data received through the feedback channel
of the receiver selected in this line is evaluated by the
transmitter. The second receiver (and all other receivers)
run independently at the same time in model memory-
independent slave mode.
Binding the transmitter and receiver
Switch off the power supply to your receiver at this time
(at the latest).
• GR-16 and GR-24 receivers
The red LED fl ashes on the receiver.
Hold down the SET button on the receiver until, after
about 3 seconds, the fl ashing red LED fl ashes red/
green for around 3 seconds. Then release the SET
button on the receiver. As long as the LED is fl ashing
red/green, the receiver is in binding mode.
Within this 3 second window, start binding the
receiver to the current model memory by touching
one of the two buttons in the "BIND ON/OFF" line
with a fi nger or the provided stylus, for example.
74
Basic menu - Transmitter setting
S1006_mz-24.3.en.indd 74 17.12.2014 15:21:42