User manual

Note:
This menu is hidden when selecting a model
confi guration "NO POWER" in the basic
settings of the "Model Sel" or "Model
type" menu.
In the basic transmitter display, use a fi nger or the
provided stylus to touch the gear icon labelled "B":
000 000
000
000
mz
000%
000%
000
000
BATT TIME 00: 01: 23
Graubele
M 1
0:01:23
NORMAL
000:00.0
000:00.0
4.1V
RX TX
RX 00.0V
Touch
The display switches to the green base menu. Touch
the menu item "Motor" (airplane or glider with electric
motor) or "Throttle Cut" (helicopter with electric or gas
engine and airplane with gas engine) with a fi nger or the
provided stylus.
BACK
SYSTEM
BASE
FUNCTION
Model Sel
E.P.A
Model Type
Rev/Slow
Sub-Trim
Motor
Timer
TX ctl
Fail Safe
Trim Step
Servo
Out.Swap
CH Set
Touch
NOTE:
"Motor" is working over the complete range
(-100 to +100 % CH1 control stick position)
and "Throttle Cut" is only working, when CH1
control stick position is below -66 %.
Motor (electric motor)
Throttle Cut (gas engine)
Switchable throttle cut or motor limiter
BACK
SYSTEM
BASE
FUNCTION
Model Sel
E.P.A
Model Type
Rev/Slow
Sub-Trim
THR.CUT
Timer
TX ctl
Fail Safe
Trim Step
Servo
Out.Swap
CH Set
Touch
Motor / Throttle Cut
In the "Motor" or "Throttle Cut" menu, you can switch
off a speed controller by a switch, or move a servo for
the throttle control into motor OFF position (or to idle
position). This option can also be used as an emergency
Cut OFF function as well. The motor OFF position, or for
example an idle position, is designated in the value fi eld
of the "SET" line and needs to be determined through
experimentation.
The speed controller or the throttle servo only assumes
the set position after a switch has been activated and
the switching threshold in the "SET" line is undershot by
the CH1 control stick.
• If the set percentage in the "SET" line is greater
than the current Ch1 control stick position, that is,
the current position represented by the green arrow
to the left of the bar graph is below the switching
threshold, switching occurs when the switch is in the
ON position.
• If the set percentage in the "SET" line is less than
the current CH1 control stick position, that is, the
current servo position represented by the green
arrow to the left of the bar graph is above the
switching threshold, the speed controller reduces
the motor speed, or the throttle servo closes the
carburettor as specifi ed in the "SET" line once the
CH1 control stick position falls below the switching
threshold when the switch is in the ON position.
In this motor OFF position, the speed controller or
throttle servo are disabled until the selected switch
is switched. The throttle servo or speed controller is
then moved beyond the preprogrammed switching
threshold with the Throttle/brake control stick.
A threshold of -100% the servo position is the default in
the value fi eld of the "SET" line:
BACK
Graubele
ACT
CTL
SET
DEC


NORMAL
RES
INC
S
–100%
ON
INH
Programming
To change the default for the switching threshold or
"Motor OFF" position, touch the value fi eld in the "SET"
line with a fi nger or the provided stylus:
BACK
Graubele
ACT
CTL
SET
DEC


NORMAL
RES
INC
S
–100%
ON
INH
Touch
The color of the fi eld switches from red to blue:
BACK
Graubele
ACT
CTL
SET
DEC


NORMAL
RES
INC
S
–100%
ON
INH
72
Basic menu - Motor / THR.CUT
S1006_mz-24.3.en.indd 72 17.12.2014 15:21:41