User manual

In the basic transmitter display, use a fi nger or the
provided stylus to touch the gear icon labelled "B":
000 000
000
000
mz
000%
000%
000
000
BATT TIME 00: 01: 23
Graubele
M 1
0:01:23
NORMAL
000:00.0
000:00.0
4.1V
RX TX
RX 00.0V
Touch
The display switches to the green base menu. Touch
the menu item "Sub-Trim" with a fi nger or the provided
stylus.
BACK
SYSTEM
BASE
FUNCTION
Model Sel
E.P.A
Model Type
Rev/Slow
Sub-Trim
Motor
Timer
TX ctl
Fail Safe
Trim Step
Servo
Out.Swap
CH Set
Touch
Sub-Trim
The servo middle position is for adapting servos that are
not standard (servo middle position with a pulse length
of 1.5 ms or 1500 µs ) as well as for minor adaptations,
for example fi ne adjustment to the neutral position of the
control surfaces on the model.
Independent of trim levers and any mix settings, the
neutral position can be shifted around ±125% within the
maximum servo travel of ±150%. The servo is always
adjusted directly independent of all other trim and mix
settings.
Sub-Trim
Setting the neutral position of servos
Note that if the neutral position is adjusted
strongly, servo travel on one side may be
restricted since the total travel is limited to
±150% for electronic and mechanical reasons.
BACK
Graubele
SERVO
CH 1.
CH 2.
CH 3.
CH 4.
CH 5.
CH 6.
CH 7.
CH 8.
CH 9.
CH 10.
CH 11.
CH 12.
INC
RES
DEC
000%
000%
000%
000%
000%
000%
000%
000%
000%
000%
000%
000%
Note:
•
Move the trim lever into the middle position
before changing the middle values.
• In contrast to the display of the 12-channel mz-
24 HoTT transmitter in this section, only channels
1 … 9 are offered in the display of the 9-channel mz-
18 HoTT transmitter.
To change the neutral position of a specifi c servo, touch
the corresponding button, for example:
BACK
Graubele
SERVO
CH 1.
CH 2.
CH 3.
CH 4.
CH 5.
CH 6.
CH 7.
CH 8.
CH 9.
CH 10.
CH 11.
CH 12.
INC
RES
DEC
000%
000%
000%
000%
000%
000%
000%
000%
000%
000%
000%
000%
Touch
The button color changes from red to blue:
BACK
Graubele
SERVO
CH 1.
CH 2.
CH 3.
CH 4.
CH 5.
CH 6.
CH 7.
CH 8.
CH 9.
CH 10.
CH 11.
CH 12.
INC
RES
DEC
000%
000%
000%
000%
000%
000%
000%
000%
000%
000%
000%
000%
Change the value by touching INC or DEC on the
right to the outside, for example:
BACK
Graubele
SERVO
CH 1.
CH 2.
CH 3.
CH 4.
CH 5.
CH 6.
CH 7.
CH 8.
CH 9.
CH 10.
CH 11.
CH 12.
INC
RES
DEC
000%
000%
+012%
000%
000%
000%
000%
000%
000%
000%
000%
000%
Touch the RES button to reset a changed value in the
blue fi eld back to the default.
Touch the SERVO button in the top right of the display
to open the graphic display of the servo travel and
positions described in greater detail on page 90 and
activate (if desired) the "Servo test" function integrated
in this display:
To go to the "Home menu", leave the "Sub-Trim" display
by touching the BACK button at the top left:
BACK
Graubele
SERVO
CH 1.
CH 2.
CH 3.
CH 4.
CH 5.
CH 6.
CH 7.
CH 8.
CH 9.
CH 10.
CH 11.
CH 12.
INC
RES
DEC
000%
000%
+012%
000%
000%
000%
000%
000%
000%
000%
000%
000%
Touch
70
Basic menu - Sub-Trim
S1006_mz-24.3.en.indd 70 17.12.2014 15:21:40