User manual

• Setting a transmitter-side symmetrical delay
depending on the Quick Link
Important:
In contrast to the left column, numbers
CH1 … CH9 for the mz-18 HoTT
transmitter and CH1 … CH12 for the
mz-24 HoTT transmitter refer to the control-side
control channels..
NOTE
Set a symmetrical delay for the transmitter-
side control signal with buttons with the
standard labelling 0.0s . A delay which is
set here affects the servo that has the number of the
delayed receiver connector as well as all servos
controlled by the control element assigned to control
function X.
To set a control-side delay, touch the button normally
labelled 0.0s with a finger or the provided stylus, for
example CH8.
BACK
NORMAL
Graubele
S
1.
2.
3.
4.
5.
.6
NOR
REV
NOR
NOR
REV
NOR
7.
8.
9.
10.
11.
12.
INC
RES
DEC
0.0s
0.0s
0.0s
0.0s
0.0s
0.0s
NOR
NOR
NOR
NOR
NOR
0.0s
0.0s
0.0s
0.0s
0.0s
0.0s
NOR
Touch
The button color changes from red to blue:
BACK
NORMAL
Graubele
S
1.
2.
3.
4.
5.
.6
NOR
REV
NOR
NOR
REV
NOR
7.
8.
9.
10.
11.
12.
INC
RES
DEC
0.0s
0.0s
0.0s
0.0s
0.0s
0.0s
NOR
NOR
NOR
NOR
NOR
0.0s
0.0s
0.0s
0.0s
0.0s
0.0s
NOR
Touch the INC button at the right edge of the
display to gradually increase the value to a maximum
of 9.9 seconds:
BACK
NORMAL
Graubele
S
1.
2.
3.
4.
5.
.6
NOR
REV
NOR
NOR
REV
NOR
7.
8.
9.
10.
11.
12.
INC
RES
DEC
0.0s
0.0s
0.0s
0.0s
0.0s
0.0s
NOR
NOR
NOR
NOR
NOR
0.0s
4.5s
0.0s
0.0s
0.0s
0.0s
NOR
Touch the DEC button underneath to reduce the
value to a minimum of 0.0 s, and touch the RES
button to reset the changed value back to the default.
Touch the S button in the top right of the display to
open the graphic display of the servo travel and po-
sitions described in greater detail on page 90 and
activate (if desired) the "Servo test" function integrated
in this display.
Use the same procedure for the other settings.
To go to the "Home menu", leave the "REVERSE/
SLOW" display by touching the BACK button at the
top left:
BACK
NORMAL
Graubele
S
1.
2.
3.
4.
5.
.6
NOR
REV
NOR
NOR
REV
NOR
7.
8.
9.
10.
11.
12.
INC
RES
DEC
0.0s
0.0s
0.0s
0.0s
0.0s
0.0s
NOR
NOR
NOR
NOR
NOR
0.0s
4.5s
0.0s
0.0s
0.0s
0.0s
NOR
Touch
69
Basic menu - Servo reverse/servo delay
S1006_mz-24.3.en.indd 69 17.12.2014 15:21:39