User manual

In the basic transmitter display, use a fi nger or the
provided stylus to touch the gear icon labelled "B":
000 000
000
000
mz
000%
000%
000
000
BATT TIME 00: 01: 23
Graubele
M 1
0:01:23
NORMAL
000:00.0
000:00.0
4.1V
RX TX
RX 00.0V
Touch
The display switches to the green base menu. Touch the
menu item "E.P.A" with a fi nger or the provided stylus.
BACK
SYSTEM
BASE
FUNCTION
Model Sel
E.P.A
Model Type
Rev/Slow
Sub-Trim
Motor
Timer
TX ctl
Fail Safe
Trim Step
Servo
Out.Swap
CH Set
Touch
E.P.A
In this display, the parameters are set that exclusively
relate to the servo, that is the servo path and angle of
rotation as well as its limit.
The set values always refer to the settings in the
submenu "(Servo)Sub-Trim" on page 70.
BACK
Graubele
CH 1.
CH 2.
CH 3.
CH 4.
CH 5.
150%
150%
150%
150%
150%
INC
RES
DEC
100%
100%
100%
100%
100%
100%
100%
100%
100%
150%
150%
150%
150%
150%
100%
– Limit Limit +
– Travel +
NEXT
SERVO
E.P.A
End Point Adjustmen
Note:
In order to reach control channels with
numbers higher than CH5, touch NEXT [next
page] at the right column of the display.
To change a current value, touch the desired button with
a fi nger or the provided stylus, for example:
BACK
Graubele
CH 1.
CH 2.
CH 3.
CH 4.
CH 5.
150%
150%
150%
150%
150%
INC
RES
DEC
100%
100%
100%
100%
100%
100%
100%
100%
100%
150%
150%
150%
150%
150%
100%
– Limit Limit +
– Travel +
NEXT
SERVO
Touch
The button color changes from red to blue:
BACK
Graubele
CH 1.
CH 2.
CH 3.
CH 4.
CH 5.
150%
150%
150%
150%
150%
INC
RES
DEC
100%
100%
100%
100%
100%
100%
100%
100%
100%
150%
150%
150%
150%
150%
100%
– Limit Limit +
– Travel +
NEXT
SERVO
Repeatedly touch the INC button at the right edge of
the display to gradually increase the current value, and
touch the DEC button to lower the value in the active
value fi eld. Touch the RES button to reset a changed
value back to the default.
Use the same procedure for all the other settings.
Touch the SERVO button in the top right of the display
to open the graphic display of the servo travel described
in greater detail on page 90 and activate (if desired)
the "Servo test" function integrated in this display by
touching the VIEW fi eld:
BACK
Graubele
CH 1.
CH 2.
CH 3.
CH 4.
CH 5.
150%
150%
150%
150%
150%
+
RES
–
104%
111%
107%
077%
088%
097%
088%
115%
111%
150%
150%
150%
150%
150%
076%
– Limit Limit +
– Travel +
SW
SERVO
Touch
BACK
Graubele
VIEW
NORMAL
1 2 3
4
5 6
7
8 9
10
11
12
000%
000%
000%
000%
000%
000%
000%
000%
000%
000%
000%
000%
BACK
Graubele
VIEW
NORMAL
1 2 3
4
5 6
7
8 9
10
11
12
000%
000%
000%
000%
000%
000%
000%
000%
000%
000%
000%
000%
+0.5s
INC
RES
DEC
OFF
Note:
In contrast to the display of the 12-channel
mz-24 HoTT transmitter in this section, only
channels 1 … 9 are offered in the display of
the 9-channel mz-18 HoTT transmitter.
Once you activate one or more control elements of
your transmitter, the resulting servo travel is graphically
displayed, for example:
66
Basic menu - Servo path/servo limit
S1006_mz-24.3.en.indd 66 17.12.2014 15:21:38