User manual

WIZ.
NORMAL
CH
CH6
CH7
CH8
CH5-12 CTL
000%
000%
INC
RES
DEC
000%
CH5
000%
000%
000%
000%
000%
CH10
CH11
CH12
CH9
OFFSET OFFSET
Touch
• "Pitch curve"
In this display you can adjust the pitch curve and,
as of firmware version 1.021, you can additionally
change in the line "PITCH MIN" the operating direc-
tion of the pitch stick to your needs:
Firmware version V 1.021 and higher
"Pitch min." line
In the helicopter program for the mz-18 HoTT and
mz-24 HoTT transmitters, the "rear" throttle position
is the "Pitch min." position by default.
With this option, which was introduced in firmware
version V1.021, the control direction of the pitch con-
trol stick can be easily switched from "Pitch min.
rear" to "Pitch min. front" or vice versa by touching
the REAR or FORWARD button in the "Pitch min."
line:
WIZ.
NORMAL
IN
OUT
POINT
OFF
INC
ENT
DEC
Y-axis
TRIM
X-axis
ST OFF
Curve
–100%
–100%
–100%
L
Pit.CRV
Pitch min.
REAR
Touch
After the button is touched, the confirmation prompt
appears:
on page 38.
2. Display "Control path setting" CH5 … 9 or
CH5 … 12
The above-described classic dual rate/expo
function now has a non-switchable dual rate
function or control path setting for the control
functions 5 … 9 of the mz-18 HoTT transmitter
and 5 … 12 of the mz-24 HoTT transmitter.
As shown in the above illustration, repeatedly
touch the button with a finger or the provided
stylus in the "CH" line until "CH5-9“ or "CH5-12"
appears:
WIZ.
NORMAL
CH
CH6
CH7
CH8
CH5-12
+100%
+100%
INC
RES
DEC
+100%
CH5
+100%
+100%
+100%
+100%
+100%
+100%
+100%
+100%
+100%
+100%
+100%
+100%
+100%
CH10
CH11
CH12
CH9
D/R –
D/R –
D/R + D/R +
Note:
In contrast to the display of the
12-channel mz-24 HoTT transmitter,
only channels 1 … 9 are offered in the
display of the 9-channel mz-18 HoTT transmitter.
Analogous to the previously described displays,
touch the corresponding button with a finger or
the provided stylus to change a current value,
and increase or decrease the value by touching
the INC or DEC buttons at the right side of the
display the appropriate number of times.
The adjustment range is ±125%.
Touch the RES button to reset a changed value
in a blue (active) value field to the default value.
3. Display "Offset setting" CH5 … 9 and 5 … 12
The last display in this series makes it possible to
adjust a control offset within the range of ± 125%
for each of inputs 5 … 9 (mz-18 HoTT) and 5 …
12 (mz-24 HoTT).
As shown in the illustration at the top left,
repeatedly touch the button with a finger or the
provided stylus in the "CH" line until "CTL CH5-9“
or "CTL CH5-12" appears:
WIZ.
NORMAL
CH
CH6
CH7
CH8
CH5-12 CTL
000%
000%
INC
RES
DEC
000%
CH5
000%
000%
000%
000%
000%
CH10
CH11
CH12
CH9
OFFSET OFFSET
In contrast to the display of the
12-channel mz-24 HoTT transmitter,
only channels 1 … 9 are offered in the
display of the 9-channel mz-18 HoTT transmitter.
Analogous to the previously described displays,
touch the corresponding button with a finger
or the provided stylus to change a current
value, and raise or lower the value by touching
the INC or DEC buttons at the right side of the
display the appropriate number of times.
The adjustment range is ±125%.
Touch the RES button to reset a changed value
in a blue (active) value field to the default value.
Touch the WIZ. button at the top left of the display to
leave this menu and go to the next:
52
Basic menu - Model selection
S1006_mz-24.3.en.indd 52 17.12.2014 15:21:31