User manual

BACK
NEXT
01
MODEL NAME 1
02
03
04
05
06
SEL
NEW
IMP.M
EXP.M
RES
CPY
MODEL NAME 1
MODEL NAME 2
MODEL NAME 3
MODEL NAME 4
MODEL NAME 5
MODEL NAME 6
MODEL
CHANGE
YES
NO
Touch
… "Please wait" appears for about 1 second:
BACK
NEXT
01
MODEL NAME 1
02
03
04
05
06
SEL
NEW
IMP.M
EXP.M
RES
CPY
MODEL NAME 1
MODEL NAME 2
MODEL NAME 3
MODEL NAME 4
MODEL NAME 5
MODEL NAME 6
MODELL
WECHSEL
J
N
Please
Wait!!
After this message disappears, the model has changed,
and the name of the selected model memory appears in
the top line for confirmation:
BACK
NEXT
01
MODEL NAME 2
02
03
04
05
06
SEL
NEW
IMP.M
EXP.M
RES
CPY
MODEL NAME 1
MODEL NAME 2
MODEL NAME 3
MODEL NAME 4
MODEL NAME 5
MODEL NAME 6
Fail Safe
setup
t.b.d.
As of firmware version V 1.023 as illustrated
above the message "Fail Safe setup t.b.d." appears for
a few seconds, if you have not yet made any fail-safe
settings in the selected model memory.
NEW (create new model)
Note:
Switch between model memories
with SEL .
In order to reach model memories with numbers
higher than 06, touch NEXT (next page) at the top
right of the display.
As described above, to set up a new model, select
a free model memory or a model memory that has
already been assigned but is no longer required. Instead
of NEXT , touch NEW with a finger or the provided
stylus at the right edge of the display:
BACK
NEXT
01
MODEL NAME 1
02
03
04
05
06
SEL
NEW
IMP.M
EXP.M
RES
CPY
MODEL NAME 1
MODEL NAME 2
MODEL NAME 3
MODEL NAME 4
MODEL NAME 5
MODEL NAME 6
Touch
After you touch NEW , the selection window in the
following display appears. In this window, you can
choose between manual and assistant-controlled
programming, or press NO to terminate the process.
In the following menus, the options for configuring a
fixed-wing model or helicopter are offered depending on
the selected model type. Since the manual programming
of a fixed-wing model is described in this section, touch
the MAN button with a finger or the provided stylus:
BACK
NEXT
01
MODEL NAME 1
02
03
04
05
06
SEL
NEW
IMP.M
EXP.M
RES
CPY
MODEL NAME 1
MODEL NAME 2
MODEL NAME 3
MODEL NAME 4
MODEL NAME 5
MODEL NAME 6
Select
MAN.
WIZ.
NO
Touch
Note:
Assistant-controlled model programming will
be subsequently addressed with reference
to programming a helicopter.
Manually programming the basic settings of a new
model
Manually programming of a model is always started by
entering the model name.
"Model name"
MAN.
CAPS
Current Model Name
MODEL NAME 2
New Model Name
A B C D E F
G H I J K L
M
N
O P
Q
R
S
T
U
V W
X
Y
Z
CL SP
DE
EN
SPECIAL
NUM
On the screen keypad, touch the first character of
the model name to be entered with a finger or the
provided stylus.
Switch between capital and small letters and vice
versa with the CAPS button at the bottom edge of
the screen, and similarly, press the NUM button to
go to the numbers 0 … 9 and special characters.
To enter a space, touch the SP [Space] button.
You can select other special characters by touching
the SPECIAL button.
45
Basic menu - Model selection
S1006_mz-24.3.en.indd 45 17.12.2014 15:21:27