User manual

Control, switch and control switch assignment
Basic procedure
In many places in the program, you can actuate a
control function with a freely selectable control (ST1 …
4, DV1 … max. D4, DT1 and DT2, SL1 and SL2), switch
(S1 … 8), or switch between settings by a switch (S1 …
8) or control switch (see below). In both cases, multiple
assignments are possible. (The distinction between a
control and switch is explained in the section "Definition
of terms" on page 37.) It should be noted however
that incorrect responses may arise from functional
overlaps such as using the same physical switch as a
switch to switch between Q.Link and as a control for
Q.Link trim. In such cases, you should change your
switch assignment.
Since the same method is used to assign the controls
and switches in all relevant menus, the basic procedure
will be explained at this point which will allow you to
focus on the specifics in the detailed menu descriptions.
Control and switch assignment
In the "CH set" submenu (control assignment), starting
on page 92, you can …
BACK
Graubele
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
ST 1
ST 2
ST 3
ST 4
NONE
NONE
NONE
NONE
NONE
NONE
NONE
NONE
SERVO
Throttle
Aileron 1
Elevator
Rudder
Aileron 2
Aux 1
Aux 2
Aux 3
Aux 4
Aux 5
Aux 6
Aux 7
T:CO
… assign transmitter inputs 5 … 9 and 5 … 12 to
operate servos, as well as any control stick (ST1 …
ST4) and control identified as "DVx", "SLx" or "DTx", or
any switch identified as "S1 … S8".
The following window appears in the display after
touching the corresponding button, such as the NONE
button to the right of "AUX 1" at the bottom edge of the
display, with a finger or the provide stylus:
BACK
Graubele
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
ST 1
ST 2
ST 3
ST 4
NONE
NONE
NONE
NONE
NONE
NONE
NONE
NONE
SERVO
Throttle
Aileron 1
Elevator
Rudder
Aileron 2
Aux 1
Aux 2
Aux 3
Aux 4
Aux 5
Aux 6
Aux 7
T:CO
Select
CLR
NO
Actuate the desired control (control stick 1 … 4, DV1 …
max. DV4, SL1 … SL2, or DT1 … DT2) or switch (S1 …
S8), such as the right proportional rotary control SL1:
BACK
Graubele
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
ST 1
ST 2
ST 3
ST 4
NONE
SL 1
NONE
NONE
NONE
NONE
NONE
NONE
SERVO
Throttle
Aileron 1
Elevator
Rudder
Aileron 2
Aux 1
Aux 2
Aux 3
Aux 4
Aux 5
Aux 6
Aux 7
T:CO
Note:
The controls are only recognized after a
specific path. Therefore move the control to
the left or right, forward or backward until the
assignment appears on the display. If the length of travel
is insufficient, move the control in the opposite direction.
Switch and control switch assignment
The places in the program where a switch or control
switch can be assigned are identified with "CTL", such
as the following illustration of the Dual Rate/Expo
display:
BACK
CH
D/R
EXP
CTL
AILE
+100%
+100%
NULL
INC
RES
DEC
NORMAL
000%
000%
Graubele
S
SYM
OFF
On the right next to "CTL", touch the red NONE button
with a finger or the provided stylus. The following
appears in the display:
BACK
CH
D/R
EXP
CTL
ELEV
+100%
+100%
NULL
INC
RES
DEC
NORMAL
000%
000%
Graubele
S
SYM
OFF
Select
CLR
NO
Switch assignment
Operate the desired switch:
BACK
Graubele
OFF
SW 1
OFF
OFF
38
Control, switch, and control switch assignment
S1006_mz-24.3.en.indd 38 17.12.2014 15:21:24