User manual

In the right top half of the display, the current cell
voltages are displayed of a lithium polymer battery
with up to six cells, as well as the level of a fuel tank
measured by a sensor connected to the module.
The abbreviations have the following meanings:
Value Explanation
1-BAT-2 BATT 1 to the left, and BATT 2 to the right
QUA Signal quality expressed as percentage
FUEL Fuel level/tank display
ml accumulated consumption in ml
1-TEMP-2 Temperature of sensors 1 and 2
BAT-1 Cell voltage of cells 1 … 6
ALT Current altitude (only with module 33611)
m/s Ascent/descent in m/1 s (only with module
33611)
m/3s Ascent/descent in m/3 s (only with module
33611)
VOLT Current voltage of the battery connected
to the module
AMP Momentary current in amps
ELECTRIC AIR MODULE
BACK
NEXT
m/s -000.1m/s
CURRENT
QUA 100
000.0A
40.0
80.00
0000m
ALT
VO LT
00000mAh
00.0V
60.020.0
CAPACITY
m/3s 000m/3s
RPM 000000
BACK
NEXT
00.0V 00.0V
1-BAT-2
BAT 1
80.0
70
0
0
3.0V
-20
0.0
-20
-020°C -020°C
1-TEMP-2
2525
40.0 40.0
0.0
0.0
0.0
0.0
0.0
C6
C5
C4
C3
C2
C1
C7
BAT 2
3.0V
0.0
0.0
0.0
0.0
0.0
0.0
C6
C5
C4
C3
C2
C1
C7
0.0
0.0
4.2V
4.2V
These two displays that alternate about every 4 seconds
visualize the data of an electric air module (order No.
33620).
Further information on this module can be found in the
Annex or on the Internet at www.graupner.de for the
respective product.
Depending on the configuration of the module with ad-
ditional sensors, the following data can be permanently
shown on the display.
Firmware versions up to and including V 1.020
The two displays appear alternately about every 4
seconds.
Firmware versions V 1.021 and above
In order to switch between the two displays, touch one
of the dials or scales in the display with a finger or the
provided stylus.
1st Display
At the top edge of the display, "QUA" identifies the
quality, expressed as a percentage, of the signal coming
from the transmitter. The line above shows the current
ascent/descent in m/1 s and m/3 s. The graphic at the
right edge of the display visualizes the current height
relative to the location.
The central graphic is a graphic and numeric display of
the current voltage of the connected battery. The scale
to the left shows the momentary current in amps, and
the scale to the right shows the momentary charge
of the power source connected to the module at the
battery connector.
Note:
To correctly display the data, the charge must
be entered beforehand in the "Telemetry"
menu.
2nd Display
The two graphics to the left show the current voltage
measured by the temperature and voltage sensors
(order No. 33612 and 33613) connected to the model
from up to two batteries (BAT-1 and BAT-2). They also
show the corresponding temperature: On the left side
you can see the data of sensor 1 and on the right side
the data of sensor 2.
The right half of the display shows the current cell
voltages of the (max.) seven-cell battery pack connected
to balancer connector 1 (L) and possibly 2 (H).
The abbreviations have the following meanings:
Value Explanation
V Current voltage
A Momentary current
ALT Current altitude
m/s Ascent/descent in m/1 s
m/3s Ascent/descent in m/3 s
215
Telemetry data display
S1006_mz-24.3.en.indd 215 17.12.2014 15:22:56