User manual

Warnings
Depending on the context, different warning windows
appear in the display for the mz-18 HoTT transmitter
and the mz-24 HoTT transmitter. These can be divided
into two groups:
Warning display
These smaller windows primarily appear after the
transmitter is switched on and indicate certain operat-
ing states. In the following illustration, for instance, the
red dot after "CH1-POS" indicates that the CH1 control
stick, or as of fi rmware version V 1.023, the gas servo,
connected to output 1 on a surface model and to output
6 on a helicopter model, is not in the idle position and
there is the risk of a runaway engine.
Note:
The default "Rear idle" can be switched to
"Front idle" for fi xed-wing models in the "THR.
CRV" menu, page 144, by inverting the
control curve.
The bottom line also indicates that a receiver has not
been bound to the current model memory.
000 000
000
000
mz
000%
000%
000
000
BATT TIME 00: 01: 23
MODEL NAME 1
M 1
0:01:23
NORMAL
000:00.0
000:00.0
3.8V
RX TX
RX 00.0V
Warning
Thr.HOLD
Thr.POS
Thr.CUT
QLink
BIND is not setup
SET
F/S setup t.b.d
Touch SET with a fi nger or the provided stylus to go
directly to the "Transmitter control" display in which
you can link the receiver to the model memory as
described on page 74:
BACK
MODEL NAME 1
TX OUT SET
RF ON/OFF
RANGE TEST
BIND ON/OFF
SET
OFF
OFF
OFF
RX1
RX2
DSC OUTPUT
SET
OFF
PPM10
NORMAL
RF TYPE
99sek
Or touch the BACK button at top left to terminate the
procedure.
Firmware versions up to and including V 1.022
If in contrast a receiver is already linked to the current
model memory and it is not switched on or out of the
range when the transmitter is switched on, a related
warning window appears:
000 000
000
000
mz
000%
000%
000
000
AKKUZEIT 00: 01: 23
MODELLNAME 1
M 1
0:01:23
NORMAL
000:00.0
000:00.0
3.8V
RX TX
RX 00.0V
WARNUNG
Warning
Thr.HOLD
Thr.POS
Thr.CUT
QLink
Please select RF ON/OFF
ON
Normal signal
OFF
Firmware versions as of V 1.023 and higher
As of fi rmware version V 1.023 and higher, switching on
the transmitter generally also activates the HF transmis-
sions and the display shown above appears in the cen-
tre of the transmitter display. At the same time, audible
warning signals sound for a few seconds.
You now have the option of waiting a few seconds until
the display disappears automatically or maintaining the
HF transmissions by manually tapping the ON button
with your fi nger or the provided stylus, or switching them
off by tapping the OFF button.
In the fi eld between the two green lines, the message
"Normal signal" indicates that the transmitter is set to
normal remote control. Alternately, messages such as
"TEACH signal" or "PUPIL signal" can appear here.
Another – possible – variant is to display "F/S setup t.b.d"
as an indication that no fail-safe settings have yet been
made.
Answer the request "Turn RF ON/OFF" in the area be-
low as desired by touching the button ON or OFF with
a fi nger or the provided stylus.
Note:
By default, only the monitoring of the "THR
position" is activated in the display of the
submenu "Warning" of the system menu,
page 201.
"acute warning" display
You can open this display by touching mz in the middle
of the transmitter's basic display:
000 000
000
000
mz
000%
000%
000
000
BATT TIME 00: 01: 23
MODEL NAME 1
M 1
0:01:23
NORMAL
000:00.0
000:00.0
4.2V
RX TX
RX 00.0V
Touch
BACK
CLR
ON
TX VOLT
00
3.6V
AUTO LOAD
RX VOLT
00
3.7V
STRENGTH
00
000%
ESC CUR.
00
000.0A
ESC VOLT
00
00.0V
STRENGTH ALARM
ON
And touch the BACK button at top left to close the
display.
22
Description of the transmitter - Warning
S1006_mz-24.3.en.indd 22 17.12.2014 15:21:17