User manual

Swash mixer
Flight-phase-dependent setting of pitch, roll and elevation
In the basic transmitter display, use a fi nger or the
provided stylus to touch the gear icon labelled "F":
000 000
000
000
mz
000%
000%
000
000
BATT TIME 00: 01: 23
Starlet
M 2
0:01:23
NORMAL
000:00.0
000:00.0
4.2V
RX TX
RX 00.0V
Touch
The display switches to the blue function menu. Touch
the menu item "S.MIX" with your fi nger or the provided
stylus:
BACK
SYSTEM
BASE
FUNCTION
Q.Link
PIT.CRV
D/R,EXP
THR.CRV
Gyr/Gover
THR.HOLD
S.Limit
Swash
S.MIX
THR.MIX
Prog.MIX
PIT>>RUDD
Trainer
Telemetry
Touch
In the following menu "S.MIX" addressed below, the
fl ight-phase dependent mixers "AILE >> ELEV", "ELEV
>> AILE", "PITC >> AILE", and "PITC >> ELEV"
are described. These menus are used especially for
compensating asymmetrical helicopter reactions to
control commands and to adjust helicopters with multi-
blade rotors.
• Flight-phase-dependent settings
If you have created fl ight phases in the submenu
"Q.Link" and have assigned an appropriate name, it
appears at the top right such as "NORMAL". Activate
the corresponding switches if desired to switch be-
tween Quick Links:
BACK
NORMAL
Starlet
S
ACT
ELEV >> AILE
PITC >> AILE
PITC >> ELEV
AILE >> ELEV
INH
INH
INH
INH
>>
>>
>>
>>
ON
ON
ON
ON
SET CTL
MIX.TYPE
• ACT column (active)
In in the value fi elds of this column, indicate wheth-
er the function of the line is generally blocked ( INH )
or ON .
Once you set this value fi eld to ON , you can indivi-
dually switch on and off the effect of the respective
control element on the selected mixer for specifi c
quick links with a control assigned in the option fi eld
"CTL" (see below in the section).
• SET column (setting)
Touch one of the four buttons in this column with a
fi nger or the provided stylus to open the setting page
for the selected mixer, for example:
BACK
NORMAL
Starlet
S
ACT
ELEV >> AILE
PITC >> AILE
PITC >> ELEV
AILE >> ELEV
INH
INH
INH
INH
>>
>>
>>
>>
ON
ON
ON
ON
SET CTL
MIX.TYPE
Touch
BACK
NORMAL
Starlet
S
EXP
(RATE)
AILE >> ELEV
000%
INC
RES
DEC
A
000%
000%
000%
B
Based on the defaults shown here, you can adapt
the current settings as needed by touching the value
fi eld to be changed with a fi nger or the provided sty-
lus to activate it, for example:
BACK
NORMAL
Starlet
S
EXP
(RATE)
AILE >> ELEV
000%
INC
RES
DEC
A
000%
000%
000%
B
Touch
The color of the value fi eld switches from red to blue:
BACK
NORMAL
Starlet
S
EXP
(RATE)
AILE >> ELEV
000%
INC
RES
DEC
A
000%
000%
000%
B
Then change the current value in the blue (active)
value fi eld by touching the INC or DEC buttons at
the right edge of the display, for example:
194
Helicopter model function menu - Helicopter mixer
S1006_mz-24.3.en.indd 194 17.12.2014 15:22:45